Renault recalls

There is a combined risk that rear axle hub nuts might have the tightening torque relaxed and the hub might not have been locked looked correctly. In the worst case it could lead the vehicle to lose a rear wheel set on road.

Fix: The current hub nut will be replaced by a new hub nut the specified torque will be applied and the nut will be crimped against the axle housing.

2 vehicles · built 18 Aug 2025 to 14 Dec 2025

Amendment to the Owners Handbook – Correction of an error in the operating instructions in paragraph 3.22 relating to the operation of the window lifter: incorrect description of the rear door locking procedure

Fix: Registered keeper will be sent a corrected page

5,126 vehicles · built 26 Apr 2016 to 11 Oct 2016

For certain vehicles and as a preventative measure there is concern involving the locking nuts in the area of the front suspension lower arm ball joints for where loosening of the fixings cannot be ruled out.

Fix: Check of the tightening of the front suspension lower arm ball joint nuts and if necessary replace both nuts

43 vehicles · built 18 Oct 2025 to 20 Oct 2025

On affected vehicles there is a risk of electric shock if the AC charging inlet socket (or the power cable to external equipment) is severely damaged and you touch an exposed electrical conducting part and at the same time touch the chassis or other earth connected part of the vehicle.

Fix: The insulation monitoring device (IMD) will be replaced by an upgraded version a residual current device (RCPF sensor) will be installed inside the insulation resistance measurement unit and software updated. If necessary some vehicles will have the EMC filter reinstalled.

29 vehicles · built 19 May 2025 to 8 Sep 2025

The AC inlet socket and the power outlet for body builder equipment might be incorrectly energized. It happens because these two features are not fully electrically isolated from each other. Therefore in vehicles where AC or DC power outlets are installed there might be voltage with low leakage current inadvertently present inside the AC inlet socket when the power outlet is active. Also when AC charging there might be a voltage with low leakage current inadvertently present on the power outlet .

Fix: Inspection and replacement of the Insulation Resistance Monitoring (IRM) Junction box.

10 vehicles · built 23 Oct 2023 to 18 Nov 2024

On affected vehicles due to a production nonconformity no AdBlue consumption is shown in the instrument cluster and therefore does not comply with the relevant regulations.

Fix: Activation of the Urea Dosing Module (UDM) check and if necessary replace the urea injector.

3,677 vehicles · built 16 Nov 2022 to 4 Jul 2024

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

256 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

76 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

25 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

1 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

1,042 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

579 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

102 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles there is a concern involving the accelerator pedal for where breakage cannot be ruled out.

Fix: Replacement of the accelerator pedal assembly.

29 vehicles · built 4 Nov 2024 to 25 Aug 2025

For certain vehicles reprogramming of the injection computer is required. Without this software update it could lead to breakdown or the vehicle failing to start.

Fix: Reprogramme the injection computer

16,996 vehicles · built 1 Sep 2022 to 11 Jul 2025

For certain vehicles reprogramming of the injection computer is required. Without this software update it could lead to breakdown or the vehicle failing to start.

Fix: Reprogramme the injection computer

22,972 vehicles · built 1 Sep 2022 to 11 Jul 2025

For certain vehicles reprogramming of the injection computer is required. Without this software update it could lead to breakdown or the vehicle failing to start.

Fix: Reprogramme the injection computer

12,500 vehicles · built 1 Sep 2022 to 11 Jul 2025

For certain vehicles the end-stop breaking force of the accelerator pedal is lower than the intended technical specification. This may lead to a rupture of the accelerator pedal assembly if the pedal is pressed vigorously.

Fix: Replacement of the accelerator pedal assembly.

4,850 vehicles · built 18 Sep 2024 to 29 Aug 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

7 vehicles · built 12 Apr 2024 to 7 May 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

16 vehicles · built 12 Apr 2024 to 7 May 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

23 vehicles · built 12 Apr 2024 to 7 May 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

11 vehicles · built 12 Apr 2024 to 7 May 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

40 vehicles · built 12 Apr 2024 to 7 May 2025

For certain vehicles a concern involving the electric traction reducer parking brake mechanism actuator or gearbox engagement actuator within the transmission may result in the parking brake mechanism actuator no longer correctly positioning the locking pawl in the “P lock”.

Fix: Replacement of the electric traction reducer parking brake mechanism actuator or gearbox Engagement Actuator.

3 vehicles · built 12 Apr 2024 to 7 May 2025

On certain vehicles the rear swing door strikers have a prominent character. Injuries may occur when entering or exiting from the rear of the vehicle (e.g. during loading or unloading).

Fix: The preventive measure is the addition of protective covers on the door strikers at the top of the two rear swing doors.

15,240 vehicles · built 15 May 2020 to 16 May 2025

For affected vehicles there is an issue involving the steering gear in the area of the torque sensor for where damage or cracking cannot be ruled out. The consequences are that loss of assistance or in some cases loss of control.

Fix: Replacement of the the steering box and the steering column intermediate shaft.

13 vehicles · built 30 Apr 2024 to 16 May 2025

On affected vehicles there is a risk of premature wear inside the gear selector switch. This could lead to the vehicle decelerating and moving backwards unintentionally without any command by the driver.

Fix: Fit a modified gear selector switch and install updated software.

87 vehicles · built 7 Sep 2020 to 3 Mar 2025

On affected vehicles there is a risk of premature wear inside the gear selector switch. This could lead to the vehicle decelerating and moving backwards unintentionally without any command by the driver.

Fix: Fit a modified gear selector switch and install updated software.

35 vehicles · built 7 Sep 2020 to 3 Mar 2025

There is a risk that a small metal piece from a broken terminal fixation might come loose and create a short circuit between battery cells inside the traction battery which might lead to overheating. There will be a red warning in the instrument cluster to the driver if a short-circuit is detected inside the battery before the battery overheats.

Fix: Replace Traction batteries

1 vehicles · built 22 Apr 2024 to 12 Aug 2024

There is a risk that a small metal piece from a broken terminal fixation might come loose and create a short circuit between battery cells inside the traction battery which might lead to overheating. There will be a red warning in the instrument cluster to the driver if a short-circuit is detected inside the battery before the battery overheats.

Fix: Replace Traction batteries

2 vehicles · built 22 Apr 2024 to 12 Aug 2024

There is a risk that a small metal piece from a broken terminal fixation might come loose and create a short circuit between battery cells inside the traction battery which might lead to overheating. There will be a red warning in the instrument cluster to the driver if a short-circuit is detected inside the battery before the battery overheats.

Fix: Replace Traction batteries

4 vehicles · built 14 Aug 2023 to 17 Feb 2025

For certain vehicles there is an issue involving the conformity of the four hinges of the rear doors for where a missing shaft cannot be ruled out.

Fix: Inspect the hinges and if required replace.

18 vehicles · built 18 Oct 2024 to 29 Oct 2024

On affected vehicles the accelerator pedal calibration is not working correctly which can cause the vehicle to accelerate at brake pedal release when selecting drive or reverse.

Fix: Update the accelerator pedal software.

9 vehicles · built 7 Sep 2020 to 15 Nov 2021

On affected vehicles the accelerator pedal calibration is not working correctly which can cause the vehicle to accelerate at brake pedal release when selecting drive or reverse.

Fix: Update the accelerator pedal software.

4 vehicles · built 7 Sep 2020 to 15 Nov 2021

On affected vehicles the rear stub axle material is not compliant to hardness specification. There is a risk the stub axle could break while driving.

Fix: Check the stub axle for cracks and replace if necessary.

9 vehicles · built 23 Sep 2024 to 7 Oct 2024

On affected vehicles there is a risk that the silencer may overheat when performing a regeneration which may result in a thermal event if there is excessive soot accumulated inside it

Fix: Install modified software.

3 vehicles · built 3 Feb 2014 to 5 Sep 2016

On affected vehicles there is a possible fault with the UDS Ad Blue pump which might cause it to lose efficiency and lead to the vehicle emissions being non-compliant.

Fix: Change the UDS pump for a modified version.

8 vehicles · built 17 Mar 2019 to 6 Sep 2021

On affected vehicles there is risk that a fuel hose may chafe against a wiring harness resulting in fuel leakage onto the engine which might cause smell of fuel inside the cabin excessive fuel consumption and a risk of a thermal event in the engine compartment.

Fix: Check fuel hose and replace if necessary and install a retainer.

148 vehicles · built 10 Nov 2014 to 10 May 2023

On affected vehicles there is risk that a fuel hose may chafe against a wiring harness resulting in fuel leakage onto the engine which might cause smell of fuel inside the cabin excessive fuel consumption and a risk of a thermal event in the engine compartment.

Fix: Check fuel hose and replace if necessary and install a retainer.

222 vehicles · built 31 Dec 2014 to 25 Mar 2023

On affected vehicles there is risk that a fuel hose may chafe against a wiring harness resulting in fuel leakage onto the engine which might cause smell of fuel inside the cabin excessive fuel consumption and a risk of a thermal event in the engine compartment.

Fix: Check fuel hose and replace if necessary and install a retainer.

34 vehicles · built 31 Dec 2014 to 6 Dec 2022

On affected vehicles there is risk that a fuel hose may chafe against a wiring harness resulting in fuel leakage onto the engine which might cause smell of fuel inside the cabin excessive fuel consumption and a risk of a thermal event in the engine compartment.

Fix: Check fuel hose and replace if necessary and install a retainer.

233 vehicles · built 12 Sep 2014 to 15 Aug 2024

On affected vehicles there is a possibility of abrasive wear of the fuel supply line. This can cause one or several possible effects: Fuel odour in the passenger compartment High fuel consumption Fuel leak in the engine compartment visible under the vehicle Risk of fire.

Fix: Check the fuel pipe and replace if required. All affected vehicles will be fitted with a mounting clip to protect the fuel pipe.

2,796 vehicles · built 23 Sep 2014 to 27 Sep 2024

On affected vehicles the electric motor support bracket screws could break allowing the electric motor to fall with risk of rupturing the power steering hydraulic hose resulting in a loss of steering power assistance.

Fix: Replacing fixing screws and support where necessary.

