Nissan recalls

For affected vehicles an incorrect Emissions Label may have been installed . As a result the label does not accurately reflect the vehicle’s actual emissions.

Fix: Replace the Emissions Label with the correct European specification label.

108 vehicles · built 13 Jan 2026 to 27 Jan 2026

For affected vehicles an incorrect Emissions Label may have been installed . As a result the label does not accurately reflect the vehicle’s actual emissions.

Fix: Replace the Emissions Label with the correct European specification label.

26 vehicles · built 13 Jan 2026 to 27 Jan 2026

For affected vehicles there is an issue involving the E power Battery Management system (BMS) where warnings and entering limp mode or loss of power cannot be ruled out. Vehicle will not return to normal function until power-latch (IGN off for approximately 30 mins and key away from vehicle).

Fix: Reprogram the Battery Management System (BMS).

15,592 vehicles · built 8 Jul 2025 to 20 May 2026

For affected vehicles the lithium-ion battery controller (LBC) on some X-Trail (T33) vehicles may not properly maintain diagnostic robustness. It has been found that these ICs may misdiagnose abnormalities and as a result the system may enter fail-safe mode during driving which restricts motor output and prohibits charging. Under certain conditions a loss of motive power may occur and the vehicle may stop while driving due to the loss of propulsion.

Fix: Update to the Battery Management Software (BMW)

21,835 vehicles · built 1 Dec 2021 to 21 Apr 2026

For affected vehicles the AdBlue Dosing Module may not have been initialised during the production process. In this condition the AdBlue Dosing Module does not trigger AdBlue injection and therefore NOx emissions are not controlled.

Fix: The AdBlue dosing control module (ADCM) activation status will be checked. If it is not active the AdBlue Injector will be replaced and the AdBlue Dosing Control Module activated.

1,116 vehicles · built 22 Nov 2016 to 24 Apr 2025

For affected vehicles the tyre size has been incorrectly configured in some of the control units. In this condition the calculation of the vehicle speed for display is made using incorrect data. As a result the vehicle displays a calculated vehicle speed that is 2% lower than the actual speed of the vehicle.

Fix: Reconfigure the Body Control Module (BCM) Anti-Lock braking System (ABS) and Front Camera with the correct tyre size.

373 vehicles · built 26 Feb 2025 to 5 Sep 2025

For certain vehicles the end-stop breaking force of the accelerator pedal is lower than the intended technical specification. This may lead to a rupture of the accelerator pedal assembly if the pedal is pressed vigorously.

Fix: Replacement of the accelerator pedal assembly.

2,160 vehicles · built 18 Sep 2024 to 26 Aug 2025

For certain vehicles the end-stop breaking force of the accelerator pedal is lower than the intended technical specification. This may lead to a rupture of the accelerator pedal assembly if the pedal is pressed vigorously.

Fix: Replacement of the accelerator pedal assembly.

239 vehicles · built 18 Sep 2024 to 26 Aug 2025

For affected vehicles there is concern that the left side headlamp beam may be out of alignment.

Fix: The left side head lamp beam will be adjusted according to specification

148 vehicles · built 14 Mar 2022 to 24 Feb 2025

For affected vehicles it has been identified that there is potential for movement between the fuel pipe and its retaining clip within the engine bay this movement can potentially lead to wear on the fuel pipe. In an extreme situation this may cause a hole in the fuel pipe resulting in a potential fuel leak.

Fix: Carry out an inspection of the fuel pipe and If identified wear is within limits apply protective Grommet to fuel tube. If wear is judged to be outside acceptable limits or a fuel leak from the fuel pipe is identified replace the fuel pipe.

101,557 vehicles · built 4 May 2021 to 17 Oct 2024

For affected vehicles there is a risk of head contact with the rear door latch. Due to the sharp edges of the door latch there is a risk of injury when head contact occurs.

Fix: Installation of a cover to the striker bar to protect the customer from the sharp edge.

6,405 vehicles · built 5 Feb 2021 to 16 May 2025

For affected vehicles the back door hinge pins may have been incorrectly assembled during production. In this condition the back door hinge pin may be missing.

Fix: Carry out an inspection of the rear door hinges and replace if found to be defective.

31 vehicles · built 29 Oct 2024 to 29 Oct 2024

For affected vehicles there is an issue involving the steering gear for where damage or cracking cannot be ruled out. The consequences are that loss of assistance or in some cases loss of control.

Fix: Replacement of the steering rack and supporting components.

2 vehicles · built 25 Sep 2024 to 25 Mar 2025

For affected vehicles due to a software concern the calculated and displayed battery state of charge may rapidly fluctuate.

Fix: Reprograming of the battery management system with the latest software.

20,847 vehicles · built 22 Sep 2021 to 9 Jan 2024

On affected vehicles the front seat belt may have been accidentally damaged during the parts preparation for assembly.

Fix: The retailers will inspect vehicles as identified as potentially affected and replace any affected seat belt assemblies.

4,342 vehicles · built 2 Apr 2024 to 6 Sep 2024

On affected vehicles the Adaptive LED Headlight (ALH) configuration may be out of specification. In this condition the ALH may not function as intended and alternate between high and low beam mode despite the presence of other vehicles.

Fix: Update the adaptive LED headlights (ALH) control module software configuration with revised parameters.

2,246 vehicles · built 15 Jan 2024 to 1 Oct 2024

For certain vehicles due to incorrect software calibration the Intelligent Speed Assistance may not behave as intended.

Fix: Reconfigure the associated control units to address the issue.

187 vehicles · built 2 Jul 2024 to 27 Sep 2024

On certain vehicles Fuel Pipe characteristics may be out of specification and may have insufficient clearance between fuel pipe and engine harness.

Fix: Check of the fuel inlet pipe replacing if necessary and installing a rigid spacer on the pipe.

238 vehicles · built 26 Aug 2014 to 27 Sep 2023

On affected vehicles the airbag side impact sensors may not have been installed during production. Additionally some vehicles may lack the required wire harnesses for connection of the side impact sensors.

Fix: Installation of side impact sensors and where required associated cable kits.

184 vehicles · built 20 Feb 2021 to 24 Nov 2023

On affected vehicles an oil seal within the traction motor may leak causing a malfunction resulting in the traction motor going into failsafe and traction torque reducing to zero.

Fix: Replace the traction motor.

126 vehicles · built 12 May 2022 to 21 Jun 2023

On affected vehicles the VIN stored in the vehicle system may not match the actual VIN of the vehicle. This may lead to a situation where a vehicle user can see information related to a different vehicle resulting in a data security breach.

Fix: Replace the navigation display / control unit and the telematics control unit.

2 vehicles · built 14 Oct 2019 to 1 Jun 2023

On affected vehicles the VIN stored in the vehicle system may not match the actual VIN of the vehicle. This may lead to a situation where a vehicle user can see information related to a different vehicle resulting in a data security breach.

Fix: Replace the navigation display / control unit and the telematics control unit.

1 vehicles · built 14 Oct 2019 to 1 Jun 2023

On affected vehicles the VIN stored in the vehicle system may not match the actual VIN of the vehicle. This may lead to a situation where a vehicle user can see information related to a different vehicle resulting in a data security breach.

Fix: Replace the navigation display / control unit and the telematics control unit.

1 vehicles · built 14 Oct 2019 to 1 Jun 2023

On affected vehicles the right-hand rear door welds may be out of specification. The door may rattle and a side impact may increase the risk of deformation. In the extreme impact could cause the hinge to fail and the door to open.

Fix: Replace the rear right-hand door.

8 vehicles · built 14 Nov 2023 to 20 Nov 2023

The incorrect specification of intercooler has been used for production (Euro6D instead of Euro6E).

Fix: The intercooler will receive replacement with a compliant component.

201 vehicles · built 7 Jun 2023 to 2 Oct 2023

The incorrect specification of intercooler has been used for production (Euro6D instead of Euro6E).

Fix: The intercooler will receive replacement with a compliant component.

Vehicle count not given · built 7 Jun 2023 to 2 Oct 2023

On affected vehicles the capacitive mat for hand on detection may have been damaged during manufacture of the steering wheel.� The steering wheel may falsely detect the driver has their hands on the wheel with ProPilot engaged and not give a warning to place hands back on the wheel.�

Fix: Inspect the steering wheel serial number and replace with a new countermeasure part where necessary.�

9,536 vehicles · built 6 May 2021 to 27 Sep 2022

On affected vehicles there is a potential for conductive fibrous shavings from the drive motors� slip ring assembly to momentarily cause a short circuit between the two slip rings.

