Land Rover Range Rover recalls

For affected vehicles the repair procedure for a prior safety recall was incorrect. As a result the front suspension knuckles have been replaced with those of an incorrect specification.

Fix: Vehicles will have both front suspension knuckles replaced.

4 vehicles · built 24 Nov 2015 to 18 Jul 2017

A concern has been identified on certain AJ20-D6 engines where the Front End Auxiliary Drive (FEAD) belt idler pulley may over-rotate following a high torsion input and lead to a clash with and damage to the oil pressure and temperature sensor. A damaged oil pressure and temperature sensor can lead to an oil leak from the engine which can result in a slip hazard for following road users particularly two-wheeled vehicles.

Fix: Vehicles will have the Front-End Auxiliary Drive (FEAD) idler pulley replaced.

1,044 vehicles · built 3 Jan 2024 to 6 Dec 2024

A concern has been identified where the connector to the driver’s airbag at the clockspring may experience fretting corrosion over time. This can lead to an increased resistance in the driver’s airbag circuit potentially resulting in the airbag failing to deploy when requested to do so. An airbag which fails to deploy as-intended will increase the risk of injury in the event of a crash.

Fix: Vehicles will have a protective lubricant gel applied to the driver’s airbag connector terminals.

30,444 vehicles · built 25 Sep 2020 to 4 Jun 2026

A concern has been identified on certain 2026 model year Range Rover Range Rover Sport and Range Rover Velar vehicles where the audio amplifiers may have been subject to water damage and may not provide any audio output including no seat belt reminder audible warnings to the driver. A seat belt reminder audible warning chime that does not alert of an unlatched seat belt can increase the risk of occupant injury in the event of a crash.

Fix: Affected vehicles will have the audio amplifier replaced.

3 vehicles · built 17 Feb 2026 to 27 Feb 2026

The manufacturer has identified a concern on certain Range Rover and Range Rover Sport vehicles where the adhesion process used to re-attach the panoramic roof side finishers during vehicle quality rework operations in the assembly plant may not have been sufficient. An inadequately adhered panoramic roof side finisher could over time come partially or completely loose. This could result in distraction to the driver or other road users or in the event of complete detachment harm to other road users particularly pedestrians or two-wheeled vehicles and increase the risk of injury or a crash.

Fix: Vehicles will have the panoramic roof side finisher removed and securely attached.

35 vehicles · built 12 Aug 2021 to 12 Oct 2025

The manufacturer has identified a concern on certain Range Rover and Range Rover Sport plug-in hybrid vehicles where due to inadequate penetration of welding between the cells the battery’s capacity and therefore the vehicle’s electric range may be depleted below the design intent condition. A below-specification electric range will not meet the as-certified value for the vehicle and is therefore non-compliant to emissions legislation.

Fix: Vehicles will have the hybrid battery/modules replaced.

541 vehicles · built 26 Jan 2023 to 5 Jan 2025

A concern has been identified on certain Range Rover & Range Rover Sport PHEV (Plug-in Hybrid Electric Vehicle) vehicles containing high-voltage batteries with cells manufactured between 11th and 12th April 2018. Cathode damage introduced during the cell folding process can lead to high time-in-service cell degradation.

Fix: Data will be extracted from vehicles then the high voltage traction battery pack will be replaced.

19 vehicles · built 24 Jul 2018 to 11 Sep 2018

On Affected vehicles it is possible that moisture has entered the Gear Shift Module (GSM) during the assembly process. Under certain conditions there is a risk that this moisture could result in non-illumination of the Light Emitting Diode (LED) indicating the selected gear. Non-illumination of the LED gear indicator adjacent to the shifter would not conform to regulated requirements for automatic transmission control position indicator illumination.

Fix: Affected vehicles will have the Gear Shift Module replaced.

113 vehicles · built 19 Aug 2025 to 29 Aug 2025

The manufacturer identified that on a small number of vehicles the JLR N759 safety recall repair procedure had not been carried out correctly. The suspension knuckles had not been replaced in all cases where the repair instruction directed a replacement leaving the defect present on the vehicles.

Fix: Both front suspension knuckles will be inspected for the presence of any cracks. Where no crack is present and where available a retaining bracket will be fitted to the joint. Where cracks are found or a bracket is not available the front suspension knuckle will be replaced.

42 vehicles · built 8 Oct 2014 to 26 Mar 2015

Jaguar Land Rover in conjunction with law enforcement and insurance bodies is aware of the increase in thefts of vehicles in specific geographical locations within the United Kingdom. there is no fault with Jaguar Land Rover's security systems and they continue to meet stringent automotive legislation. Jaguar Land Rover is offering owners guidance on how to maximise vehicle security and protect against theft.

Fix: Vehicle registered keepers will be sent a security guidance letter only - there is no repair action.

14,179 vehicles · built 17 Jan 2013 to 19 Jun 2015

On affected vehicles the second-row centre seat belt buckle may have been manufactured incorrectly. An internal obstruction to the seat belt tongue can prevent correct latching. In the event of a crash an insecurely latched seat belt buckle could increase the risk of personal injury.