299 vehicles · built 1 Nov 2020 to 30 Jun 2023

On affected vehicles there is a potential risk the electrical powertrain may not be secured correctly.

Fix: Check and change the electric traction reducer mounting if necessary.

Vehicle count not given

On affected vehicles there is a potential risk the electrical powertrain may not be secured correctly.

Fix: Check and change the electric traction reducer mounting if necessary.

90 vehicles · built 29 Jul 2020 to 16 Jun 2023

When the easy access function is used on the front seats they may move and come in to contact with someone in the rear passenger seat possibility causing injury.

Fix: As a preventive measure the remedy consists of updating the configuration files of the front seats' computers.

3,620 vehicles · built 12 Apr 2022 to 28 Nov 2023

When the easy access function is used on the front seats they may move and come in to contact with someone in the rear passenger seat possibility causing injury.

Fix: As a preventive measure the remedy consists of updating the configuration files of the front seats' computers.

Vehicle count not given · built 12 Apr 2022 to 28 Nov 2023

Affected vehicles will not start and the traction battery cannot be recharged.

Fix: Check and change the traction battery if required.

52 vehicles · built 1 Jun 2022 to 30 Jun 2023

Affected vehicles will not start and the traction battery cannot be recharged.

Fix: Check and change the traction battery if required.

Vehicle count not given · built 1 Jun 2022 to 30 Jun 2023

On affected vehicles there is a possible short circuit in the traction battery which may generate a fire hazard.�

Fix: Check the traction battery compliance and replace if necessary.�

1 vehicles · built 20 Jun 2022 to 2 May 2023

On affected vehicles airbag sensors and brackets were not fitted on production. The airbags and seatbelt pre-tensioners will not be activated when needed.

Fix: Fit the missing components.

19 vehicles · built 1 May 2023 to 31 Dec 2023

On affected vehicles airbag sensors and brackets were not fitted on production. The airbags and seatbelt pre-tensioners will not be activated when needed.

Fix: Fit the missing components.

Vehicle count not given · built 1 May 2023 to 31 Dec 2023

On affected vehicles the driver and passenger airbag and seatbelt pre-tensioners may not deploy.

Fix: Replace the airbag collision sensors.�

22 vehicles · built 12 Sep 2023 to 17 Oct 2023

On affected vehicles the driver and passenger airbag and seatbelt pre-tensioners may not deploy.�

Fix: Replace the airbag collision sensors.�

1,135 vehicles · built 10 Nov 2021 to 4 Sep 2023

On affected vehicles there is a risk of damage to the wiper relay causing the wipers to stop working.

Fix: Update software and replace the relay.

1,800 vehicles · built 10 Sep 2021 to 19 Mar 2023

On affected vehicles there is a risk of damage to the wiper relay causing the wipers to stop working.

Fix: Update software and replace the relay.

1,800 vehicles · built 10 Sep 2021 to 19 Mar 2023

On affected vehicles there is a risk of damage to the wiper relay causing the wipers to stop working.

Fix: Update software and replace the relay.

1,800 vehicles · built 10 Sep 2021 to 19 Mar 2023

On affected vehicles there is a risk of damage to the wiper relay causing the wipers to stop working.

Fix: Update software and replace the relay.

1,800 vehicles · built 10 Sep 2021 to 19 Mar 2023

On affected vehicles there is a risk of corrosion in the steering extension shaft which might affect the steering manoeuvrability.

Fix: Replace the steering shaft with a new improved version.

9,999 vehicles · built 9 Sep 2013 to 4 Feb 2019

On affected vehicles there is a risk of corrosion in the steering extension shaft which might affect the steering manoeuvrability.

Fix: Replace the steering shaft with a new improved version.

9,999 vehicles · built 9 Sep 2013 to 4 Feb 2019

On affected vehicles there is a risk of corrosion in the steering extension shaft which might affect the steering manoeuvrability.

Fix: Replace the steering shaft with a new improved version.

9,999 vehicles · built 9 Sep 2013 to 4 Feb 2019

On affected vehicles there is a risk of corrosion in the steering extension shaft which might affect the steering manoeuvrability.

Fix: Replace the steering shaft with a new improved version.

9,999 vehicles · built 9 Sep 2013 to 4 Feb 2019

On affected vehicles the rear seat bench may not be locked into position securely. This could result in injury to the occupants in the event of hard breaking or a collision.

Fix: Check the rear seat bench has been securely locked in place.

440 vehicles · built 14 Nov 2022 to 3 Dec 2022

On affected vehicles there is a risk that some of the screws that attach the front axle to the suspension may become loose.

Fix: Check screws for the correct torque.

114 vehicles · built 9 Apr 2022 to 10 Dec 2022

On affected vehicles there is a risk that some of the screws that attach the front axle to the suspension may become loose.

Fix: Check screws for the correct torque.

114 vehicles · built 9 Apr 2022 to 10 Dec 2022

On affected vehicles there is a risk that some of the screws that attach the front axle to the suspension may become loose.

Fix: Check screws for the correct torque.

114 vehicles · built 9 Apr 2022 to 10 Dec 2022

The power cable from the battery box to the cab and engine might be damaged by chafing.

Fix: Check the routing of the cable and re-route if necessary.

58 vehicles · built 1 Jun 2019 to 31 Aug 2022

The power cable from the battery box to the cab and engine might be damaged by chafing.

Fix: Check the routing of the cable and re-route if necessary.

58 vehicles · built 1 Jun 2019 to 31 Aug 2022

Risk of fuel leakage due to incorrect machining of the fuel injection bar.

Fix: Replace the fuel injection bar.

3 vehicles

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number. Depending on the identification number on the part then the steering shaft may require replacement.

5 vehicles · built 2 Apr 2011 to 3 Apr 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number. Depending on the identification number on the part then the steering shaft may require replacement.

5 vehicles · built 2 Apr 2011 to 3 Apr 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number. Depending on the identification number on the part then the steering shaft may require replacement.

5 vehicles · built 2 Apr 2011 to 3 Apr 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number. Depending on the identification number on the part then the steering shaft may require replacement.

5 vehicles · built 2 Apr 2011 to 3 Apr 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number and replace the shaft if necessary.

737 vehicles · built 12 Sep 2011 to 28 Mar 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number and replace the shaft if necessary.

737 vehicles · built 12 Sep 2011 to 28 Mar 2022

Some steering shafts were assembled with an incorrect component.

Fix: Inspect the steering shaft identification number and replace the shaft if necessary.

737 vehicles · built 12 Sep 2011 to 28 Mar 2022

Mandatory label may be missing at vehicle charging inlet

Fix: Install the decal in the front side of the charging plug on the vehicle

10 vehicles · built 24 Dec 2020 to 26 Aug 2021

Overheating of an internal component in the Electric Power Steering.

Fix: Recalibration of the Electronic Power Steering Calculator limiting the overheating at the end lock.

1,562 vehicles · built 11 Oct 2019 to 21 Nov 2021

Risk of internal short-circuit to the battery.

Fix: Controlling the battery and replacing the module if necessary.

31 vehicles · built 13 Jan 2021 to 22 Feb 2021

The rubber caps on the service brake air tanks EBS valves and trailer brake air tanks might be missing

Fix: Check rubber caps are assembled and if found to be missing fit caps as required

43 vehicles · built 4 Oct 2021 to 22 Oct 2021

The rubber caps on the service brake air tanks EBS valves and trailer brake air tanks might be missing

Fix: Check rubber caps are assembled and if found to be missing fit caps as required

43 vehicles · built 4 Oct 2021 to 22 Oct 2021

The rubber caps on the service brake air tanks EBS valves and trailer brake air tanks might be missing

Fix: Check rubber caps are assembled and if found to be missing fit caps as required

43 vehicles · built 4 Oct 2021 to 22 Oct 2021

Emissions control component could degrade earlier than expected

Fix: Replace the silencer module

7 vehicles · built 6 Dec 2013 to 27 May 2016

Emissions control component could degrade earlier than expected.

Fix: Replace the silencer module

187 vehicles · built 8 Jul 2013 to 16 Oct 2018

Emissions control component could degrade earlier than expected

Fix: Replace the silencer module

7 vehicles · built 6 Dec 2013 to 27 May 2016

Emissions control component could degrade earlier than expected.

Fix: Replace the silencer module

187 vehicles · built 8 Jul 2013 to 16 Oct 2018

Emissions control component could degrade earlier than expected.

Fix: Replace the silencer module

187 vehicles · built 8 Jul 2013 to 16 Oct 2018

Emissions control component could degrade earlier than expected

Fix: Replace the silencer

205 vehicles · built 4 Mar 2013 to 30 Apr 2019

Emissions control component could degrade earlier than expected

Fix: Replace the silencer module

7 vehicles · built 6 Dec 2013 to 27 May 2016

Emissions control component could degrade earlier than expected

Fix: Replace the silencer

205 vehicles · built 4 Mar 2013 to 30 Apr 2019

With an active EBS DTC EBS yellow tell-tale is displayed instead of EBS red tell-tale.

Fix: Update MID140 software

435 vehicles · built 1 Nov 2020 to 31 Jan 2021

Vehicles may be equipped and fitted with the incorrect rear right brake caliper.

Fix: Visual inspection of the rear right brake Caliper to check the ��date of manufacture�� code. Replace the caliper if affected.

167 vehicles · built 10 Feb 2021 to 26 Feb 2021

Vehicle may be equipped and fitted with the incorrect rear right brake Caliper.

Fix: Visual inspection of the rear right brake Caliper to check the ��date of manufacture�� code. Replace the caliper if affected.

176 vehicles · built 1 May 2021 to 1 Jul 2021

Error in emission control readings.

Fix: Carry out update to EMS and SW software.

1,044 vehicles · built 9 Sep 2013 to 4 Mar 2019

Error in emission control readings.

Fix: Carry out update to EMS and SW software.

1,044 vehicles · built 9 Sep 2013 to 4 Mar 2019

Fuel pipes chaffing might cause abnormal wear and consequently fuel leakages

Fix: Visual inspection adding protection on the fuel pipe replace pipe if applicable.

2,324 vehicles · built 1 Jan 2018 to 30 May 2019

Error in emission control readings.