Fix: Update the software of the Inverter ECM with software that has been modified to reset instantly in the event of a short circuit detection.

3,538 vehicles · built 9 Mar 2022 to 5 Apr 2023

On affected vehicles the manufacturer will increase the maximum target efficiency of the SCR system in online dosing mode to further improve the emissions of the vehicle.

Fix: Update the software of the AdBlue Dosing Control Module.

28,292 vehicles · built 18 May 2016 to 10 May 2019

On affected vehicles the child lock function on the rear door locks may be out of specification. The child lock may become disengaged when the inside door handle is operated.

Fix: Replace the rear door lock assemblies on both sides with a countermeasure part.

4 vehicles · built 28 Mar 2022 to 31 Mar 2022

A potential concern affecting the Vehicle Control Module (VCM) logic of some vehicles has been identified whereby in specific and rare circumstances after switching off the cruise control function there is a possibility of unintended acceleration.

Fix: The software of the VCM will be updated.

37,574 vehicles · built 17 Dec 2017 to 30 May 2023

In certain vehicles should the driver�s seat be set in the position where it coincides with a design feature�in the upper rail it may�in certain conditions exceed the stress limits of the rail material.

Fix: Replace the seat slide rails with countermeasure parts.�

41,191 vehicles · built 5 Dec 2016 to 5 Oct 2021

On affected vehicles a potential software concern may result in the combination meter screen intermittently switching OFF for 5 seconds and then switching back ON.�

Fix: Over The Air (OTA) software update sent to customers vehicle updating the combination meter software only.�

770 vehicles · built 20 Apr 2022 to 23 Aug 2022

A potential concern affecting the HEVC (Hybrid Electric Vehicle Control) module software has been identified which may cause a module reset of affected vehicles. Simultaneous pressing of brake and accelerator could cause engine stumble or stall.

Fix: Update the HEVC module software

3,157 vehicles · built 16 Jun 2022 to 14 Dec 2022

The torque value given in the Repair bulletin for R/2022/254 for the injector clamp bolts was insufficient. Under specific driving conditions this can cause the leakage of exhaust gasses past the injector sealing washer.

Fix: Replace all injector sealing washers retaining plates bolts and pipes as necessary and tighten with the correct torque.

78 vehicles · built 8 Dec 2001 to 16 Feb 2022

The injectors may not have been correctly torqued during assembly. Under specific driving conditions this can cause the leakage of exhaust gasses past the injector sealing washer.

Fix: Replace all injector washers retainers and retaining bolts with new parts and tighten to correct torque.

14 vehicles · built 15 Feb 2022 to 16 Feb 2022

Potential fuel ingress into a piezo-electric actuator unit within the fuel injectors.

Fix: Replace the injector/s with a countermeasure part.

292 vehicles · built 6 Dec 2021 to 2 Mar 2022

Some steering rack trial parts were reintroduced into the normal production process.

Fix: Replace the steering rack with a countermeasure part.

7 vehicles · built 16 Sep 2021 to 29 Sep 2021

The rear seat back may not be securely latched when returned to the upright position after folding.

Fix: Replace both rear seat lock knobs with a countermeasure part.

13,569 vehicles · built 18 Sep 2019 to 28 Aug 2020

The Right-Hand Rear Brake Caliper could fail during an activation of the parking brake.

Fix: Inspect and where necessary replace right hand rear brake caliper.

67 vehicles · built 10 Feb 2021 to 26 Feb 2021

The incorrect weight information was applied to the Certificate of Conformity (COC).

Fix: To proactively update the Certificate of Conformity (COC) and replace the vehicle registration document of all potentially affected vehicles.

10 vehicles · built 19 Mar 2020 to 29 Sep 2020

The steering knuckles may deform affecting the steering performance.

Fix: Replace the front knuckle steering at both sides of all potentially affected vehicles.

2 vehicles · built 20 Aug 2020 to 16 Oct 2020

Contact of the fuel supply pipe with the cylinder head cover causing pipe wear.

Fix: Carry out a visual inspection of the fuel supply pipe and fit a pipe protector. If necessary replace the fuel supply pipe.

1,448 vehicles · built 2 Jan 2018 to 25 Apr 2019

The drivers� bag may tear during inflation.

Fix: Replace the drivers� airbag of all potentially affected vehicles.

7,095 vehicles · built 23 Apr 2019 to 19 Nov 2019

The drivers� bag may tear during inflation.

Fix: Replace the drivers� airbag of all potentially affected vehicles.

7,095 vehicles · built 4 Apr 2019 to 30 May 2019

The welded joint on the park lock actuator plate may be of poor quality and has the potential to fail during usage.

Fix: Replace the park lock actuator plate with a countermeasure part of all potentially affected vehicles

2,547 vehicles · built 19 Jul 2019 to 22 Sep 2019

The welded joint on the park lock actuator plate may be of poor quality and has the potential to fail during usage.

Fix: Replace the park lock actuator plate with a countermeasure part of all potentially affected vehicles

2,547 vehicles · built 18 Jul 2019 to 9 Sep 2019

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 13 Aug 2016

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 3 Mar 2018

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 3 Mar 2018

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 14 Mar 2018

Possible reduced retention force of the Rear Door Child Lock switch.

Fix: Fit a countermeasure part into the child lock door switch aperture of all potentially affected vehicles.

299,631 vehicles · built 28 Sep 2015 to 14 Mar 2018

The rear brake caliper handbrake lever pivot pin may break during handbrake operation

Fix: Inspect and where necessary replace the rear brake caliper with a countermeasure part

33 vehicles · built 29 Mar 2019 to 6 Jun 2019

The rear brake caliper assembly fixings may have been insufficiently tightened

Fix: Proactively confirm the rear brake caliper assembly torques and where necessary replace parts

144 vehicles · built 14 Aug 2019 to 3 Sep 2019

Passenger air bag may not deploy correctly..

Fix: Replace passenger air bag inflator

2 vehicles · built 19 Jul 2001 to 6 Nov 2003

Incorrect permissible front axle figures were given on the VIN label.

Fix: Replace VIN label with new

12 vehicles · built 14 Aug 2019 to 3 Sep 2019

The masses applied on the VIN label may be incorrect.

Fix: Replace VIN label with new.

1,985 vehicles · built 17 Jul 2018 to 5 Nov 2018

The torque applied to right rear leaf spring U-bolts may not be as per specification

Fix: Inspect and where necessary rework the right rear leaf spring assembly

12 vehicles · built 3 May 2018 to 10 Jul 2018

The passenger airbag may develop a tear during deployment.

Fix: Replace the passenger airbag with new countermeasure parts

12,119 vehicles · built 1 Oct 2016 to 14 Nov 2017

The hand brake cable stopper may have been incorrectly formed in production and may fail.

Fix: Replace the handbrake cable and bracket with countermeasure parts

181 vehicles · built 18 May 2018 to 13 Sep 2018

A fuel tank that may not meet required material wall thickness specification

Fix: Check and replace the fuel tank if necessary

1 vehicles · built 7 Mar 2019 to 14 Mar 2019

The radiator fan assembly motor controller may have a ceramic capacitor fitted that can potentially fail.

Fix: Replace radiator fan assembly with a countermeasure part.

10,240 vehicles · built 6 Jun 2018 to 14 Nov 2018

Rear door child lock function in the Owner�s Manual incorrectly indicates the locked & unlocked positions

Fix: Place addendum in the Owner's Manual correcting the lock and unlock position of the rear child lock.

5,036 vehicles · built 18 Aug 2015 to 15 Jan 2018

Rear door child lock function in the Owner�s Manual incorrectly indicates the locked & unlocked positions

Fix: Place addendum in the Owner's Manual correcting the lock and unlock position of the rear child lock.

5,036 vehicles · built 18 Aug 2015 to 15 Jan 2018

Engine Control Module (ECM) identification label does not contain the certification number on the label.

Fix: Attach correct ECM label to affected vehicles.

2 vehicles · built 26 Mar 2018 to 20 Jul 2018

Engine Control Module (ECM) identification label does not contain the certification number on the label.

Fix: Attach correct ECM label to affected vehicles.

