Nissan Juke recalls

On affected vehicles the front seat belt may have been accidentally damaged during the parts preparation for assembly.

Fix: The retailers will inspect vehicles as identified as potentially affected and replace any affected seat belt assemblies.

4,342 vehicles · built 2 Apr 2024 to 6 Sep 2024

On affected vehicles the VIN stored in the vehicle system may not match the actual VIN of the vehicle. This may lead to a situation where a vehicle user can see information related to a different vehicle resulting in a data security breach.

Fix: Replace the navigation display / control unit and the telematics control unit.

2 vehicles · built 14 Oct 2019 to 1 Jun 2023

On affected vehicles the right-hand rear door welds may be out of specification. The door may rattle and a side impact may increase the risk of deformation. In the extreme impact could cause the hinge to fail and the door to open.

Fix: Replace the rear right-hand door.

8 vehicles · built 14 Nov 2023 to 20 Nov 2023

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

Fix: Update the HEVC module software

3,157 vehicles · built 16 Jun 2022 to 14 Dec 2022

The rear seat back may not be securely latched when returned to the upright position after folding.

Fix: Replace both rear seat lock knobs with a countermeasure part.

13,569 vehicles · built 18 Sep 2019 to 28 Aug 2020

The drivers� bag may tear during inflation.

Fix: Replace the drivers� airbag of all potentially affected vehicles.

7,095 vehicles · built 4 Apr 2019 to 30 May 2019

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 3 Mar 2018

Ignition Switch spring defect may cause engine to be turned off while driving

Fix: Inspect and where necessary replace the Ignition Switch

1,046 vehicles · built 3 Apr 2017 to 13 Jun 2017

If an electrical short occurs in the supply to the rear oxygen sensor the senor will fail but the driver will not see an immediate warning. A MIL warning may display after continued driving depending on driving/vehicle characteristics.

Fix: Reprogram the ECU to display a warning if the rear oxygen sensor fails.

7,393 vehicles · built 5 Jun 2014 to 25 May 2016

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

Fix: Inspect and where necessary modify the push start switch housing.

10,248 vehicles · built 26 Jun 2013 to 1 May 2014

On affected vehicles the fuel pressure sensor may not have been tightened to the correct specification. Heat and engine vibration may cause the sensor to loosen and in extreme cases allow fuel to leak.

Fix: Tighten fuel pressure sensor on affected vehicles

3,489 vehicles · built 25 Jan 2012 to 6 May 2014

In the event that the driver airbag is deployed during a frontal impact small holes may occur on the surface of the airbag. The holes are caused by high temperature gases from the airbag inflator exhausting directly onto the surface of the airbag material. The high temperature gas/airbag material may contact the drivers skin. The deployment performance of the driver airbag is not affected.

Fix: To replace the driver airbag with new.

2,498 vehicles · built 7 Jun 2012 to 4 Jul 2012

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

Fix: Re-tighten the pressure sensor and replace the pressure sensor gasket if required.

4,690 vehicles · built 8 Mar 2010 to 30 Jan 2012

The Turbocharger boost sensor bracket may separate from the air inlet tube. This means the boost pressure may be measured incorrectly and the engine warning lamp may be illuminated. During low-speed driving this could cause the engine to stall and not restart

Fix: Inspect and if necessary replace the air inlet tube with a new one

2,741 vehicles · built 8 Mar 2010 to 14 Nov 2011

It is possible that the vehicles brake fluid maybe contaminated with mineral oil. This can cause the seals within the system to swell and affect their sealing properties. This may require drivers to apply additional force to the foot brake and could increase stopping distances.

Fix: Recall affected vehicles to have the system flushed and replenished with clean fluid.

69 vehicles · built 8 Nov 2010 to 9 Nov 2010