Fix: Update Engine Management System (EWS) software.

3,667 vehicles · built 1 Feb 2013 to 1 Jun 2016

Error in emission control readings.

Fix: Update Engine Management System (EWS) software.

3,667 vehicles · built 1 Feb 2013 to 1 Jun 2016

Error in emission control readings.

Fix: Update Engine Management System (EWS) software.

3,667 vehicles · built 1 Feb 2013 to 1 Jun 2016

Error in emission control readings.

Fix: Update Engine Management System (EWS) software.

3,667 vehicles · built 1 Feb 2013 to 1 Jun 2016

Contact of the fuel supply hose with the cylinder head cover causing hose wear.

Fix: Carry out a visual inspection of the fuel supply hose and fit a protective sleeve. If necessary replace the fuel supply hose.

5,839 vehicles · built 2 Jan 2018 to 24 Apr 2019

Improved emission control and monitoring.

Fix: Update EMS and SW software.

5,178 vehicles · built 1 Jun 2016 to 1 May 2019

Improved emission control and monitoring.

Fix: Update EMS and SW software.

5,178 vehicles · built 1 Jun 2016 to 1 May 2019

Improved emission control and monitoring.

Fix: Update EMS and SW software.

5,178 vehicles · built 1 Jun 2016 to 1 May 2019

Improved emission control and monitoring.

Fix: Update EMS and SW software.

5,178 vehicles · built 1 Jun 2016 to 1 May 2019

Risk of a fuel leak in the engine compartment.

Fix: Inspect and install protection to the fuel pipe or replace the fuel pipe if damaged

293 vehicles · built 1 Feb 2018 to 2 Apr 2019

Nox emissions driver alert information.

Fix: Update EMS IC and ACM software.

1,286 vehicles · built 1 Jun 2016 to 1 Mar 2019

Nox emissions driver alert information.

Fix: Update EMS IC and ACM software.

1,286 vehicles · built 1 Jun 2016 to 1 Mar 2019

Nox emissions driver alert information.

Fix: Update EMS IC and ACM software.

1,286 vehicles · built 1 Jun 2016 to 1 Mar 2019

Risk of a fault in the trailer coupling socket due to incorrect positioning of the ground wire potentially causing the lights on the trailer to not function.

Fix: Cutting the existing ground wire and creating a mechanical splice for adding a ground wire using a specific realignment kit.

5 vehicles · built 27 Feb 2019 to 7 Nov 2019

Degradation of emissions control component.

Fix: Replacement of Silencer.

97 vehicles · built 1 Mar 2013 to 1 Aug 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

97 vehicles · built 1 Mar 2013 to 1 Aug 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

122 vehicles · built 1 Dec 2013 to 1 Sep 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

97 vehicles · built 1 Mar 2013 to 1 Aug 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

234 vehicles · built 1 Feb 2014 to 1 Feb 2019

Degradation of emissions control component.

Fix: Replacement of Silencer.

234 vehicles · built 1 Feb 2014 to 1 Feb 2019

Degradation of emissions control component.

Fix: Replacement of Silencer.

122 vehicles · built 1 Dec 2013 to 1 Sep 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

122 vehicles · built 1 Dec 2013 to 1 Sep 2018

Degradation of emissions control component.

Fix: Replacement of Silencer.

97 vehicles · built 1 Mar 2013 to 1 Aug 2018

Possible fuel leakage of the high pressure fuel pump system

Fix: Replace the high pressure pump and pipes

41 vehicles · built 1 Jul 2020 to 31 Jul 2020

Risk of the gas generator cracking on the passenger airbag causing a leak meaning the airbag may not display fully in an event of an accident.

Fix: Replace the passenger airbag as a preventive measure.

45 vehicles · built 29 Jan 2020 to 16 Mar 2020

The child lock disengages after it was activated by the customer.

Fix: Fit a retaining clip to the door locks.

45,023 vehicles · built 29 Jun 2015 to 2 Mar 2018

Lack of NOX-neutralizing substance in the catalytic converter meaning incorrect NOx Control

Fix: Replace the catalytic convertor

2 vehicles · built 25 Oct 2019 to 28 Oct 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

207 vehicles · built 1 Nov 2013 to 31 Oct 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

207 vehicles · built 1 Nov 2013 to 31 Oct 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

207 vehicles · built 1 Nov 2013 to 31 Oct 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

207 vehicles · built 1 Nov 2013 to 31 Oct 2016

There is a potential for the internal aggression in the fuel hose causing a fuel leak.

Fix: Replace the fuel supple pipe

197 vehicles · built 1 Sep 2018 to 31 May 2019

There is a potential for the internal aggression in the fuel hose causing a fuel leak.

Fix: Replace the fuel supple pipe

197 vehicles · built 1 Sep 2018 to 31 May 2019

Possible detachment of the fixed glass sunroof while driving.

Fix: Check the bonding and replace if required replace the fixed glass sunroof.

22 vehicles · built 21 Aug 2019 to 2 Sep 2019

Due to the incorrect calibration of the injection computer the fixed speed limiter is inoperative.

Fix: Re-program the injection computer.

134 vehicles · built 12 Sep 2019 to 8 Nov 2019

Crystallization in silencer and active MIL with engine derate.

Fix: Update EMS and ACM software.

130 vehicles · built 1 Mar 2019 to 1 Jan 2020

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

477 vehicles · built 1 Mar 2013 to 30 Apr 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

477 vehicles · built 1 Mar 2013 to 30 Apr 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

317 vehicles · built 1 Mar 2013 to 30 Jun 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

317 vehicles · built 1 Mar 2013 to 30 Jun 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

317 vehicles · built 1 Mar 2013 to 30 Jun 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

317 vehicles · built 1 Mar 2013 to 30 Jun 2016

There is a risk the handbrake may not hold the vehicle in place due to a non-conformity of the rear brake calipers

Fix: Check the manufacturing markings on the Left and Right Rear Brake Calipers and if necessary replace them

450 vehicles · built 28 Mar 2019 to 6 Jun 2019

The message power steering failure displayed on the vehicles dashboard and a down grading of the power steering assistance

Fix: The steering column will be replaced

72 vehicles · built 1 Jun 2019 to 31 Oct 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

88 vehicles · built 1 Mar 2013 to 31 Jan 2018

Inadequate tightening of the rear hub nuts and potentially of the calliper fixing screws on the left and right side

Fix: Check the torque of the fixing screws hub nuts and if required replace the screws bolts and the calliper.

50 vehicles · built 4 Sep 2019 to 11 Oct 2019

Contact between the positive alternator wiring and the alternator casing which could cause an electrical short circuit.

Fix: Modify the wiring route and if necessary replace the alternator

39 vehicles · built 8 Jul 2019 to 23 Jul 2019

Contact between the positive alternator wiring and the alternator casing which could cause an electrical short circuit.

Fix: Modify the wiring route and if necessary replace the alternator

39 vehicles · built 8 Jul 2019 to 23 Jul 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

33 vehicles · built 1 Apr 2013 to 30 Jun 2017

The left hand seatbelt fixing bolt may not have been set to the correct torque.

Fix: Check for the presence of the bolt and factory torque confirmation marking. If either are not present replace the bolt.

20 vehicles · built 13 Nov 2018 to 20 Dec 2018

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

68 vehicles · built 1 Nov 2013 to 31 Jan 2018

NOx sensor was not correctly tightened during manufacture on the production line

Fix: Tighten the NOx sensor to 32 Nm

116 vehicles · built 21 Sep 2018 to 3 Jun 2019

Crystallization in silencer and active MIL with engine derate.

Fix: Update EMS and ACM software.

197 vehicles · built 1 Mar 2019 to 1 Sep 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

53 vehicles · built 1 Jul 2013 to 31 Mar 2017

Premature degradation of emission control component

Fix: If found then replacement of Silencer

266 vehicles · built 1 Mar 2013 to 31 May 2017

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

53 vehicles · built 1 Jul 2013 to 31 Mar 2017

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

53 vehicles · built 1 Jul 2013 to 31 Mar 2017

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

53 vehicles · built 1 Jul 2013 to 31 Mar 2017

Premature degradation of emission control component

Fix: If found then replacement of Silencer

266 vehicles · built 1 Mar 2013 to 31 May 2017

Premature degradation of emission control component

Fix: If found then replacement of Silencer

3 vehicles · built 1 Dec 2014 to 30 Sep 2015

The oil pressure solenoid valve may not switch correctly.

Fix: Check the solenoid and modify or replace if required

272 vehicles · built 1 Mar 2018 to 31 May 2019

Premature degradation of emission control component.

Fix: If found then replacement of Silencer.

41 vehicles · built 1 Apr 2014 to 31 Mar 2016

Possible of deviation in the torque value on the U bolt for the rear right suspension blade

Fix: Check and adjust and if necessary replace the rear axle suspension U bolts.

5 vehicles · built 26 Mar 2018 to 2 Jun 2018

The STOP&START function does not perform correctly.

Fix: An update to the Power and Switching Unit software is required

570 vehicles · built 5 Dec 2018 to 19 Feb 2019

Possible insufficient clamping of the Right Rear suspension.

Fix: Retighten or replacement the right rear suspension clamps

14 vehicles · built 23 May 2018 to 4 Jul 2018

The oil pressure control solenoid valve may malfunction causing a blockage in the high oil pressure position when required for engine performance

Fix: Software update check and replacement of the oil pressure solenoid if required

240 vehicles · built 1 Sep 2018 to 5 Jul 2019

Possible Fuel leak from tank

Fix: Check the date of manufacture of the fuel tank and change it if necessary

3 vehicles · built 7 Mar 2019 to 14 Mar 2019

Rear bench seatbelt buckle bolts may not be correctly tightened.

Fix: Check the buckle bolts are at the correct torque.

7 vehicles · built 30 May 2017 to 30 Jan 2019

Possible failure of the parking brake due to a non-conformity (crimping) at cable connection ends.

Fix: Replace the secondary cables and connectors.

2,475 vehicles · built 18 May 2018 to 13 Sep 2018

Exhaust value solenoid wiring may short circuit due to contact on the exhaust.