2 vehicles · built 26 Mar 2018 to 20 Jul 2018

Ignition Switch spring defect may cause engine to be turned off while driving

Fix: Inspect and where necessary replace the Ignition Switch

1,046 vehicles · built 3 Apr 2017 to 13 Jun 2017

Ignition Switch spring defect may cause engine to be turned off while driving

Fix: Inspect and where necessary replace the Ignition Switch

43 vehicles · built 30 Mar 2017 to 29 May 2017

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 6 Jan 2004 to 24 Dec 2012

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 12 Jan 2004 to 28 Nov 2006

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 7 Jan 2004 to 21 Nov 2005

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 4 Jan 2004 to 24 Nov 2006

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 6 Jan 2004 to 2 Mar 2012

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Fix: Replace the front passenger airbag inflator with a new dessicated type.

27,623 vehicles · built 10 Jan 2004 to 28 Nov 2012

Warning light not coming on with steering fault

Fix: Software upgrade

16 vehicles · built 1 Mar 2017 to 11 Nov 2017

Due to an incorrect software setting of the Body Control Module (BCM) the system may not trigger a warning (double speed flashing) in the case of a direction indicator lamp failure.

Fix: On affected vehicles reprogram the Body Control Module.

10,791 vehicles · built 12 Jun 2017 to 15 Jan 2018

VIN label contains incorrect Gross Combination Weight (GCW) information for manual and CVT vehicles.

Fix: On affected vehicles replace the VIN label with a new one showing the correct information.

8,385 vehicles · built 5 Jun 2017 to 5 Oct 2017

The front wheel hub may suffer cracking. Drivers may notice abnormal noise and in extreme cases the hub may fail.

Fix: On affected vehicles check manufacturing date of the wheel hubs and replace if required.

14 vehicles · built 26 Sep 2017 to 4 Oct 2017

The Steering column may become detached from the rack due to incorrectly tightened bolt

Fix: On affected vehicles check for presence of retaining nut. If present tighten nut to specified torque. If nut is absent replace bolt and screw and tighten to specified torque. THE MANUFACTURER HAS ADVISED NOT TO DRIVE THE VEHICLE.

41 vehicles · built 12 May 2016 to 6 Jun 2017

The fuel filter support bracket may crack and the fuel filter could become insecure As a result the fuel filter and or fuel tube may leak.

Fix: On affected vehicles replace the fuel filter support bracket Check condition of filter and fuel tube. Replace if necessary

25 vehicles · built 1 Dec 2016 to 2 Feb 2017

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 4 Jan 2004 to 24 Nov 2006

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 7 Jan 2004 to 24 Nov 2005

The door mirror indicator repeater may not operate as intended when the heated rear screen is switched on.

Fix: On affected vehicles inspect wiring and where necessaary rework the indicator connnections.

202 vehicles · built 12 Jun 2017 to 28 Jun 2017

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 6 Jan 2004 to 2 Mar 2012

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 12 Jan 2004 to 28 Nov 2006

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 10 Jan 2004 to 28 Nov 2012

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Fix: On affected vehicles replace air bag assembly.

39,318 vehicles · built 6 Jan 2004 to 24 Dec 2012

The subject vehicles are equipped with front passenger�airbag�inflators which could have been assembled with improperly manufactured propellant This could cause the inflator to rupture and the front passenger�airbag�to deploy abnormally in a crash. This could result in increased risk of injury to the occupant.

Fix: On affected vehicles replace the airbag with a new assembly.

124,482 vehicles · built 3 Aug 2005 to 19 Jul 2013

The subject vehicles are equipped with front passenger�airbag�inflators which could have been assembled with improperly manufactured propellant This could cause the inflator to rupture and the front passenger�airbag�to deploy abnormally in a crash. This could result in increased risk of injury to the occupant.

Fix: On affected vehicles replace the airbag with a new assembly.

124,482 vehicles · built 23 Jan 2007 to 21 Aug 2014

In conditions such as high speed and high vehicle loading the rear right wheel arch protector may contact the brake hose. Over time repeated contact could wear through the outer protective cover of the brake hose. This could damage the inner reinforcing braiding and in an extreme case wear a hole in the hose which could lead to brake fluid leakage.

Fix: On affected vehicles re-work the rear wheel arch protector and if necessary replace the brake pipe with new.

25,435 vehicles · built 23 Sep 2013 to 26 May 2016

The ignition switch harness connector of some Nissan Micra (K14 models) equipped with a mechanical key may not be correctly locked in position. As a result the connector may disconnect which in an extreme case could result in engine shut down while driving with no possibility to restart.

Fix: On affected vehicles inspect wiring harness and where necessary rework the ignition switch retaining latch.

1,615 vehicles · built 23 May 2016 to 14 Apr 2017

Due to a non confromity in production the headlamp auto aim function may not operate

Fix: Reconfigure and then reinitialise the headlamp leveliser control unit on affected vehicles.

65 vehicles · built 12 Feb 2017 to 29 Mar 2017

The airbag manufacturer have informed Nissan of a potential concern with propellant degradation of Front Passenger Airbag fitted with Smokeless Passenger Inflator (SPI). It has been confirmed that this degradation is a function of time temperature and environmental moisture. Deterioration of the Inflator propellant may under certain usage conditions lead to abnormal deployment of the Passenger Airbag. In an extreme situation this condition could create excessive pressure within the inflator during airbag deployment and may result in separation of the airbag housing.

Fix: Recall all affected vehicles to replace the front passenger airbag module with a new quality controlled item.

9 vehicles · built 25 Aug 2001 to 31 Aug 2001

The airbag manufacturer have informed Nissan of a potential concern with propellant degradation of Front Passenger Airbag fitted with Smokeless Passenger Inflator (SPI). It has been confirmed that this degradation is a function of time temperature and environmental moisture. Deterioration of the Inflator propellant may under certain usage conditions lead to abnormal deployment of the Passenger Airbag. In an extreme situation this condition could create excessive pressure within the inflator during airbag deployment and may result in separation of the airbag housing.

Fix: Recall all affected vehicles to replace the front passenger airbag module with a new quality controlled item.

9 vehicles · built 7 Jun 2000 to 28 Aug 2001

An an incorrect maximum permissible vehicle width was incorrectly defined on the Certificate of Conformity (COC) documentation. Due to this a customer installing a body conversion according to that defined on the COC may inadvertently fit a body width that could restrict the rear visibility.

Fix: On affected vehciles measure the width of vehicle and where necessary fit extended mirrors

2,487 vehicles · built 3 Nov 2011 to 1 Mar 2016

It has been identified that due to a manufacturing issue the Anti-lock Braking System (ABS) Actuator Control Unit may have contamination within it. When in use the contamination particle can migrate within the ABS unit and become trapped in a valve. In this condition the ABS may not operate as per design intent in the worst case when the ABS is activated under certain unusual driving conditions the customer may experience wheel lock and the vehicle�s dynamic behaviour would be adversely affected.

Fix: Recall all affected vehicles to inspect the ABS control unit and where necessary replace it with new component.

197 vehicles · built 15 Apr 2016 to 29 Apr 2016

It has been identified that under certain unusual conditions the High Mounted Stop Lamp (HMSL) fitted to Navara accessory hardtops does not illuminate simultaneously with the vehicle's stop lamps. During engine start it is possible that a voltage drop can occur which may fall below the HMSL operating threshold. This may result in HMSL not illuminating following engine start.

Fix: Recall all affected vehicles to modify wiring and the supply to the HMSL.

5,560 vehicles · built 1 Oct 2015 to 16 Jun 2016

Due to an error in production cracks may form in the steering wheel. This could compromise the strength of the steering wheel and in extreme conditions may detach.

Fix: On affected vehicles inspect the steering wheel and replace where necessary.

19 vehicles · built 25 Sep 2012 to 14 Dec 2013

The paint coating applied to the back door gas stay does not comply with the design requirement for anti-corrosion. Therefore the outer tube of the gas stay may corrode and crack resulting in the loss of the pressurised gas inside the gas stay. In this condition the gas stay would be unable to support the opening of the back door allowing it to drop on the vehicle user.

Fix: Recall the vehicles that are likely to be affected and replace the back door gas stay.

4,377 vehicles · built 1 Aug 2009 to 27 Nov 2015

The paint coating applied to the back door gas stay does not comply with the design requirement for anti-corrosion. Therefore the outer tube of the gas stay may corrode and crack resulting in the loss of the pressurised gas inside the gas stay. In this condition the gas stay would be unable to support the opening of the back door allowing it to drop on the vehicle user.