Fix: Vehicles will have the centre seat belt buckle and buckle retaining bolt replaced.

178 vehicles · built 19 Dec 2024 to 19 Feb 2025

For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.

Fix: The software enhancement will deploy this update and reduce the theft risk.

16,299 vehicles · built 2 Feb 2015 to 6 Nov 2017

On affected vehicles the 48V cable could become too close to an underbody cross-brace and rub against the metal cross-brace exposing the cable core resulting in a short circuit and risk of fire.

Fix: Inspect harness and as needed reposition the routing bracket as necessary.

1 vehicle · built 28 Jun 2024 to 1 Jul 2024

For affected vehicles the clutch plates within the hybrid transmission may have been manufactured with a flatness out of tolerance to the engineering specification.

Fix: Diagnostic test to determine whether the clutch packs within the transmission are operating as expected. Any transmissions which fail the test will be replaced.

22 vehicles · built 6 Sep 2023 to 1 Dec 2023

On affected vehicles the incorrect specification of plastic was used to manufacture the oil filter housing. This housing may over time and with vehicle use crack. This could result in oil under pressure leaking and coming into contact with hot components of the engine which may result in a fire. Additionally oil may leak onto the road surface posing a skid hazard.

Fix: Replace the oil filter housing complete with filter and associated O-rings.

291 vehicles · built 14 Apr 2021 to 5 Mar 2024

For the affected vehicle a concern has been identified where the there is an inadequate depth of weld (penetration) between the busbar and the anode in the module of the Plug-in Hybrid Electric Vehicle (PHEV) battery.

Fix: Replacement of the traction battery.

1 vehicle · built 11 Jan 2024 to 18 Jan 2024

A concern has been identified where the clamps used to secure the fuel injectors into the cylinder head on certain AJ20-D6 engines may crack allowing the injector to come loose. This loose injector could become unseated allowing fuel to be pushed past the injector seal from the combustion chamber or the fuel feed system.

Fix: A fuel leak in this area could result in fuel spill onto hot engine components which may result in a fire.

1 vehicle · built 24 Nov 2023 to 24 Nov 2023

For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.

Fix: The software enhancement will deploy this update and reduce the theft risk.

524 vehicles · built 2 Nov 2020 to 4 May 2022

For affected vehicles the manufacturer has developed a software enhancement to further increase vehicle security.

Fix: The software enhancement will deploy this update and reduce the theft risk.

14,517 vehicles · built 25 Sep 2020 to 26 Feb 2024

On affected vehicles there is concern that the structural adhesive applied to the bodyshell has been mis-applied.

Fix: Install two rivets and seal with approved sealant.

4 vehicles · built 3 Oct 2023 to 13 Oct 2023

On affected Range Rover vehicles fitted with V8 Gasoline NC11 engines the fixings used to secure the engine mounted oil cooler hoses have been found to have inadequate thread engagement.

Fix: Vehicles will have the engine oil cooler pipe fixings inspected and replaced if required.

67 vehicles · built 4 Sep 2023 to 20 Oct 2023

For certain vehicles the bolt connecting the busbar to the traction battery module connector has not achieved the required clamp force. Arcing at the joint and excessive heat generation cannot be ruled out with the consequence that this may lead to a vehicle fire.�

Fix: Replacement of the High Voltage battery

2 vehicles · built 6 Jan 2023 to 8 Feb 2023

On certain 2014 - 2016 Model Year Land Rover Range Rover vehicles the front suspension upper knuckle joint could develop a crack. In extreme cases where a crack in the front suspension knuckle has developed this may lead to detachment of the upper suspension arm.�

Fix: Carry out an inspection of the front suspension knuckles and replace parts if required.�

• RANGE ROVER: 4,507 vehicles · built 1 Oct 2014 to 31 Mar 2015
• RANGE ROVER: 2,796 vehicles · built 2 Nov 2015 to 16 Mar 2016

On affected 2022 - 2023 Model Year Land Rover Range Rover vehicles the external rear lamp mounted in the body could partially or permanently fail to operate resulting in one or more of the light sources not working.

Fix: Affected vehicles will have the foam block mounted in the bodyshell removed. The rear lamp mounted in the body and rear tail lamp link lead wiring will be checked for their condition. Where the lamp and wiring are qualified OK no further remedy is required. Where the lamp or wiring are qualified Not OK the lamp will be replaced.

5,299 vehicles · built 23 Sep 2020 to 29 Nov 2022

On affected vehicles the second row 60% seat frame may have a latch installed with a defective weld. In vehicles that have a defective weld on the second row 60% seat frame latch the seat may not be correctly secured.

Fix: The rear seat base latch will be inspected. Where the inspection reveals a not OK condition the rear seat 60% frame and associated components will be replaced.

192 vehicles · built 8 Dec 2021 to 6 Jul 2022

For certain 2023 Model Year 3.0L AJ20-P6 Land Rover Range Rover Range Rover Sport Range Rover Velar Discovery and Defender vehicles a small number of engines the cam carrier oil gallery hasn�t been fully drilled. As a result the oil channel could be blocked leading to accumulation of oil against the pressure control valve rubber membrane and subsequently an external oil leak or increased oil carryover into the air intake system.