Fix: Fit a protective sleeve to the wiring.

166 vehicles · built 1 Jul 2018 to 9 Nov 2018

Incorrect tightening of front luggage compartment (bonnet) bolts. Extreme risk front luggage compartment may open when driving.

Fix: Check and if required correct the torque of the front luggage compartment bolts.

206 vehicles · built 1 Jul 2018 to 27 Feb 2019

Emission monitoring software does not work as intended.

Fix: Update NOX MOMITOR software.

5,517 vehicles · built 1 Jun 2016 to 1 Mar 2019

Emission monitoring software does not work as intended.

Fix: Update NOX MOMITOR software.

5,517 vehicles · built 1 Jun 2016 to 1 Mar 2019

Emission monitoring software does not work as intended.

Fix: Update NOX MOMITOR software.

5,517 vehicles · built 1 Jun 2016 to 1 Mar 2019

Emission monitoring software does not work as intended.

Fix: Update NOX MOMITOR software.

5,517 vehicles · built 1 Jun 2016 to 1 Mar 2019

Emission monitoring software does not work as intended.

Fix: Update NOX MOMITOR software.

5,517 vehicles · built 1 Jun 2016 to 1 Mar 2019

The Auto brake adjuster may fail allowing the brake adjustment to wind off.

Fix: Replace the automatic brake adjuster housing on the calliper of each affected wheel.

119 vehicles · built 6 Aug 2018 to 18 Aug 2018

The Auto brake adjuster may fail allowing the brake adjustment to wind off.

Fix: Replace the automatic brake adjuster housing on the calliper of each affected wheel.

119 vehicles · built 6 Aug 2018 to 18 Aug 2018

The Auto brake adjuster may fail allowing the brake adjustment to wind off.

Fix: Replace the automatic brake adjuster housing on the calliper of each affected wheel.

119 vehicles · built 6 Aug 2018 to 18 Aug 2018

The Auto brake adjuster may fail allowing the brake adjustment to wind off.

Fix: Replace the automatic brake adjuster housing on the calliper of each affected wheel.

119 vehicles · built 6 Aug 2018 to 18 Aug 2018

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

13 vehicles · built 1 Sep 2014 to 30 Apr 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

13 vehicles · built 1 Sep 2014 to 30 Apr 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

13 vehicles · built 1 Sep 2014 to 30 Apr 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

13 vehicles · built 1 Sep 2014 to 30 Apr 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

5 vehicles · built 1 Oct 2016 to 31 Dec 2016

Premature degradation of emission control component.

Fix: If found then replacement of Silencer

5 vehicles · built 1 Oct 2016 to 31 Dec 2016

Capacitors for the engine cooling fan assembly do not comply with specification.

Fix: Replacement of the engine cooling fan assembly on affected vehicles.

163 vehicles · built 13 Sep 2018 to 15 Nov 2018

Rear seatbelt may become stuck due to incorrect fitting of the reel housing.

Fix: Check the fitting of the seat belt inertia reel housings and adjust as required.

5 vehicles · built 24 Jan 2018 to 24 Jan 2018

Incorrect positioning of the wiring causing a risk of the service indicator or vehicle stop warning light coming. The vehicle engine may no longer start or even shut down during use.

Fix: Check the battery wiring replacing it if necessary and in any case protecting it.

19 vehicles · built 1 Feb 2018 to 9 May 2018

Incorrect welding of the catalytic convertor.

Fix: Check the welding of the catalytic converter and replace it if necessary.

1 vehicles · built 20 Feb 2018 to 14 Apr 2018

Incorrect welding of the catalytic convertor.

Fix: Check the welding of the catalytic converter and replace it if necessary.

10 vehicles · built 20 Feb 2018 to 14 Apr 2018

Lighting fault after LED fitment

Fix: Re-programme and re-configure the Energy Manangement Module

152 vehicles · built 1 Jul 2016 to 1 Dec 2017

No warning light on the dashboard should the power steering fail

Fix: Re-programme dashboard computer

379 vehicles · built 1 Mar 2017 to 1 Nov 2017

The gearbox may not hold the vehicle in the park position when the vehicle is stationary (Position �P�). The vehicle may roll if the handbrake is not applied.

Fix: Recall the vehicles that are likely to be affected and replace the gearbox parking pin.

360 vehicles · built 9 Nov 2016 to 26 Apr 2017

Headlight (dipped beam) may not adjust correctly when switched on and therefore not light the road ahead sufficiently.

Fix: On affected vehicles make an adjustment of the headlight beam sensor.

19 vehicles

Headlight (dipped beam) may not adjust correctly when switched on and therefore not light the road ahead sufficiently.

Fix: On affected vehicles make an adjustment of the headlight beam sensor.

19 vehicles

The Steering column may become detached from the rack due to incorrectly tightened bolt.

Fix: On affected vehicles check for presence of retaining nut. If present tighten nut to specified torque. If nut is absent replace bolt and screw and tighten to specified torque. THE MANUFACTURER HAS ADVISED NOT TO DRIVE THE VEHICLE

124 vehicles · built 12 May 2016 to 26 Jun 2017

The front wheel hub may suffer cracking. Drivers may notice abnormal noise and in extreme cases the hub may fail.

Fix: On affected vehicles check manufacturing date of the wheel hubs and replace if required

23 vehicles · built 22 Sep 2017 to 25 Sep 2017

An incorrect accelerator pedal may be fitted which could cause discomfort or in extreme circumstances the pedal may get suck under the floor mat.

Fix: Recall the vehicles that are likely to be affected and check the accelerator pedal fitted. Replace the pedal where necessary.

218 vehicles · built 12 Jul 2017 to 18 Oct 2017

In the event of heavy breaking such as an emergency stop or an impact with heavy luggage in the boot the rear seats central hinge may break. There would be no prior warning to the customer. In extreme circumstances may cause the luggage to enter the passage compartment.

Fix: Recall the vehicles that are likely to be affected and fit a reinforcing bracket.

412 vehicles · built 9 May 2012 to 11 Jul 2017

Depending on driving style and road profile there is a risk of degradation of the front left sub axle carrier.

Fix: Recall the vehicles that are likely to be affected and checking the front left stub axle carrier casting number Where necessary replace the stub axle carrier.

187 vehicles

The strap of the diesel filter may brake causing the diesel filter to disconcert from its holder. Possibility of a noise in the engine compartment and in extreme cases fuel leakage.

Fix: Recall the vehicles that are likely to be affected and check the diesel filter strap. The filter strap will be replaced if necessary.

440 vehicles

The curtain airbag (one or both side) may not deploy in the event of a side impact because the pyrotechnic mix ratio in the ignitor could be incorrect..

Fix: Recall the vehicles that are likely to be affected and check the serial number of the curtain airbag. Replace airbag if required.

610 vehicles · built 20 Sep 2016 to 30 Nov 2016

The curtain airbag (one or both side) may not deploy in the event of a side impact because the pyrotechnic mix ratio in the ignitor could be incorrect..

Fix: Recall the vehicles that are likely to be affected and check the serial number of the curtain airbag. Replace airbag if required.

610 vehicles · built 20 Sep 2016 to 30 Nov 2016

The curtain airbag (one or both side) may not deploy in the event of a side impact because the pyrotechnic mix ratio in the ignitor could be incorrect..

Fix: Recall the vehicles that are likely to be affected and check the serial number of the curtain airbag. Replace airbag if required.

610 vehicles · built 20 Sep 2016 to 30 Nov 2016

If the vehicle is parked on a hill with park selected and the parking brake off or not fully applied the vehicle may not stay stationary. This results in a higher risk of collision.

Fix: Recall the vehicles that are likely to be affected and replace the parking brake mechanism and park wheel which are inside of the reducer.

561 vehicles · built 1 Jul 2015 to 31 Jan 2016

The outer part (skin) of the rear spoiler may detach from the vehicle and /or the pins on the glass tailgate. There would be no warning to the customer. However the possibility of detachment is increased due to the use of car washes.

Fix: Recall the vehicles that are likely to be affected and fit additional re-enforcement to the spoiler and bonnet.

5,623 vehicles · built 7 May 2014 to 10 Dec 2016

Operations 1) or 2) or operations 1) and 2) could be required: 1) The upper part of the bonnet (the bonnet skin) may detach from the rest of the bonnet due to poor adhesive being applied at the factory and deterioration over time. There would be no obvious signs to the customer. 2) The outer part (skin) of the rear spoiler may detach from the vehicle and /or the pins on the glass tailgate. There would be no warning to the customer.

Fix: Recall the vehicles that are likely to be affected and add re-enforcement to the spoiler and/or bonnet or both as required.

4,056 vehicles · built 7 May 2014 to 6 Jul 2015

The rear door child locks may deactivate when a door is slammed. There will be no warning that the child lock has gone from active to inactive.

Fix: Recall the vehicles that are likely to be affected and check the door child locks are to specification. If they are not they are to be replaced with ones that are to specification.

2,415 vehicles · built 20 May 2016 to 18 Jul 2016

In certain acceleration cases the automatic gearbox software does not engage the clutch fully and therefore the driver could experience a loss of drive and/or engine judder. The gearbox overheating warning light may also be displayed and there is a risk of loss of acceleration and or engine jerk.

Fix: Recall the vehicles that are likely to be affected and update the software for the automatic gearbox.

132 vehicles · built 1 Jun 2016 to 31 Jan 2017

The steering column housing may crack making the steering wheel adjustment not as expected and/or some control arms may become difficult to use them (indicators headlight control wipers).

Fix: Recall the vehicles that are likely to be affected and replace the upper steering column complete with housing and associated fixings.

7 vehicles · built 8 Nov 2016 to 9 Dec 2016

In sub-zero weather conditions the front windscreen blades arms may become frozen to the screen. In extreme circumstances when the wipers are activated the wiper arm linkage may weaken detach or bend. Should the linkage break or bend the wipers will not clear the screen effectively.

Fix: Recall the vehicles that are likely to be affected and replace the wiper linkage with a more robustly designed linkage.

68,552 vehicles · built 1 Nov 2012 to 31 Jul 2015

It has been identified that the side board hinges may fail. This could result in the detachment of the side board whilst the vehicle is in motion.