Fix: Recall the vehicles that are likely to be affected and replace the back door gas stay.

4,377 vehicles · built 1 Apr 2014 to 25 Dec 2015

The paint coating applied to the back door gas stay does not comply with the design requirement for anti-corrosion. Therefore the outer tube of the gas stay may corrode and crack resulting in the loss of the pressurised gas inside the gas stay. In this condition the gas stay would be unable to support the opening of the back door allowing it to drop on the vehicle user.

Fix: Recall the vehicles that are likely to be affected and replace the back door gas stay.

4,377 vehicles · built 1 Apr 2014 to 4 Mar 2016

If an electrical short occurs in the supply to the rear oxygen sensor the senor will fail but the driver will not see an immediate warning. A MIL warning may display after continued driving depending on driving/vehicle characteristics.

Fix: Reprogram the ECU to display a warning if the rear oxygen sensor fails.

7,393 vehicles · built 24 Apr 2014 to 16 May 2016

If an electrical short occurs in the supply to the rear oxygen sensor the senor will fail but the driver will not see an immediate warning. A MIL warning may display after continued driving depending on driving/vehicle characteristics.

Fix: Reprogram the ECU to display a warning if the rear oxygen sensor fails.

7,393 vehicles · built 10 Apr 2015 to 7 Jun 2016

If an electrical short occurs in the supply to the rear oxygen sensor the senor will fail but the driver will not see an immediate warning. A MIL warning may display after continued driving depending on driving/vehicle characteristics.

Fix: Reprogram the ECU to display a warning if the rear oxygen sensor fails.

7,393 vehicles · built 5 Jun 2014 to 25 May 2016

If an electrical short occurs in the supply to the rear oxygen sensor the senor will fail but the driver will not see an immediate warning. A MIL warning may display after continued driving depending on driving/vehicle characteristics.

Fix: Reprogram the ECU to display a warning if the rear oxygen sensor fails.

7,393 vehicles · built 23 Sep 2014 to 26 May 2016

The turbocharger oil pipe ferrule material may have cracked during its forming process. In this condition there is a risk that the oil pipe may lose its sealing resulting in the leakage of oil from the vehicle. Depending on the severity of the leak and the vehicle conditions oil could contact hot areas in the engine room possibly resulting in fire.

Fix: Recall the vehicles that are likely to be affected and replace the turbocharger oil pipe.

4 vehicles · built 18 Sep 2015 to 26 Oct 2015

On affected vehicles with Pulsar headlight auto levelling the initialisation process during production was incorrect. In this condition affected vehicles may not correctly adjust the height of the headlamp aim when the rear of the vehicle is heavily laden and therefore may not comply with the specific regulation requirements

Fix: Reprogram the Intelligent Power Distribution Module (IPDM) and re-initialise the headlamp auto-levelling system.

8,404 vehicles · built 22 May 2014 to 21 Dec 2015

The engine ignition coil may not be to the correct specification. The internal electrical components of the coil may short circuit resulting in an engine misfire. In the worst case this short circuit may cause a fuse inside the Power Distribution Module (IPDM) to fail stopping power to the ignition relay. In this condition the engine may stall and prevent the customer from being able to restart the engine.

Fix: Recall the vehicles that are likely to be affected and replace the ignition coil with new.

2,010 vehicles · built 6 Aug 2015 to 11 Jan 2016

The engine ignition coil may not be to the correct specification. The internal electrical components of the coil may short circuit resulting in an engine misfire. In the worst case this short circuit may cause a fuse inside the Power Distribution Module (IPDM) to fail stopping power to the ignition relay. In this condition the engine may stall and prevent the customer from being able to restart the engine.

Fix: Recall the vehicles that are likely to be affected and replace the ignition coil with new.

2,010 vehicles · built 9 Jul 2015 to 5 Jan 2016

In the event of driver�s airbag deployment the internal pressure of inflator may increase abnormally and in an extreme case cause the driver�s airbag inflator casing to rupture. In an extreme case this may cause a scattering of metal fragments.

Fix: Owners will be advised that their vehicle is affected by the recall and will be contacted again when parts are available and the driver's air bag will be replaced..

124,507 vehicles · built 30 Aug 2005 to 31 Dec 2011

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 6 Jan 2004 to 30 Mar 2007

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 7 Jan 2004 to 21 Nov 2005

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 12 Jan 2004 to 28 Nov 2006

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 4 Jan 2004 to 24 Nov 2006

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 6 Jan 2004 to 30 Mar 2007

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Fix: Inspect air bag assembly and where required replace air bag inflator

99,525 vehicles · built 10 Jan 2004 to 30 Mar 2007

The lower pinion needle bearing may have been omitted during manufacture of the steering gear due to insufficient controls in the suppliers manufacturing process. It is possible the pinion may disengage from the steering gear with loss of steering control.

Fix: On affected vehicles inspect and where necessary replace rack.

6,973 vehicles · built 27 Jun 2008 to 7 Oct 2008

The lower pinion needle bearing may have been omitted during manufacture of the steering gear due to insufficient controls in the suppliers manufacturing process. It is possible the pinion may disengage from the steering gear with loss of steering control.

Fix: On affected vehicles inspect and where necessary replace rack.

6,973 vehicles · built 27 Jun 2008 to 3 Sep 2008

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

Fix: Inspect and where necessary modify the push start switch housing.

10,248 vehicles · built 5 Jun 2013 to 16 Mar 2015

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

Fix: Inspect and where necessary modify the push start switch housing.

10,248 vehicles · built 26 Jun 2013 to 1 May 2014

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

Fix: Inspect and where necessary modify the push start switch housing.

10,248 vehicles · built 10 Sep 2013 to 6 Jan 2014

On affected models with a push start ignition switch the switch may remain in the pressed position and not return after switching the engine on. If the vehicle continues to be driven in this condition the emergency engine stop function may operate and cause the engine to unintentionally stop.

Fix: Inspect and where necessary modify the push start switch housing.

10,248 vehicles · built 1 Jul 2013 to 3 Mar 2014

The engine ECM unit may have an error with its software. This could under certain exceptional engine start circumstances result in the ECM setting an incorrect engine throttle valve position. When the engine speed is in excess of 3600 rpm the customer may briefly experience an unexpected acceleration. However the driver can counter this by applying the brakes.

Fix: Recall all affected vehicles to install new software.

3,806 vehicles · built 25 Oct 2010 to 27 Feb 2015

On affected vehicles the fuel pressure sensor may not have been tightened to the correct specification. Heat and engine vibration may cause the sensor to loosen and in extreme cases allow fuel to leak.

Fix: Tighten fuel pressure sensor on affected vehicles

3,489 vehicles · built 25 Jan 2012 to 6 May 2014

It has been identified that due to the incorrect assembly of the driver airbag inflator. If the vehicle is involved in a collision and the air bag is required to deploy then the gas flow path may have been blocked increasing the internal pressure within the inflator. As a result the driver airbag inflator casing may crack and fragment.

Fix: Recall all affected vehicle to inspect and where necessary replace driver airbag with a quality assured item.

1,919 vehicles · built 27 May 2010 to 31 Jul 2012

It is possible that the steering wheel boss may not have been produced to the correct specification. If a higher than normal loading is applied to the steering wheel typically on low speed manoeuvring it is possible that the steering wheel boss may separate from the steering column. This can result in a loss of steering control.

Fix: Recall all affected vehicles to check and if necessary replace the steering wheel assembly.

27,252 vehicles · built 17 Feb 2012 to 30 Jul 2012

A fail safe clip on the steering column may have become dislodged during the assembly process. As a result the column may not have been correctly assembled. Over a period of time and under certain conditions the column may work loose and disconnect causing a loss of steering.

Fix: On affected vehicles inspect column and where necessary replace the column shaft.

4,474 vehicles · built 12 Feb 2013 to 16 Oct 2014

The bolted joints fixing the towbar kit to the chassis of the vehicle may loosen. In an extreme situation where the vehicle continues to be driven with loose bolted joints the towbar kit may detach from the vehicle.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary rework the towbar kit.

43,238 vehicles · built 19 Jul 2013 to 17 Oct 2014

Incorrect installation of the front seat belts has occurred where the position of the left hand side and right hand side seat belts may have been swapped. This incorrect installation affects homologation regulation and may potentially affect restraint performance.

