Nissan Navara recalls

On affected vehicles the manufacturer will increase the maximum target efficiency of the SCR system in online dosing mode to further improve the emissions of the vehicle.

Fix: Update the software of the AdBlue Dosing Control Module.

28,292 vehicles · built 18 May 2016 to 10 May 2019

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 14 Mar 2018

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 6 Jan 2004 to 2 Mar 2012

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 6 Jan 2004 to 2 Mar 2012

It has been identified that under certain unusual conditions the High Mounted Stop Lamp (HMSL) fitted to Navara accessory hardtops does not illuminate simultaneously with the vehicle's stop lamps. During engine start it is possible that a voltage drop can occur which may fall below the HMSL operating threshold. This may result in HMSL not illuminating following engine start.

Fix: Recall all affected vehicles to modify wiring and the supply to the HMSL.

5,560 vehicles · built 1 Oct 2015 to 16 Jun 2016

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 6 Jan 2004 to 30 Mar 2007

Incorrect installation of the front seat belts has occurred where the position of the left hand side and right hand side seat belts may have been swapped. This incorrect installation affects homologation regulation and may potentially affect restraint performance.

Fix: Recall the vehicles that are likely to be affected to check and where necessary refit the front seat belts.

310 vehicles · built 20 Aug 2013 to 30 Sep 2013

The front lower suspension/steering ball joint retaining ring may not have been manufactured to specification. This could in extreme circumstances result in the detachment of the ball joint from its housing. This can then cause loss of control of the vehicle.

Fix: Recall all affected vehicles to check and if required replace the lower link ball joint.

471 vehicles · built 29 Aug 2013 to 27 Sep 2013

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 22 May 2001 to 25 Dec 2003

The Drivers power seat harness may become trapped between the metal seat bracket and the seat lifter Mechanism. If the vehicle continues to be driven in this condition damage to the harness may occur and this can result in loss of operation of the driver's power seat. In extreme circumstances unexpected self-operation of the driver's power seat base may occur.

Fix: Inspection of the driver's power seat harness for correct installation rectify if necessary. If the harness is damaged it will be replaced with new.

29,866 vehicles · built 30 May 2005 to 29 Sep 2009

In certain rare conditions where the vehicle is used fully loaded and cornering with high lateral acceleration a crack may occur on the spoke of the aluminium wheel. If this condition is ignored and the vehicle continues to be driven the crack may propagate around other wheel spokes. This condition is expected to create a change in the vehicle handling and in extreme cases could lead to wheel detachment.

Fix: Recall the vehicles that are likely to be affected to replace the wheels.

35,630 vehicles · built 1 Jun 2005 to 3 Jul 2008

The clevis pin may displace from the brake pedal/brake booster input rod assembly as the clevis pin securing clip may not have been fitted at the factory.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit a clevis pin securing clip.

125 vehicles · built 1 Feb 2010 to 3 Mar 2010

A concern has been identified relating to the incorrect assembly of the rear axle. This may result in excessive wear of the wheel bearings which will lead to noise occurring from the rear axle. If this is not rectified the bearing may ultimately fail resulting in the assembly becoming detached from the axle.

Fix: Recalled vehicles will be checked and fitted with new halfshafts as required.

5,812 vehicles · built 1 May 2005 to 31 Dec 2005

A concern has been identified relating to the fitment of the steering shaft lower joint. Should the joint become detached steering control will be lost.

Fix: Recalled vehicles will have the subject joint inspected and the clamp bolt will be renewed if required.

7,812 vehicles · built 1 Feb 2005 to 31 Jan 2006

Insufficient torque may have been applied to the propshaft securing bolts during production and this could lead to vibration. If the concern is not rectified the propshaft may detach from the vehicle.

Fix: Affected vehicles will be recalled and inspected if necessary the propshaft securing bolts will be replaced.

5,107 vehicles · built 1 Feb 2005 to 30 Sep 2005

A potential welding concern with the lock support of the engine hood has been identified which if ignored could result in the hood not being secured when closed.

Fix: Recalled vehicles will have the hood replaced with a quality assured part.

34 vehicles · built 31 Mar 2005 to 9 Apr 2005