Fix: Recall all affected vehicles to install safety reinforcement brackets to the side raves of the body.

324 vehicles · built 1 Jan 2010 to 30 Apr 2015

It has been identified that the incorrect tyre pressure label has been fitted. In addition if orderer the spare wheel may also be incorrect. It is therefore possible that the stability of the vehicle could be affected.

Fix: Recall all affected vehicles to replace both the tyre pressure label and the spare wheel with new quality assured items.

32 vehicles · built 19 May 2015 to 25 Jan 2016

One of the rear axle bolts retaining the stub axle carrier on the left and/or right side may not have been correctly tightened.This could allow the stub axle to separate from it's mounting.

Fix: On affected vehicles check bolt tightness. If necessary or if bolt(s) is/are missing replace the axle assembly.

415 vehicles · built 1 Feb 2016 to 17 Feb 2016

The rear axle bolts may not have been correctly tightened which may generate a noise from inside the wheel arch or cause friction on the Tyre. If the concern is not addressed it is possible for the axle to become uncoupled from the body of the vehicle.

Fix: Recall the vehicles that are likely to be affected to ensure the bolts are at the correct torque. Where axle bolts are found to be missing the axle must be replaced.

18,486 vehicles · built 1 Mar 2014 to 21 Jan 2016

The customer may experience vibrations or noise from the steering wheel due to cracks starting in the steering wheel hub. If not rectified in the worst case over time the steering wheel could break and affect the directional control of the vehicle.

Fix: Recall the vehicles that are likely to be affected and check of the manufacturing date of the steering wheel hub. The steering wheel hub will be replaced it if the date is inside the identified period.

847 vehicles · built 10 Dec 2012 to 20 Jan 2013

The customer may experience vibrations or noise from the steering wheel due to cracks starting in the steering wheel hub. If not rectified in the worst case over time the steering wheel could break and affect the directional control of the vehicle.

Fix: Recall the vehicles that are likely to be affected and check of the manufacturing date of the steering wheel hub. The steering wheel hub will be replaced it if the date is inside the identified period.

847 vehicles · built 24 Sep 2012 to 4 Nov 2012

The customer may experience vibrations or noise from the steering wheel due to cracks starting in the steering wheel hub. If not rectified in the worst case over time the steering wheel could break and affect the directional control of the vehicle.

Fix: Recall the vehicles that are likely to be affected and check of the manufacturing date of the steering wheel hub. The steering wheel hub will be replaced it if the date is inside the identified period.

847 vehicles · built 12 Apr 2013 to 26 May 2013

The customer may experience vibrations or noise from the steering wheel due to cracks starting in the steering wheel hub. If not rectified in the worst case over time the steering wheel could break and affect the directional control of the vehicle.

Fix: Recall the vehicles that are likely to be affected and check of the manufacturing date of the steering wheel hub. The steering wheel hub will be replaced it if the date is inside the identified period.

847 vehicles · built 6 Nov 2013 to 15 Dec 2013

The bolts that hold the front seats to the floor may not be correctly tightened. This may cause the seat to become insecure and control of the vehicle to be compromised. Prior to failure there will be increased movement of the seat when getting in and out of the vehicle which should be noticeable to the driver.

Fix: Recall the vehicles that are likely to be affected to check and where necessary adjust the torque tightening of the rear bolts on the front seat runners.

217 vehicles

It has been identified that during production the EGR pipe has been manufactured from incorrect thickness material. Due to the affect of stresses i.e. heat vibration etc on the pipe it can lead to cracking. If there is significant crack there is a possibility exhaust gases could leak. This could cause surrounding parts to deteriorate. If this happens the vehicle will emit black smoke from the exhaust there will be a loss of power and a warning light will illuminate on the instrument panel.

Fix: Recall all affected vehicles and replace to the EGR pipe.

4,310 vehicles · built 9 Dec 2013 to 30 Sep 2015

It has been identified that the rear axle suspension spring hanger bracket bolt may not have been tightened to the correct specification. This can result in the bolt/nut loosing its torque which can result in the failure of the spring eye bolt. This could then affect the stability of the vehicle.

Fix: Recall all affected vehicles to check the rear axle suspension spring hanger/spring eye bolt and replace if required.

2,922 vehicles

The near side rear seat belt upper mounting bolt may not have been tightened to the correct specification. In the event of an accident the belt may be insecure and not act as intended.

Fix: On affected vehicles tighten bolt to correct specification

3 vehicles · built 23 Nov 2015 to 27 Nov 2015

On affected vehicles the turbocharger induction pipe may fail allowing oil to leak. Vehicle users may notice a drop in oil level which should also cause the oil warning lamp to illuminate. This may lead to engine failure and In extreme cases a risk of fire.

Fix: On affected vehicles replace the turbocharger oil induction pipe.

55 vehicles · built 9 Sep 2015 to 20 Sep 2015

There is a risk the passenger airbag mounting bolts are incorrectly installed which can lead to the airbag not correctly deploying. If a heavy front end collision occurs the passenger could sustain additional injury.

Fix: Recall the vehicles that are likely to be affected and check for the presence of the bolts and if missing fit new one(s).

348 vehicles · built 14 May 2014 to 1 Dec 2014

On affected vehicles the rear side members may not have been correctly constructed. This could compromise seat belt operation during a collision.

Fix: Renault Dealers will advise of any action required

64 vehicles

The beach seat base mounting screws may break when the bench is repeatedly repositioned to allow a flat load area. Should this happen a noise will be heard from the bench. In exceptional cases if the screw has broken this may cause a loss of protection during an impact.

Fix: Recall the vehicles that are likely to be affected and inspect the vehicle. A metal insert will be fitted between the seatback folding pivot and the mounting screw (left and right). Additionally the mounting screws (left and right) will also be replaced.

194 vehicles · built 1 Sep 2009 to 30 Sep 2014

The airbag computer (ECU) incorrectly interprets the data provided by the lateral shock sensors and can reverse it. In the event of a side impact that is severe enough to cause side air bag deployment there is a risk of either non-deployment or activation of the airbags on the opposite side to the impact

Fix: On affected vehicles re-programme of the airbag ECU

10,613 vehicles · built 1 Jul 2015 to 31 Mar 2016

On a small number of vehicles one or more of the bonnet lock bolts may not be correctly tightened. In exceptional cases this may cause the bonnet to open whilst driving.

Fix: On affected vehicles check and where necessary tighten bonnet lock bolts.

12,832 vehicles · built 1 Jan 2014 to 30 Mar 2016

The front wheel arch liners may have been incorrectly positioned which may cause them to rub against the front brake hoses. In rare circumstances this could cause a low leakage from both front flexible brake hose leading to gradual increased brake pedal travel in extreme cases a sudden bursting of the flexible hose with sudden increased brake travel and a resultant affect on the braking efficiency. A warning light indicating a low brake fluid level will be displayed on the dashboard.

Fix: Recall the vehicles that are likely to be affected and inspect the front wheel arch liners and brake hoses. Where necessary reposition the wheel arch liners and replace the brake hose/s.

999 vehicles

The wheel retaining nuts may not have been tightened top the correct specification during assembly.

Fix: Recall affected vehicles; Check and if necessary tighten wheel nuts to correct specification.

418 vehicles · built 1 Apr 2015 to 30 Nov 2015

The rear spoiler may detach at high speed due to high variance in temperature change. This is a result of a non-conformity with the production process.

Fix: Recall the vehicles that are likely to be affected for inspection and where necessary rebonding.

1,096 vehicles · built 1 Jan 2013 to 31 Dec 2015

On affected vehicles the drive to brake vacuum pump may fail. This may cause a loss of brake servo assistance and a hard brake pedal. It may also cause a reduction in engine power.

Fix: Check the manufacture date of the vacuum pump and where necessary replace the pump.

527 vehicles

On affected vehicles the drive to brake vacuum pump may fail. This may cause a loss of brake servo assistance and a hard brake pedal. It may also cause a reduction in engine power.

Fix: Check the manufacture date of the vacuum pump and where necessary replace the pump.

527 vehicles

On affected vehicles the drive to brake vacuum pump may fail. This may cause a loss of brake servo assistance and a hard brake pedal. It may also cause a reduction in engine power.

Fix: Check the manufacture date of the vacuum pump and where necessary replace the pump.

527 vehicles

On affected vehicles the drive to brake vacuum pump may fail. This may cause a loss of brake servo assistance and a hard brake pedal. It may also cause a reduction in engine power.

Fix: Check the manufacture date of the vacuum pump and where necessary replace the pump.

527 vehicles

On affected vehicles the drive to brake vacuum pump may fail. This may cause a loss of brake servo assistance and a hard brake pedal. It may also cause a reduction in engine power.

Fix: Check the manufacture date of the vacuum pump and where necessary replace the pump.

527 vehicles

Under excessive force to the belt the lock ring in the passenger seat belt retractor might break and the belt could become extendable. This will increase the risk of injury during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the passenger seat belt retractor and support.

223 vehicles · built 1 Jan 2010 to 30 Nov 2015

Under excessive force to the belt the lock ring in the passenger seat belt retractor might break and the belt could become extendable. This will increase the risk of injury during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the passenger seat belt retractor and support.

223 vehicles · built 1 Jan 2010 to 30 Nov 2015

Under excessive force to the belt the lock ring in the passenger seat belt retractor might break and the belt could become extendable. This will increase the risk of injury during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the passenger seat belt retractor and support.

223 vehicles · built 1 Jan 2010 to 30 Nov 2015

Under excessive force to the belt the lock ring in the passenger seat belt retractor might break and the belt could become extendable. This will increase the risk of injury during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the passenger seat belt retractor and support.

223 vehicles · built 1 Jan 2010 to 30 Nov 2015

Under excessive force to the belt the lock ring in the passenger seat belt retractor might break and the belt could become extendable. This will increase the risk of injury during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the passenger seat belt retractor and support.

223 vehicles · built 1 Jan 2014 to 30 Nov 2015

It is possible that the front wheel liners have been incorrectly positioned giving potential for them to rub against the front brake hoses. This in turn could in rare circumstances cause increased brake pedal travel and affect the braking efficiency of the vehicle. This issue may be highlighted by a warning message Braking system fault and a warning light on the dashboard.