Fix: Recall the vehicles that are likely to be affected to check and where necessary refit the front seat belts.

310 vehicles · built 20 Aug 2013 to 30 Sep 2013

Incorrect installation of the front seat belts has occurred where the position of the left hand side and right hand side seat belts may have been swapped. This incorrect installation affects homologation regulation and may potentially affect restraint performance.

Fix: Recall the vehicles that are likely to be affected to check and where necessary refit the front seat belts.

310 vehicles · built 20 Aug 2013 to 30 Sep 2013

The front lower suspension/steering ball joint retaining ring may not have been manufactured to specification. This could in extreme circumstances result in the detachment of the ball joint from its housing. This can then cause loss of control of the vehicle.

Fix: Recall all affected vehicles to check and if required replace the lower link ball joint.

471 vehicles · built 29 Aug 2013 to 27 Sep 2013

The front lower suspension/steering ball joint retaining ring may not have been manufactured to specification. This could in extreme circumstances result in the detachment of the ball joint from its housing. This can then cause loss of control of the vehicle.

Fix: Recall all affected vehicles to check and if required replace the lower link ball joint.

471 vehicles · built 29 Aug 2013 to 27 Sep 2013

It has been identified that the accelerator pedal position sensor located in the accelerator pedal assembly may provide an incorrect signal due to sensor terminal wear. If this occurs the ECM will detect the sensor failure and illuminate the engine management waning lamp on the dash. It will also control and` limit vehicle acceleration. However in extreme case if this situation occurs and there is excessive dust in the throttle valve which could affect the amount of intake air then the engine could stall at idle speed.

Fix: Recall all affected vehicles and replace the throttle pedal assembly.

113 vehicles · built 25 Aug 2006 to 28 Nov 2009

It is possible that the heater fan motor may seize at slow speed. Under extreme conditions this may cause the internal temperature of the heater fan circuit to increase. If this occurs the thermal fuse may not cut-out which will result in an overheating of the fan and its surrounding area. The driver will find smoke being exhaled via the heater vents and in extreme circumstances there could be a vehicle fire.

Fix: Recall all affected vehicles and replace the heater motor thermal fuse with an up-rated item.

14,548 vehicles · built 3 Nov 2008 to 22 Jun 2012

It is possible that the steering wheel mounting bolt may not have been torqued to the correct specification. In addition this torque setting may deteriorate over time as axial tension on the steering wheel boss can be affected by temperature change. The driver will receive warning of the issue by the excessive play/movement in the steering wheel. However should the driver neglect to take notice of this warning it is possible that the steering wheel could detach and affect direction control of the vehicle.

Fix: Recall all affected vehicle check the torque and if required re-torque the steering wheel bolt.

133,869 vehicles · built 2 Dec 2002 to 12 May 2006

The brake master cylinder piston/plunger outer surface is not to specification. This can result in an issue with the internal seals in the cylinder which can cause longer brake pedal travel under light braking. In extreme cases braking efficiency maybe affected.

Fix: Recall all affected vehicles and replace the brake master cylinder.

8,288 vehicles · built 1 Jun 2012 to 15 Mar 2013

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 7 Jan 2004 to 21 Nov 2005

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 6 Jan 2003 to 28 Feb 2004

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 12 Jan 2004 to 28 Nov 2006

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 22 Aug 2001 to 28 Feb 2004

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 22 May 2001 to 31 Dec 2003

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 22 Aug 2001 to 25 Dec 2003

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 4 Jan 2004 to 24 Nov 2006

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 2 Jul 2001 to 25 Dec 2003

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 22 May 2001 to 25 Dec 2003

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 19 Feb 2001 to 25 Dec 2003

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

59,008 vehicles · built 28 Aug 2001 to 25 Dec 2003

In the event that the driver airbag is deployed during a frontal impact small holes may occur on the surface of the airbag. The holes are caused by high temperature gases from the airbag inflator exhausting directly onto the surface of the airbag material. The high temperature gas/airbag material may contact the drivers skin. The deployment performance of the driver airbag is not affected.

Fix: To replace the driver airbag with new.

2,498 vehicles · built 7 Jun 2012 to 4 Jul 2012

The engine bay insulation for right hand drive vehicles equipped with 2.0 l diesel engine (M9R) engine may have insufficient clearance from the turbocharger. In extreme cases this may cause the insulation to smoulder due to the high temperature of the turbocharger.

Fix: Recall the vehicles that are likely to be affected to fit an additional bracket to position the engine bay insulation away from the turbocharger.

14,025 vehicles · built 21 Dec 2006 to 27 Apr 2012

It is possible that the steering wheel boss may not have been produced to the correct specification. If a higher than normal loading is applied to the steering wheel in its normal operation it is possible that the steering wheel boss may separate from the steering column. This can result in a loss of steering control.

Fix: Recall all affected vehicles to check and if necessary replace the steering wheel assembly.

7,329 vehicles · built 27 Feb 2012 to 20 Apr 2012

It is possible that the steering wheel boss may not have been produced to the correct specification. If a higher than normal loading is applied to the steering wheel in its normal operation it is possible that the steering wheel boss may separate from the steering column. This can result in a loss of steering control.

Fix: Recall all affected vehicles to check and if necessary replace the steering wheel assembly.

7,329 vehicles · built 27 Feb 2012 to 16 May 2012

The fuel filter hose connector may not be fully connected to the fuel filter. If the vehicle continues to be driven in this condition a fuel leak may occur or in extreme conditions the engine may stall.

Fix: Recall all affected vehicles and inspect the fuel filter hose connector. If found to be faulty carry out remedial work.

796 vehicles · built 5 Sep 2011 to 5 Jan 2012

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

Fix: Re-tighten the pressure sensor and replace the pressure sensor gasket if required.

4,690 vehicles · built 8 Mar 2010 to 30 Jan 2012

Nissan has identified that the fuel rail pressure sensor of some vehicles may have not been correctly tightened to the fuel rail of the engine and may loosen gradually due to heat and vibration of the engine. If left undetected and the vehicle continues to be driven in this condition in extreme cases fuel leakage may occur.

Fix: Re-tighten the pressure sensor and replace the pressure sensor gasket if required.

4,690 vehicles · built 25 Jan 2011 to 29 Dec 2011

The Drivers power seat harness may become trapped between the metal seat bracket and the seat lifter Mechanism. If the vehicle continues to be driven in this condition damage to the harness may occur and this can result in loss of operation of the driver's power seat. In extreme circumstances unexpected self-operation of the driver's power seat base may occur.

Fix: Inspection of the driver's power seat harness for correct installation rectify if necessary. If the harness is damaged it will be replaced with new.

29,866 vehicles · built 30 May 2005 to 29 Sep 2009

The Drivers power seat harness may become trapped between the metal seat bracket and the seat lifter Mechanism. If the vehicle continues to be driven in this condition damage to the harness may occur and this can result in loss of operation of the driver's power seat. In extreme circumstances unexpected self-operation of the driver's power seat base may occur.

Fix: Inspection of the driver's power seat harness for correct installation rectify if necessary. If the harness is damaged it will be replaced with new.

29,866 vehicles · built 1 Nov 2004 to 5 Nov 2009

It has been established that the casting for the heat sink on the Electric Power Steering (EPS) control unit may be out of specification. In extreme cases this can cause a failure of the EPS motor which will illuminate a warning light on the dash. Whilst directional control is not affected it is possible that the driver will experience a sudden loss of power assistance.

Fix: Recall all affect vehicles and replace the EPS control unit.

2,693 vehicles · built 6 Aug 2010 to 12 Aug 2011

The Turbocharger boost sensor bracket may separate from the air inlet tube. This means the boost pressure may be measured incorrectly and the engine warning lamp may be illuminated. During low-speed driving this could cause the engine to stall and not restart

Fix: Inspect and if necessary replace the air inlet tube with a new one

2,741 vehicles · built 8 Mar 2010 to 14 Nov 2011

It has been established that the casting for the heat sink on the Electric Power Steering (EPS) control unit may be out of specification. In extreme cases this can cause a failure of the EPS motor which will illuminate a warning light on the dash. Whilst directional control is not affected it is possible that the driver will experience a sudden loss of power assistance.

Fix: Recall all affect vehicles and replace the EPS control unit.