Fix: The engine cam carrier will be inspected and where an incorrectly machined cam carrier is found replace it with a correctly machined component. Depending on mileage and engine conditions further associated components may require replacement.

499 vehicles · built 24 Aug 2022 to 9 Jan 2023

On affected vehicles there is a risk where the water pump pully drive belt can become damaged leading to detachment or destruction. Where water pump pully drive is lost this leads to a loss coolant flow in the engine.

Fix: Affected vehicles will have the engine coolant elbow replaced. In addition a turbocharger feed coolant pipe will be replaced.

18,151 vehicles · built 6 Apr 2017 to 10 Dec 2021

Some of the hot end exhaust bracket fixings may not have been fastened or not have been fastened to the required torque.

Fix: Check for the presence of the exhaust bracket fixings and where necessary install new fixings or tighten existing fixings to the specified torque.

1,392 vehicles · built 25 Sep 2020 to 7 Jun 2022

The front crash sensor fixings may not have been installed to the specified level of torque.

Fix: Check and tighten the front crash sensor fixing to the specified level of torque.

254 vehicles · built 29 Nov 2021 to 31 Mar 2022

The Exhaust Gas Recirculation (EGR) crossover pipe may have been manufactured away from specification.

Fix: Check and repair the vehicle with a part manufactured to the correct specification.

144 vehicles · built 27 Aug 2020 to 29 Sep 2020

The routing of the electrical harness within the steering column assembly has insufficient clearance.

Fix: Inspect the steering column electrical harness apply further protective material and repair damaged wiring where required.

38 vehicles · built 15 Feb 2019 to 20 Feb 2019

The crankshaft pulley retaining bolt may fracture due to a production specification error.

Fix: Replace the crankshaft pulley centre retaining bolt with one that has been manufactured to the correct specification.

219 vehicles · built 10 Oct 2018 to 19 Dec 2018

The directional indicators may fail to operate.

Fix: Update the vehicle with the latest software on affected vehicles.

2,331 vehicles · built 10 Nov 2017 to 18 Dec 2018

Autonomous Emergency Braking (AEB) feature will not be available.

Fix: On affected vehicles download the latest software to the vehicle.

24 vehicles · built 13 Nov 2017 to 17 Mar 2018

On certain 2018 and 2019 Model Year Land Rover Range Rover and Range Rover Sport PHEV vehicles where the indicated fuel level on the fuel gauge shows approximately 30% the fuel tank is empty resulting in an engine stall. The vehicle will enter into reduced performance mode and if the customer continues to drive the vehicle will continue to run for circa 8 miles/13Km. The vehicle engine will then cut out without warning. If the traction battery charge status is at least 10% or greater the electric motor will take up drive until such time as traction battery power is depleted. Where the traction battery charge status is below 10% drive from the electric motor is not possible and the vehicle will cut out whilst in motion. All 12 volt powered electrical functions such as power assisted steering exterior lighting and brake assistance will continue to operate as designed. Engine cut out with minimal warning to the driver may lead to an increased risk of an accident.

Fix: Fit a new revised fuel level sensor float to the vehicle.

1,000 vehicles · built 28 Mar 2017 to 25 May 2018

The brazing of the fuel rail end caps is inconsistent and may not correctly seal the fuel rail ends. Fuel vapour and liquid fuel leaks can occur over time. This can lead to a liquid fuel leak into the engine bay.

Fix: On affected vehicles replace the fuel rail with a correctly manufactured version.

1,537 vehicles · built 5 May 2016 to 31 Jan 2018

Due to a software issue the Instrument cluster may intermittently go blank.

Fix: Affected vehicles will be recalled to have the latest software installed/downloaded.

14,932 vehicles · built 4 Sep 2016 to 17 Aug 2017

The Emergency Locking Retractor in the front passenger safety belt assembly may not function correctly. The Emergency Locking Retractors are equipped with a vehicle-sensitive locking mechanism and a webbing-sensitive locking mechanism. The vehicle-sensitive locking mechanism may not lock as designed. In the event of a pre-crash brake event where the passenger airbag deploys front passenger seat forward facing child seat occupants may sustain more severe injuries.

Fix: Recall the vehicles that are likely to be affected and replace the left hand front seat belt assembly.

5,170 vehicles · built 12 Apr 2016 to 31 Oct 2016

The front passenger airbag may not function properly due to a deviation in generant mix ratio. In the event of a crash of sufficient severity the front passenger airbag may not deploy when required. Failure to deploy can lead to increased injuries to the passenger seat occupant.

Fix: Recall the vehicles that are likely to be affected and replace the front passenger airbag.

139 vehicles · built 20 Sep 2016 to 25 Oct 2016

It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to non-deployment of the air-bag. Should a collision occur then there is an increased risk of injury to the passenger.

Fix: Recall all affected vehicles to replace the air-bag with a new quality assured component.

452 vehicles · built 12 Jul 2016 to 26 Oct 2016