Fix: Recall the vehicles that are likely to be affected and inspect the front wheel arch liners and brake hoses. If they are found to be incorrectly positioned they will be replaced free of charge.

49,748 vehicles · built 5 Mar 2013 to 2 Apr 2015

The front shock absorber (strut) mounting for the anti-roll bar rod may not be welded correctly. If the welding should fail there will initially be noise leading to the possibility for adversely affected vehicle handling because the anti-roll bar will no longer be connected the risk of contact and damage to the wheel rim tyre brake hose and ABS cable.

Fix: Recall the vehicles that are likely to be affected and check the shocker absorber (strut) build dates. The shock absorber that are in the affected range will be replaced.

1,022 vehicles · built 26 May 2014 to 30 Oct 2014

It is possible that the front wheel liners have been incorrectly positioned giving potential for them to rub against the front brake hoses. This in turn could in rare circumstances cause increased brake pedal travel and affect the braking efficiency of the vehicle. This issue may be highlighted by a warning message Braking system fault and a warning light on the dashboard.

Fix: Recall the vehicles that are likely to be affected and inspect the front wheel arch liners and brake hoses. If they are found to be incorrectly positioned they will be replaced free of charge.

31,320 vehicles · built 1 Jan 2013 to 31 Mar 2015

A fuel leak could occur at the fuel pressure sensor to injector rail seal due to a non conformance of production methods. If the leak occurs a smell will be noticed by the occupants of the vehicle.

Fix: Recall the vehicles that are likely to be affected and re-tighten the fuel pressure sensor to a specified higher torque value.

383 vehicles · built 1 Apr 2013 to 30 Apr 2014

Due to an error in the engine ECU software it is possible that the vehicle will suffer an unintended acceleration or not able to decelerate. The driver should still be able to control the vehicle by applying the brakes and manipulating the clutch and gears.

Fix: Recall all affected vehicles to reprogram the engine ECU with new software.

1,115 vehicles · built 13 Jun 2014 to 15 Dec 2014

Due to an error in the manufacturing process the seat belt buckle may not retain the belt during a frontal impact.

Fix: On affected vehicles check build date of seat belt assembly and replace if necessary.

393 vehicles · built 29 Sep 2014 to 29 Oct 2014

The parking brake cable may not have been assembled correctly which can result in either the inability to apply the parking brake or the inability to release the parking brake.

Fix: Recall the vehicles that are likely to be affected and replace the parking brake cable.

418 vehicles · built 6 Mar 2014 to 25 Nov 2014

The integrity of the front seat bench frame for the passengers may be compromised because of non-compliance during the manufacturing processes. Customer may hear noises coming from underneath the bench. They may also notice some cracking on the seat frame angles. If the seat fails during a collision the passengers have an elevated risk of injury.

Fix: Recall the vehicles that are likely to be affected and inspect the seat frame. Replace the seat where necessary.

1,425 vehicles · built 1 Sep 2014 to 31 Oct 2014

It is possible for the servo mounting bolts to loosen. If the noises are ignored over time it is possible for the brakes to be compromised.

Fix: Recall the vehicles that are likely to be affected and replace the brake pedal/servo mounting nuts.

622 vehicles · built 6 Mar 2014 to 25 Nov 2014

The front axle wishbone mounting nuts may not have been tightened to the correct specification. The driver may experience noise from the front axle or find the steering becomes vague.

Fix: Recall the vehicles that are likely to be affected to check the torque tightening of the axle wishbone nuts or replace if required.

936 vehicles · built 6 Mar 2014 to 25 Nov 2014

Seat belt tongue may not hold in the buckle sufficiently. In a collision the tongue may separate from the buckle putting the occupant of the affected belt at risk.

Fix: Recall the vehicles that are likely to be affected and replace the seatbelt buckle on the passenger side (x 75) and driver side (x6).

393 vehicles · built 20 Oct 2014 to 7 Nov 2014

It has been identified that the steering wheel securing bolt may work loose. This can ultimately result in the securing bolt unscrewing and the steering wheel detaching. This would then result in loss of directional control. However the concern should be identified to the driver by the movement in the wheel before it becomes an issue.

Fix: Recall all affected vehicles to check and replace the steering wheel securing bolt.

1,647 vehicles

It has been identified that the steering wheel securing bolt may work loose. This can ultimately result in the securing bolt unscrewing and the steering wheel detaching. This would then result in loss of directional control. However the concern should be identified to the driver by the movement in the wheel before it becomes an issue.

Fix: Recall all affected vehicles to check and replace the steering wheel securing bolt.

1,647 vehicles

It has been identified that the steering wheel securing bolt may work loose. This can ultimately result in the securing bolt unscrewing and the steering wheel detaching. This would then result in loss of directional control. However the concern should be identified to the driver by the movement in the wheel before it becomes an issue.

Fix: Recall all affected vehicles to check and replace the steering wheel securing bolt.

1,647 vehicles

It has been identified that the steering wheel securing bolt may work loose. This can ultimately result in the securing bolt unscrewing and the steering wheel detaching. This would then result in loss of directional control. However the concern should be identified to the driver by the movement in the wheel before it becomes an issue.

Fix: Recall all affected vehicles to check and replace the steering wheel securing bolt.

1,647 vehicles

Brake pipes fitted to the ABS unit may not have been fitted to the correct port. During heavy braking conditions this may cause under braking. It is also possible that the ESP may malfunction/fail to work which may cause under/over steer.

Fix: Affected vehicles will be recalled to check brake pipes are fitted correctly to the ABS unit. Where necessary the brake pipes will be replaced.

772 vehicles · built 1 Oct 2012 to 14 May 2013

The protectors for the front brake hoses may have been fitted incorrectly which could in the worst case scenario lead to a reduction in braking efficiency. If there is leakage of brake fluid the warning lamp will illuminate and more effort will have to be applied to the brakes to stop in good time. Additionally there is a possibility that brake fluid may leak from the rear brake cylinders with the same effects as above.

Fix: Recall the vehicles that are likely to be affected to check the front brake hoses and protectors. Where necessary reposition or replace the protectors and brake hoses. Replace the fixing dome caps that retain the rear brake shoes to the back plate.

20,545 vehicles · built 22 Nov 2012 to 24 Jul 2014

There is a possibility that the rear lights may cease to function due to the wiring insulation being abraded on a roof lining angle bracket. If the rear lights cease to function there is an increased risk of collision as other road users are not warned of vehicle; position directional intent or braking intent. Warnings for the driver can be gained from acrid smell indicator tell-tale flashing faster than normal and other electrical items in the rear not working.

Fix: Recall the vehicles that are likely to be affected to check and where necessary replace the wiring. In all cases protection for the wiring will be fitted.

648 vehicles · built 20 Jul 2011 to 11 Sep 2013

It is possible that the rear body shelf fixing may not be secured to the vehicle sufficiently. This may lead to the detachment of the shelf and place other road users at risk.

Fix: Recall all affected vehicles and fit additional fixings.

3,842 vehicles · built 31 May 2010 to 14 Oct 2013

The prop shaft to axle flange bolts may not be tightened to the correct torque. The condition could develop noise and vibration and if not corrected loss of drive.

Fix: Recall the vehicles that are likely to be affected to either re torque the prop shaft to axle flange mounting bolts or where necessary replace the nuts and bolts and apply the correct torque.

1,145 vehicles · built 7 Apr 2010 to 14 Oct 2013

It has been identified that due to a quality issue the T Valve within the brake systems may develop a leak. The compressor should be able to keep up with this leak and the driver should be made aware of the issue. However the brake system pressure will be reduced which will potently affect the brake efficiency of the vehicle.

Fix: Replace all affected vehicles and check the valve numbers. If found to be within the affected batch replace with a new quality assured valve.

64 vehicles · built 1 Feb 2014 to 31 Mar 2014

The prop shaft to axle flange bolts may not be tightened to the correct torque. The condition could develop noise and vibration and if not corrected loss of drive.

Fix: Recall the vehicles that are likely to be affected to either re torque the prop shaft to axle flange mounting bolts or where necessary replace the nuts and bolts and apply the correct torque.

103 vehicles

The fuel pipe protective cover may fail and damage the engine. In the worst case the engine could cease to function.

Fix: Recall the vehicles that are likely to be affected to replace the fuel pipe protective cover with a modified type.

2,496 vehicles

As a result of certain front suspension mounting bolts being over tightened at the factory the front suspension could fail and loss of vehicle control could occur.

Fix: Recall the vehicles that are likely to be affected to replace the front struts and mounting bolts.

3 vehicles

The rear spoiler may detach at high speed due to high variance in temperature change aggressive car wash systems or use of racks as they may weaken the spoiler mouldings.

Fix: Recall the vehicles that are likely to be affected for rebonding or reinforcement of the rear tailgate spoiler (depending on type of tailgate).

22,739 vehicles · built 1 Sep 2003 to 31 Oct 2009

Possibility that brake fluid may leak from the rear brake calipers. This could result in a loss of braking efficiency

Fix: Replace rear brake calipers if required.

225 vehicles · built 27 Jan 2012 to 1 May 2012

The injection computer requires reprogramming. If this is not carried out reduced braking assistance may be noticed

Fix: Preventive operation: 1. Reprogramme the injection computer; 2. Reconfigure the UPC computer.

31 vehicles

The injection computer requires reprogramming. If this is not carried out reduced braking assistance may be noticed

Fix: Preventive operation: 1. Reprogramme the injection computer; 2. Reconfigure the UPC computer.

31 vehicles

There is a possible issue with the security of the lower seat belt mounting bolt which could cause it to loosen. If this were to occur then the bolt could ultimately fully unwind and detach. This could result in the occupant not being restrained by the seat belt in the event of a collision.

Fix: Recall all affected vehicles and replace the lower seat belt mounting bolts.

2,243 vehicles

Possibility that the nonconformance of the valve cotter could lead to the destruction of the engine.