2,693 vehicles · built 6 Aug 2010 to 12 Aug 2011

In certain rare conditions where the vehicle is used fully loaded and cornering with high lateral acceleration a crack may occur on the spoke of the aluminium wheel. If this condition is ignored and the vehicle continues to be driven the crack may propagate around other wheel spokes. This condition is expected to create a change in the vehicle handling and in extreme cases could lead to wheel detachment.

Fix: Recall the vehicles that are likely to be affected to replace the wheels.

35,630 vehicles · built 1 Jun 2005 to 3 Jul 2008

Risk that the primary handbrake cable end - piece crimping may not conform so the handbrake cable may become detached.

Fix: Check crimping at cable end. Replace cable if not within tolerance.

118 vehicles · built 19 May 2010 to 23 Aug 2010

It is possible that the vehicles brake fluid maybe contaminated with mineral oil. This can cause the seals within the system to swell and affect their sealing properties. This may require drivers to apply additional force to the foot brake and could increase stopping distances.

Fix: Recall affected vehicles to have the system flushed and replenished with clean fluid.

69 vehicles · built 8 Nov 2010 to 9 Nov 2010

It is possible that the vehicles brake fluid maybe contaminated with mineral oil. This can cause the seals within the system to swell and affect their sealing properties. This may require drivers to apply additional force to the foot brake and could increase stopping distances.

Fix: Recall affected vehicles to have the system flushed and replenished with clean fluid.

69 vehicles · built 8 Nov 2010 to 9 Nov 2010

It has been identified that it is possible that the contacts in engine control module (ECM) and ignition relay situationed in the Intelligent Power Distribution Module (IPDM) may become contaminated with silicon oxide due to the evaporating of the silicon from within the units. In extreme cases this could result in the stalling of the engine and the failure to restart the engine.

Fix: Recall all affected vehicles and replace the defective units.

83,777 vehicles · built 29 Jan 2004 to 28 Jun 2006

It has been identified that it is possible that the contacts in engine control module (ECM) and ignition relay situationed in the Intelligent Power Distribution Module (IPDM) may become contaminated with silicon oxide due to the evaporating of the silicon from within the units. In extreme cases this could result in the stalling of the engine and the failure to restart the engine.

Fix: Recall all affected vehicles and replace the defective units.

83,777 vehicles · built 29 Jan 2004 to 28 Jun 2006

It has been identified that the welds on the left-hand front suspension turret may fail. Should this occur the vehicle could tilt to the left-hand side and directional control could ultimately be affected.

Fix: Recall those affected vehicles for remedial work to be carried out on the suspension turret.

11 vehicles · built 27 Jul 2006 to 29 Jul 2006

The combustion rate of the airbag propellant may be too fast causing excessive internal pressure in the inflator during airbag deployment. In an extreme case the inflator casing may rupture leading to a scattering of metal fragments.

Fix: Recall the vehicles that are likely to be affected to replace the front passenger airbag assembly.

4 vehicles · built 23 Oct 2000 to 31 May 2001

The combustion rate of the airbag propellant may be too fast causing excessive internal pressure in the inflator during airbag deployment. In an extreme case the inflator casing may rupture leading to a scattering of metal fragments.

Fix: Recall the vehicles that are likely to be affected to replace the front passenger airbag assembly.

4 vehicles · built 25 Aug 2001 to 31 Aug 2001

The clevis pin may displace from the brake pedal/brake booster input rod assembly as the clevis pin securing clip may not have been fitted at the factory.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit a clevis pin securing clip.

125 vehicles · built 1 Feb 2010 to 3 Mar 2010

The clevis pin may displace from the brake pedal/brake booster input rod assembly as the clevis pin securing clip may not have been fitted at the factory.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit a clevis pin securing clip.

125 vehicles · built 1 Feb 2010 to 3 Mar 2010

The clevis pin may displace from the brake pedal/brake booster input rod assembly as the clevis pin securing clip may not have been fitted at the factory.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit a clevis pin securing clip.

125 vehicles · built 1 Feb 2010 to 3 Mar 2010

In some cases a higher electric current may cause the shift solenoid circuit contact in the stop lamp switch to burn/melt. Additionally the auto transmission selector may not move from the Park position

Fix: Recall affected vehicles and replace stop lamp switch.

646 vehicles · built 2 Mar 2009 to 11 Feb 2010

It has been identified that due to an engineering fault in production a dimensional variation has occurred to the fuel pump seating. This may result in a possible fuel leak from the pump seating area whilst the vehicle is being fuelled.

Fix: Recalled vehicles will have the fuel pump gasket and O replaced.

3,930 vehicles · built 2 Mar 2009 to 22 Aug 2009

It has been identified that there is the possibility in the event of an impact the potential insecurity of the front right hand seat base mounting may result in the seat detaching from the floor thus affecting occupant safety.

Fix: Recalled vehicles will have the right hand front seat base brackets welded to the correct specification.

271 vehicles · built 22 Feb 2008 to 18 May 2009

There is a possibility that the lower steering column connecting rod may become disconnected resulting in loss of steering control.

Fix: Recall affected vehicles to check and if necessary retorque steering rod bolts.

1,858 vehicles · built 25 Aug 2008 to 23 Oct 2008

The cover screw securing the pinion shaft may loosen causing noise during steering operation. Continued use in this condition could result in the screw coming out of the gear housing and in certain circumstances cause a loss of steering control.

Fix: Recall the potentially affected vehicles to fit a locking plate to the cover screw that secures the pinion shaft.

58,342 vehicles · built 24 Nov 2006 to 14 Jul 2009

The cover screw securing the pinion shaft may loosen causing noise during steering operation. Continued use in this condition could result in the screw coming out of the gear housing and in certain circumstances cause a loss of steering control.

Fix: Recall the potentially affected vehicles to fit a locking plate to the cover screw that secures the pinion shaft.

58,342 vehicles · built 4 Nov 2006 to 4 Jun 2009

The rear seat belt buckle retaining bolt may become loose resulting in buckle becoming detached

Fix: Recall affected vehicles check and refit retorque and lock bolt.

129 vehicles · built 20 Dec 2002 to 12 Mar 2008

It has been identified that the air intake duct on VQ23/35DE engines may become detached from the intermediate resonator of the engine's air intake system. This can result in unstable idling poor acceleration or engine stall whilst driving

Fix: Recalled vehicles will have the subject air intake duct replaced.

2,539 vehicles · built 17 Oct 2002 to 11 Jan 2008

It has been identified that the air intake duct on VQ23/35DE engines may become detached from the intermediate resonator of the engine's air intake system. This can result in unstable idling poor acceleration or engine stall whilst driving

Fix: Recalled vehicles will have the subject air intake duct replaced.

2,539 vehicles · built 17 Oct 2002 to 11 Jan 2008

It has been identified that the driver's airbag on some K12 Micras due to incorrect welding of the airbag module may not deploy in the event of a frontal impact. Thus potentially reducing the protection afforded to the vehicle's occupants.

Fix: Recalled vehicles will have the subject airbag replaced.

67 vehicles · built 17 Sep 2008 to 22 Oct 2008

It has been identified that the possibility exists that the intermediate handbrake connector may break resulting in the cable potentially separating from the connector. The possibility then exists that parking brake functionality would be lost.

Fix: Recalled vehicles will have the subject connector replaced.

7,373 vehicles · built 1 Jan 2006 to 10 Jun 2008

It has been identified that a connector in the diesel particulate filter fuel system may not be correctly attached. If this is ignored fuel may leak from the connector during a particulate filter regeneration cycle.

Fix: Recalled vehicles will have the connector checked and tightened as necessary.

45 vehicles · built 4 Jan 2008 to 28 Oct 2008

It has been identified that a connector in the diesel particulate filter fuel system may not be correctly attached. If this is ignored fuel may leak from the connector during a particulate filter regeneration cycle.

Fix: Recalled vehicles will have the connector checked and tightened as necessary.

45 vehicles · built 4 Jan 2008 to 28 Oct 2008

The incorrect side airbag may deploy in the event of an accident.

Fix: Recall the vehicles that are likely to be affected to replace the airbag control unit with one containing the correct logic.

2 vehicles · built 1 Jul 2006 to 30 Nov 2006

There is a possibility that the air conditioning compressor may seize which could result in an unexpected engine stall.

Fix: Recall the vehicles that are likely to be affected to replace the a/c compressor and the drive belt and idler roller.