Fix: Replace the cotters on relevant engines

3,308 vehicles · built 17 Sep 2010 to 30 Nov 2010

It is possible that the rear wheel bearing has been damaged whilst it was assembled onto the stub axle. This should be identified by excessive noise however in the worst case if not detected it could result in bearing failure and the detachment of the wheel and hub.

Fix: Recall all the affected vehicles and replace the wheel bearings with new items which will have protective sleeves to aid correct installation.

218 vehicles · built 1 Apr 2010 to 16 Apr 2010

It is possible that the rear wheel bearing was damaged whilst it was assembled onto the stub axle. This could result in bearing failure and the detachment of the wheel and hub.

Fix: Replace rear wheel bearing and hub carrier.

13 vehicles

It is possible that the rear wheel bearing was damaged whilst it was assembled onto the stub axle. This could result in bearing failure and the detachment of the wheel and hub.

Fix: Replace rear wheel bearing and hub carrier.

2 vehicles

The spare wheel carrier winch system may allow the spare wheel to be loosely installed after the customer has used the winch. In this condition the spare wheel might move during driving which may damage and eventually break the cable and guiding pin of the winch system. In this worst case the spare wheel would become detached from the vehicle.

Fix: Recall the vehicles that are likely to be affected to replace the complete spare wheel winch system.

1,318 vehicles · built 1 Apr 2010 to 29 Aug 2010

The spare wheel carrier winch system may allow the spare wheel to be loosely installed after the customer has used the winch. In this condition the spare wheel might move during driving which may damage and eventually break the cable and guiding pin of the winch system. In this worst case the spare wheel would become detached from the vehicle.

Fix: Recall the vehicles that are likely to be affected to replace the complete spare wheel winch system.

107 vehicles

Risk of contact between the power - assisted steering electrical supply and the steering column universal joint which could lead to power-assistance failure.

Fix: Repositioning of the electrical cable away from steering universal joint.

3 vehicles · built 1 Oct 2009 to 12 Mar 2010

The drivers airbag may not deploy in an accident and the passenger airbag could deploy at anytime even when it has been deactivated.

Fix: Recall the vehicles that are likely to be affected to reprogramme the airbag computer.

337 vehicles · built 1 Jun 2010 to 23 Aug 2010

Risk of losing steering due to the incorrect tightness of the universal joint fixing screw.

Fix: Retighten screw if required to the correct torque and paint mark on screw and the clamp

10 vehicles

Risk of losing steering due to the incorrect tightness of the universal joint fixing screw.

Fix: Retighten screw if required to the correct torque and paint mark on screw and the clamp

10 vehicles

Risk of losing steering due to the incorrect tightness of the universal joint fixing screw.

Fix: Retighten screw if required to the correct torque and paint mark on screw and the clamp

10 vehicles

Cracked R/H/F hub carrier. This has the potential risk of the hub carrier rupturing.

Fix: Replacement of the hub carrier.

61 vehicles · built 14 Apr 2004 to 5 May 2004

Risk that the primary handbrake cable end - piece crimping may not conform so the handbrake cable may become detached.

Fix: Check crimping at cable end. Replace cable if not within tolerance.

1,180 vehicles

It is possible that the rear axle wheel bearing securing nut may not be correctly crimped. This could result in the slackening of the torque on the bearing and possible in extreme conditions detachment of the hub assembly. Warning of the issue is provided to the driver in the form of either a vibration or the illumination of the ABS warning light.

Fix: Recall all affected vehicles to check and if required replace the bearing securing nut.

6 vehicles

It is possible that the rear axle wheel bearing securing nut may not be correctly crimped. This could result in the slackening of the torque on the bearing and possible in extreme conditions detachment of the hub assembly. Warning of the issue is provided to the driver in the form of either a vibration or the illumination of the ABS warning light.

Fix: Recall all affected vehicles to check and if required replace the bearing securing nut.

6 vehicles

Because of a manufacturing error the nearside rear stub axle could start to develop cracks at the inner radius which could eventually lead to failure of the stub axle and difficulty in maintaining directional control.

Fix: Recall the vehicles that are likely to be affected to replace the rear axle.

14 vehicles

There is a risk that the nearside rear axle spindle may crack which in the most serious cases will lead to the spindle breaking which dependent on loading could make directional control difficult to maintain.

Fix: Recall the vehicles that are likely to be affected to change the rear axle.

228 vehicles · built 1 Apr 2010 to 16 Apr 2010

It has been found that some of the front seat mounting brackets have not been correctly fitted to the seats. The front seat mountings could fail if the fitting brackets have been incorrectly fitted. Vehicle control could be affected.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit new seat assemblies.

965 vehicles · built 1 Apr 2010 to 9 Jul 2010

The seat belt positioning may be incorrect due to the front seat brackets not being to specification. This could affect the seat security and seat belt performance if an accident occurs.

Fix: Recall the vehicles that are likely to be affected to check and where necessary fit new seat assemblies.

67 vehicles

Engine oil may leak due to the turbocharger oil pipe not being to specification. If not corrected this concern could lead to a skid danger to other road users catastrophic failure of the turbo/engine or in the worst case fire.

Fix: Recall the vehicles that are likely to be affected to replace the turbocharger oil l pipe.

77 vehicles

The suspension turret panel may fail due to inadequate welding being applied at the factory.

Fix: Recall the vehicles that are likely to be affected to apply further weld to the nearside inner wing suspension turret.

22 vehicles · built 26 Jul 2006 to 29 Jul 2006

It has been identified that the possibility exists that the front brakes hoses may become disconnected resulting in a loss of brake hydraulic fluid and a reduction in braking efficiency.

Fix: Recalled vehicles will have both front brake hoses replaced.

149 vehicles · built 1 Apr 2009 to 24 Apr 2009

The parking brake may apply without input from the driver as a result of a programming error.

Fix: Recall the vehicles that are likely to be affected to check and where necessary reprogramme the electronic parking brake computer.

66,735 vehicles · built 1 Sep 2003 to 30 Jun 2005

There is a possibility that the drivers seat belt pretensioner cable may fail through fatigue and therefore not restrain the driver correctly during a collision.

Fix: Recall the vehicles that are likely to be affected to replace the pretensioner with one that is redesigned.

9,959 vehicles · built 1 Jan 2007 to 24 Aug 2009

The rear passengers may not be sufficiently restrained during an accident if the manually adjustable bench seat mechanism jams.

Fix: Recall the vehicles that are likely to be affected to fit a reinforcement bracket and a cable tie to the seat adjustment mechanism.

4,403 vehicles · built 1 Jan 2008 to 26 Oct 2009

Due to the non-conformity of some welds under situations of extreme braking the driver's seat may detach from the floor fixing.

Fix: Recalled vehicles will have the subject welds and fixing lugs re-welded.

4,591 vehicles · built 22 Jan 2008 to 18 May 2009

Due to the non-conformity of some welds under situations of extreme braking the driver's seat may detach from the floor fixing.

Fix: Recalled vehicles will have the subject welds and fixing lugs re-welded.

942 vehicles

The rear pneumatic suspension leaves may fail this will result in noise from the suspension and if not rectified may result in loss of directional control.

Fix: Recall the affected vehicles for the replacement of the rear pneumatic suspension leaves.

1,947 vehicles

The rear pneumatic suspension leaves may fail this will result in noise from the suspension and if not rectified may result in loss of directional control.

Fix: Recall the affected vehicles for the replacement of the rear pneumatic suspension leaves.

1,947 vehicles

It has been identified that the possibility exists that the air suspension leaves of the rear axle may fail. This in the worst case can lead to loss of directional control.

Fix: Recalled vehicles will have the rear axle air suspension leaves replaced.

17 vehicles

It has been identified that the possibility exists that the air suspension leaves of the rear axle may fail. This in the worst case can lead to loss of directional control.

Fix: Recalled vehicles will have the rear axle air suspension leaves replaced.

17 vehicles

It has been identified that the securing bolts for the steering column connecting rod may not have been tightened to the correct torque. This can in the worst case result in loss of steering control.

Fix: Recalled vehicles will have the subject bolts tightened to the correct torque.

124 vehicles

It has been identified that the mounting bolts of the turbo hose mounting flanges may not have been tightened to the correct torque. In this condition oil may leak with the attendant risk of fire.

Fix: Recalled vehicles will have the subject bolts tightened to the correct torque.

89 vehicles

Tyres of an incorrect size have been fitted which could result in tyre failure.

Fix: Recall the affected vehicles to replace the five tyres the spare wheel carrier mountings and reconfigure the ABS computer.

48 vehicles · built 1 Mar 2006 to 31 Mar 2007

It has been identified that the mounting bolts of the turbo hose mounting flanges may not have been tightened to the correct torque. In this condition oil may leak with the attendant risk of fire.

Fix: Recalled vehicles will have the subject bolts tightened to the correct torque.

89 vehicles

The steering column mounting nut on the steering rack may become loose which may lead to the column coming out of position and loss of steering control.

Fix: Recall affected vehicles to fit a retaining flange for the column mounting nut.

2,774 vehicles

Power assistance to the steering might be lost because of a problem in the software.

Fix: Recall the vehicles that are likely to be affected to reprogramme the ECU.

34,403 vehicles

Power assistance to the steering might be lost because of a problem in the software.

Fix: Recall the vehicles that are likely to be affected to reprogramme the ECU.

34,403 vehicles · built 1 Jan 2006 to 31 Mar 2007

The rear outboard seat belt stalks may become less effective as it is possible for the mounting bolt to unscrew.

Fix: Recall the vehicles that are likely to be affected to apply thread locking compound to the appropriate seat belt stalk fixings.

1,429 vehicles

It has been identified that the driver's seat may suffer permanent or intermittent non-locking on it's runners. This can occur when the vehicle is stationary or when being driven..

Fix: Recalled vehicles will have a latch fitted to the seat's locking device.

663 vehicles · built 1 Sep 2008 to 28 Feb 2009

It has been identified that the near and offside locking plunger fixing bolts may have been incorrectly located. Should this be the case the fifth wheel would not be correctly locked to the slider frame.

Fix: Recalled vehicles will have the subject bolts checked for correct fitment with the fifth wheel being changed if this is not the case.