10 vehicles · built 6 Nov 2006 to 5 Jan 2007

It has been identified that if the vehicle's ignition switch is off and the hazard lights are on they will not illuminate on any trailer attached to the vehicle.

Fix: Recalled vehicles will be fitted with a sub-harness.

4,309 vehicles · built 1 Mar 2007 to 30 Apr 2008

It has been identified that the possibility exists that a needle bearing has been omitted from the steering shaft. Additionally the cover screw may not have been tightened to the correct torque. This may result in the cover screw becoming loose initiating free play and noise within the steering system. Ultimately steering control may be lost.

Fix: Recalled vehicles will have the steering gear inspected. The steering gear will be replaced should this be found to be necessary.

9,362 vehicles · built 1 Nov 2006 to 30 Jun 2007

There is a possibility that a steering cover screw may not be sufficiently tight. This could lead to initially free play and noise in the steering which if not attended to eventually could result in the loss of steering control.

Fix: Recall the vehicles that are likely to be affected to inspect and where necessary replace the steering gear.

182 vehicles · built 25 Jun 2007 to 30 Jun 2007

It has been identified that the possibility exists that a needle bearing has been omitted from the steering shaft. Additionally the cover screw may not have been tightened to the correct torque. This may result in the cover screw becoming loose initiating free play and noise within the steering system. Ultimately steering control may be lost.

Fix: Recalled vehicles will have the steering gear inspected. The steering gear will be replaced should this be found to be necessary.

9,362 vehicles · built 1 Mar 2007 to 30 Jun 2007

The engine may stall as a result of the crank shaft position sensor wiring harness being incorrectly routed and possibly coming into contact with the blades of the cooling fan.

Fix: Recall the vehicles that are likely to be affected to check the wiring harness and re-route or replace the wiring harness as necessary.

28 vehicles · built 1 Jul 2006 to 30 Jun 2007

There is a possibility that a rear wheel bearing may have been overtightened at the factory. If ignored this condition could result in reduced bearing life and ultimately the bearings could fail.

Fix: Recall the vehicles that are likely to be affected to replace the rear wheel bearings.

184 vehicles

A concern has been detected in relation to the passenger seat cushion anchorage of some F24 Cabstar vehicles. If ignored the condition could result in a potential for the seat occupant to not be fully restrained in the case of a vehicle collision.

Fix: Recalled vehicles will have the (potentially) missing seat retaining bolt fitted.

6 vehicles · built 27 Jul 2006 to 7 Mar 2007

It has been identified that the front suspension lower ball joints on some of the subject vehicles have not been fully seated into the hub. This has resulted in the securing bolt not fitting into the groove in the ball joint shank. If the situation goes uncorrected the ball joint could detach which could result in loss of vehicle control.

Fix: Recalled vehicles will be checked for correct location of the ball joint and rectified as necessary.

945 vehicles · built 12 Feb 2007 to 5 Mar 2007

It has been identified that the parking brake levers situated on the rear disc calipers may have a fissure. This carries the potential risk that loss of parking brake function may occur due to the levers breaking.

Fix: Recalled vehicles will be inspected and affected parts replaced as necessary.

118 vehicles · built 1 Oct 2005 to 1 Jan 2006

A concern has been identified with the rear seat ISOFIX brackets of some E11 Note vehicles. In that the brackets may have been manufactured incorrectly with the potential that the brackets may not perform to the design intent in the case of a side impact. In addition the brackets may not conform to the required EC legislation.

Fix: Recalled vehicles will have the subject seat brackets replaced.

338 vehicles · built 25 Jan 2006 to 3 Feb 2006

There is a possibility that the fuel tank filler tube may rust around the mounting bracket. This may create a small hole through progression of rust and fuel may leak during the refuelling process.

Fix: Recalled vehicles will have the fuel filler tube replaced.

27,869 vehicles · built 1 Jun 2000 to 23 Nov 2004

In the event of a front tyre travelling over a sharp object the object could be propelled towards the rear of the vehicle and possibly damage the front edge of the fuel tank.

Fix: Recalled vehicles will have a protective shield fitted to the fuel tank vulnerable area.

1,684 vehicles · built 1 Apr 2002 to 30 Nov 2005

There is a possibility that during a frontal impact and under specific circumstances the rear seat belt webbing may be damaged. This could increase the risk of injury to an occupant during an impact.

Fix: Recalled vehicles will have a protector fitted to the affected seat belt area.

1,434 vehicles · built 1 Apr 2002 to 1 Jul 2005

There is a possibility that during a frontal impact and under specific circumstances the rear seat belt webbing may be damaged. This could increase the risk of injury to an occupant during an impact.

Fix: Recalled vehicles will have a protector fitted to the affected seat belt area.

1,434 vehicles · built 1 Apr 2002 to 31 Jul 2005

In the event of a front tyre travelling over a sharp object the object could be propelled towards the rear of the vehicle and possibly damage the front edge of the fuel tank.

Fix: Recalled vehicles will have a protective shield fitted to the fuel tank vulnerable area.

1,684 vehicles · built 1 Apr 2002 to 30 Nov 2005

A concern has been identified relating to the incorrect assembly of the rear axle. This may result in excessive wear of the wheel bearings which will lead to noise occurring from the rear axle. If this is not rectified the bearing may ultimately fail resulting in the assembly becoming detached from the axle.

Fix: Recalled vehicles will be checked and fitted with new halfshafts as required.

5,812 vehicles · built 1 May 2005 to 31 Dec 2005

A concern has been identified relating to the fitment of the steering shaft lower joint. Should the joint become detached steering control will be lost.

Fix: Recalled vehicles will have the subject joint inspected and the clamp bolt will be renewed if required.

7,812 vehicles · built 1 Feb 2005 to 31 Jan 2006

A concern has been identified relating to the fitment of the steering shaft lower joint. Should the joint become detached steering control will be lost.

Fix: Recalled vehicles will have the subject joint inspected and the clamp bolt will be renewed if required.

7,812 vehicles · built 1 Feb 2005 to 31 Jan 2006

Insufficient torque may have been applied to the propshaft securing bolts during production and this could lead to vibration. If the concern is not rectified the propshaft may detach from the vehicle.

Fix: Affected vehicles will be recalled and inspected if necessary the propshaft securing bolts will be replaced.

5,107 vehicles · built 1 Feb 2005 to 30 Sep 2005

Insufficient torque may have been applied to the propshaft securing bolts during production and this could lead to vibration. If the concern is not rectified the propshaft may detach from the vehicle.

Fix: Affected vehicles will be recalled and inspected if necessary the propshaft securing bolts will be replaced.

5,107 vehicles · built 1 Feb 2005 to 30 Sep 2005

A potential welding concern with the lock support of the engine hood has been identified which if ignored could result in the hood not being secured when closed.

Fix: Recalled vehicles will have the hood replaced with a quality assured part.

34 vehicles · built 31 Mar 2005 to 9 Apr 2005

A potential welding concern with the lock support of the engine hood has been identified which if ignored could result in the hood not being secured when closed.

Fix: Recalled vehicles will have the hood replaced with a quality assured part.

34 vehicles · built 31 Mar 2005 to 9 Apr 2005

The door locks may not latch correctly with the result that a door may open whilst the vehicle is being driven.

Fix: Recalled vehicles will have the right hand door locks replaced with quality assured items.

34,452 vehicles · built 1 Feb 2002 to 30 Sep 2002

A concern has been identified with the vacuum pump drive gear which could wear excessively due to insufficient surface hardness. If the condition is ignored gear wear could cause the pump to cease operating which results in the loss of brake assistance.

Fix: Subject vehicles will be recalled at which time the vacuum pump drive gear will be replaced.

105 vehicles · built 8 Dec 2002 to 6 Dec 2003

It is possible that the front lower portion of the cover on the front seat can become detached from its position. This can leave exposed a sharp metal edge on the seat base. This may cause injury or damage to the occupants hand when accessing the storage compartment or during seat adjustment.

Fix: Recall the affected vehicles and re-fit the cover with a modified fastener.

5,665 vehicles · built 11 Feb 2004 to 11 Mar 2004

It is possible that the front lower portion of the cover on the front seat can become detached from its position. This can leave exposed a sharp metal edge on the seat base. This may cause injury or damage to the occupants hand when accessing the storage compartment or during seat adjustment.

Fix: Recall the affected vehicles and re-fit the cover with a modified fastener.

5,665 vehicles · built 11 Feb 2004 to 11 Mar 2004

In certain cases the tightness of the steering wheel mounting may not conform to specification.

Fix: As a preventative measure likely to be affected vehicles will be recalled at which time the steering wheel will be replaced and it's mounting strengthened.

260 vehicles · built 9 Mar 2004 to 11 Mar 2004

The timing chain tensioner may become defective which can result in the timing chain jamming. Should this occur the engine may stall or fail to start. The condition may also result in the camshaft turning in a non-uniform fashion which could lead to the failure of the vacuum pump drive and a reduction in braking assistance.

Fix: Recalled vehicles will have the camshaft chain guide and tensioner replaced.

3,001 vehicles · built 1 Jul 1999 to 1 Dec 2002

The timing chain tensioner may become defective which can result in the timing chain jamming. Should this occur the engine may stall or fail to start. The condition may also result in the camshaft turning in a non-uniform fashion which could lead to the failure of the vacuum pump drive and a reduction in braking assistance.

Fix: Recalled vehicles will have the camshaft chain guide and tensioner replaced.

3,001 vehicles · built 1 Jul 1999 to 1 Dec 2002

A concern has been identified with the engine angle and position sensors of the engine management system If ignored it could cause the engine to stall and/or make it not possible to restart

Fix: Recall affected vehicles and replace sensors.

111,831 vehicles · built 1 Jan 1999 to 30 Sep 2002

A concern has been identified with the engine angle and position sensors of the engine management system If ignored it could cause the engine to stall and/or make it not possible to restart

Fix: Recall affected vehicles and replace sensors.

111,831 vehicles · built 1 Jan 1999 to 30 Sep 2002

A concern has been identified with the engine angle and position sensors of the engine management system If ignored it could cause the engine to stall and/or make it not possible to restart

Fix: Recall affected vehicles and replace sensors.

111,831 vehicles · built 1 Jan 1999 to 30 Sep 2002

A concern has been identified with the engine angle and position sensors of the engine management system If ignored it could cause the engine to stall and/or make it not possible to restart

Fix: Recall affected vehicles and replace sensors.

111,831 vehicles · built 1 Jan 1999 to 30 Sep 2002

The rear side seatbelt outer buckle may be of a material which has been incorrectly treated. The buckle may break in service. The seat belt would no longer offer a restraining facility

Fix: Recall affected vehicles and replace buckle with modified type

16,350 vehicles · built 1 May 2000 to 31 Dec 2002

The rear side seatbelt outer buckle may be of a material which has been incorrectly treated. The buckle may break in service. The seat belt would no longer offer a restraining facility

Fix: Recall affected vehicles and replace buckle with modified type

16,350 vehicles · built 1 May 2000 to 31 Dec 2002

In cold damp conditions the rear brake linings may swell and under light braking effort lock the rear wheels. This can adversely affect the vehicle's handling.

Fix: Fit improved specification brake linings.

1,796 vehicles · built 1 Sep 2001 to 17 Mar 2003

The steering wheel retaining bolt may not have been tightened to the specified torque. If ignored it can potentially lead to a loss of steering control.

Fix: Check the torque of the steering wheel retaining bolt and tighten where found necessary.

4,771 vehicles · built 1 Nov 2002 to 31 Mar 2003

A concern has been identified with the driver's seat walk-in device. If ignored it may cause unintended movement of the seat whilst driving.

Fix: Fit a modified component to the walk-in device mechanism.

3,961 vehicles · built 1 Dec 2002 to 28 Feb 2003

A conveyor used during vehicle manufacturing may have damaged the front left hand tyre. In extreme cases the damage could lead to possible deflation of the affected tyre.

Fix: Examine tyre for damage and replace where necessary.

2,758 vehicles

A conveyor used during vehicle manufacturing may have damaged the front left hand tyre. In extreme cases the damage could lead to possible deflation of the affected tyre.

Fix: Examine tyre for damage and replace where necessary.

2,758 vehicles

The front suspension transverse link rear pivot pin may break if subjected to an impact such as kerbing. Failure of the pivot pin would adversely affect the stability and safe control of the vehicle.

Fix: Fit new left and right hand suspension transverse links.

42 vehicles · built 1 Jun 2001 to 31 Jan 2002

An interference can occur between the steering column and the brake pipe which supplies fluid to the rear brakes which may lead to brake pipe leakage.

Fix: Recall affected vehicles and reposition brake pipe.

842 vehicles · built 1 Jul 2001 to 31 Mar 2002

The locating dowel on the parking brake assembly may become detached. In this case any impact on the lever may cause its unintended release.

Fix: Recall affected vehicles and fit a quality assured replacement parking brake assembly.

1,524 vehicles · built 1 Jun 2000 to 30 Jun 2001

Premature wear of the propshaft universal joint bearings may lead to noise vibration and eventual loss of drive.

Fix: Recall affected vehicles and fit a new propshaft which has improved bearings.

1,473 vehicles · built 1 Mar 2000 to 30 Jun 2001

The parking brake may not be able to be securely set due to misalignment of the ratchet and pawl teeth. In the worst case the parking brake may self release.

Fix: Recall affected vehicles and fit a quality assured replacement parking brake assembly.

19,240 vehicles · built 1 Dec 2000 to 30 Sep 2001

The parking brake may not be able to be securely set due to misalignment of the ratchet and pawl teeth. In the worst case the parking brake may self release.

Fix: Recall affected vehicles and fit a quality assured replacement parking brake assembly.

19,240 vehicles · built 1 Dec 2000 to 30 Sep 2001

A concern has been identified affecting 1.5 1.6 and 1.8 petrol engine crankshaft and camshaft position sensors (a common part). An internal failure of the component may cause the engine to stall and not restart.

Fix: Recall affected vehicles and fit a quality assured replacement crankshaft and camshaft position sensor.

40,455 vehicles · built 1 Mar 2000 to 31 Jul 2001

A concern has been identified affecting 1.5 1.6 and 1.8 petrol engine crankshaft and camshaft position sensors (a common part). An internal failure of the component may cause the engine to stall and not restart.

Fix: Recall affected vehicles and fit a quality assured replacement crankshaft and camshaft position sensor.

40,455 vehicles · built 1 Mar 2000 to 31 Jul 2001

A concern has been identified affecting 1.5 1.6 and 1.8 petrol engine crankshaft and camshaft position sensors (a common part). An internal failure of the component may cause the engine to stall and not restart.

Fix: Recall affected vehicles and fit a quality assured replacement crankshaft and camshaft position sensor.

40,455 vehicles · built 1 Mar 2000 to 31 Jul 2001

The side air bag satellite sensor may be incorrectly programmed. In the event of a collision the air bag may not deploy.

Fix: Recall affected vehicles and re-programme sensor.

761 vehicles · built 1 May 2000 to 30 Sep 2000

The brake system LSV pilot tube may chafe on the vehicle floorpan. Over time the wall thickness may reduce and allow fluid leakage resulting in reduced brake efficiency.

Fix: Recall affected vehicles and check LSV pilot tubes for chafing and either reposition or replace pipes.

4,905 vehicles · built 1 Jan 1995 to 31 Jul 1997

Under certain circumstances a front flexible brake hose may split leading to fluid loss and reduced brake performance.

Fix: Recall the affected vehicles for the fitment of modified front brake hoses.

74,000 vehicles · built 1 Jan 1990 to 31 Dec 1994

Minor cracking of the floor can occur around the handbrake lever mounting points. If this is ignored the effectiveness of the parking brake may be reduced.

Fix: Recall the subject vehicles and fit reinforcing plates to the affected floor area.

63,789 vehicles · built 1 Sep 1992 to 30 Jun 1994

Insufficient clearance between the ratchet internal mechanism and the handbrake lever sideplates may lead to misapplication of the parking brake resulting in the vehicle not being held.

Fix: Recall the affected vehicle for replacement of the original handbrake lever with a revised version.

1,542 vehicles · built 1 Jul 1992 to 31 May 1993

The security of the fuel filler hose to tube joint may be insufficient due to clip size and clamping capability. If ignored fuel leakage may occur.

Fix: Replace the original hose clip with an alternative version designed to increase the clamping effect on the hose.

8,578 vehicles · built 1 Aug 1992 to 31 Mar 1993