160 vehicles · built 2 Apr 2008 to 29 May 2008

It has been identified that the near and offside locking plunger fixing bolts may have been incorrectly located. Should this be the case the fifth wheel would not be correctly locked to the slider frame.

Fix: Recalled vehicles will have the subject bolts checked for correct fitment with the fifth wheel being changed if this is not the case.

160 vehicles · built 2 Apr 2008 to 29 May 2008

It has been identified that the possibility exists that the handbrake cable intermediate connector may break. Should this occur the handbrake function would be lost.

Fix: Recalled vehicles will have the handbrake intermediate connector replaced.

26,355 vehicles · built 1 Jan 2006 to 29 May 2008

It has been identified that the possibility exists that the handbrake cable intermediate connector may break. Should this occur the handbrake function would be lost.

Fix: Recalled vehicles will have the handbrake intermediate connector replaced.

26,355 vehicles · built 10 Jun 2008 to 10 Jun 2008

It has been identified that there has been a left to right inversion of the side impact sensor wiring which in certain cases may result in inadequate deployment of the airbags in the event of a side impact.

Fix: Recalled vehicles will have the airbag ECU replaced.

84 vehicles

There is a possibility that the semi trailer may uncouple due to the locking pin in the fifth wheel's control handle being insufficient.

Fix: Recall the vehicles that are likely to be affected to check the serial number of the fifth wheel and where necessary fit a locking pin kit.

5 vehicles

There is a possibility that the semi trailer may uncouple due to the locking pin in the fifth wheel's control handle being insufficient.

Fix: Recall the vehicles that are likely to be affected to check the serial number of the fifth wheel and where necessary fit a locking pin kit.

5 vehicles

There is a possibility that the semi trailer may uncouple due to the locking pin in the fifth wheel's control handle being insufficient.

Fix: Recall the vehicles that are likely to be affected to check the serial number of the fifth wheel and where necessary fit a locking pin kit.

5 vehicles

There is a possibility that there are no Isofix mounting rings at the rear. It is therefore not possible to secure an Isofix child seat in the rear seats nor the luggage net in the boot.

Fix: Recall affected vehicles and fit two mounting rings.

545 vehicles · built 1 Mar 2007 to 2 Sep 2007

It has been identified that there exixts a sustatial risk of leakage from the engine oil filter housing.

Fix: Recalled vehicles will have the functionality of the oil sprayer ramp and supply valve checked and if necessary replace filter housing.

57 vehicles · built 11 May 2007 to 22 Oct 2007

It has been identified that there exixts a sustatial risk of leakage from the engine oil filter housing.

Fix: Recalled vehicles will have the functionality of the oil sprayer ramp and supply valve checked and if necessary replace filter housing.

57 vehicles · built 11 May 2007 to 22 Oct 2007

It has been identified that the possibility exists that the front seat head restraint components may have been incorrectly welded into position in the seat frame. This in certain cases can cause the sleeve to become loose to the seat frame. This has the potential to prevent the front seat head restraints retaining their position in the event of an impact.

Fix: Recalled vehicles will have the fabrication of the two front seat back frames checked. These will be replaced if found to be necessary.

76 vehicles · built 27 Oct 2004 to 28 Oct 2004

It has been identified that the dashboard wiring hs been mounted incorrectly. This may result in the vehicle failing to start the reversing lights failing to operate the risk of a short circuit of the FRH headlights damage to the wiring and high temperatures.

Fix: Recalled vehicles will have the dashboard wiring refitted and replaced as necessary.

2 vehicles · built 1 May 2006 to 10 Apr 2007

It has been identified that the dashboard wiring hs been mounted incorrectly. This may result in the vehicle failing to start the reversing lights failing to operate the risk of a short circuit of the FRH headlights damage to the wiring and high temperatures.

Fix: Recalled vehicles will have the dashboard wiring refitted and replaced as necessary.

2 vehicles · built 1 May 2006 to 8 Mar 2007

It has been identified that the front brake chambers of affected vehicles may have been incorrectly torqued. Should this be the case detachment of the chamber and subsequent loss of braking effort at the affected wheel station may occur.

Fix: Recalled vehicles will have the front brake chambers checked for conformity. The chambers will be replaced should any nonconformance be found.

22 vehicles · built 3 Sep 2007 to 17 Sep 2007

It has been identified that there is a risk of contact between the starter motor cable and the exhaust heat shielding. Should this occur and the cable insulation become damaged an electrical short circuit with the attendant risk of fire might ensue.

Fix: Affected vehicles will have the exhaust heat shielding re-shaped to prevent contact with the starter cable.

4 vehicles · built 9 Sep 2007 to 24 Sep 2007

It has been identified that there is a risk of contact between the starter motor cable and the exhaust heat shielding. Should this occur and the cable insulation become damaged an electrical short circuit with the attendant risk of fire might ensue.

Fix: Affected vehicles will have the exhaust heat shielding re-shaped to prevent contact with the starter cable.

4 vehicles · built 9 Sep 2007 to 24 Sep 2007

It has been identified that the front passenger seatbelt pretensioner has not been configured correctly. In the event of an impact the pretensioner will not trigger. The front seat passenger will however still be retained by the seatbelt but without the pretensioner function.

Fix: Recalled vehicles will have the front passenger seatbelt configured.

6 vehicles

The rear ABS sensor mountings may come loose which may lead to the rear ABS not working.

Fix: Recall the vehicles that are likely to be affected to tighten the ABS sensor mounting fixing screws.

3 vehicles · built 23 May 2006 to 22 Jun 2007

It has been identified that a potential loss of engine cooling fan function (cooling fan number 2) will cause the engine to seize without warning due to overheating. The STOP warning light may or may not illuminate.

Fix: Recalled vehicles will have front-end wiring replaced.

12 vehicles

Under particular circumstances of use the potential exists for the stop light switch to melt due to overheating of the grease in the circuit switches with the potential for coking of the contacts. This can result in failure of the stop lights and overheating at the pedal floor or smoke in the passenger compartment.

Fix: Recalled vehicles will have the stop light switch replaced.

4,234 vehicles · built 14 Dec 2005 to 16 Feb 2006

Under particular circumstances of use the potential exists for the stop light switch to melt due to overheating of the grease in the circuit switches with the potential for coking of the contacts. This can result in failure of the stop lights and overheating at the pedal floor or smoke in the passenger compartment.

Fix: Recalled vehicles will have the stop light switch replaced.

4,234 vehicles · built 13 Dec 2005 to 8 Feb 2006

It has been identified that during production the fifth wheel sub-frame mounting bolts were not tightened to the correct torque.

Fix: Recalled vehicles will have the subject bolts checked for the correct torque.

4 vehicles · built 30 May 2006 to 5 Feb 2007

Water may be present in the rear brake actuators which in certain circumstances can cause the rear brakes to lock up when driving.

Fix: Recall the vehicles that are likely to be affected to drain any water from the rear brake actuators.

364 vehicles · built 1 Jun 2006 to 8 Feb 2007

Water may be present in the rear brake actuators which in certain circumstances can cause the rear brakes to lock up when driving.

Fix: Recall the vehicles that are likely to be affected to drain any water from the rear brake actuators.

364 vehicles · built 1 Jun 2006 to 8 Feb 2007

Water may be present in the rear brake actuators which in certain circumstances can cause the rear brakes to lock up when driving.

Fix: Recall the vehicles that are likely to be affected to drain any water from the rear brake actuators.

364 vehicles · built 1 Jun 2006 to 8 Feb 2007

It has been identified that the potential exists for the generation of an oil leak caused by the turbo oil supply pipe becoming loose. Should an oil leak from this component occur the possibility exists that a fire could ensue.

Fix: Recalled vehicles will have the turbo oil supply pipe checked and replaced as necessary.

270 vehicles · built 1 Jan 1987 to 31 May 1993

There is a possibility that the seat back of the front seats may become difficult to adjust and or not lock into position.

Fix: Recall the vehicles that are likely to be affected to check that all welding to the seat back frame is present. If the welds are not all present then the seat back frame will be replaced.

5,354 vehicles · built 1 Aug 2003 to 31 Oct 2003

There is a possibility that the seat back of the front seats may become difficult to adjust and or not lock into position.

Fix: Recall the vehicles that are likely to be affected to check that all welding to the seat back frame is present. If the welds are not all present then the seat back frame will be replaced.

5,354 vehicles · built 1 Sep 2003 to 31 Oct 2003

Possible malfunction of the gearbox control causing: 1. Gearbox switching to manual mode without driver intervention; 2. gearbox changing to 3rd gear without driver intervention; 3.incorrect display of lever position on the instrument panel; 4. Auto gearbox warning light illuminates.

Fix: Recall the vehicles that are likely to be affected to replace the automatic transmission computer.

217 vehicles · built 10 Nov 2005 to 29 May 2006

There is a possibility that the seat back of the front seats may become difficult to adjust and or not lock into position.

Fix: Recall the vehicles that are likely to be affected to check that all welding to the seat back frame is present. If the welds are not all present then the seat back frame will be replaced.

173 vehicles · built 1 Sep 2003 to 30 Sep 2003

Possible malfunction of the gearbox control causing: 1. Gearbox switching to manual mode without driver intervention; 2. gearbox changing to 3rd gear without driver intervention; 3.incorrect display of lever position on the instrument panel; 4. Auto gearbox warning light illuminates.

Fix: Recall the vehicles that are likely to be affected to replace the automatic transmission computer.

217 vehicles · built 7 Mar 2006 to 29 May 2006

The tie rod may separate from the ball joint which could result in loss of directional control.

Fix: Recall the vehicles that are likely to be affected and fit new tie rods.

330 vehicles · built 1 Dec 2004 to 31 Mar 2005

The tie rod may separate from the ball joint which could result in loss of directional control.

Fix: Recall the vehicles that are likely to be affected and fit new tie rods.

330 vehicles · built 1 Dec 2004 to 31 Mar 2005

It is possible that the rear caliper handbrake lever to crack and weaken. In the worst case there is a possibility that the parking brake cables will release.

Fix: Recall the vehicles that are likely to be affected and check the caliper handbrake lever for evidence of a crack. Where a crack exists on the lever the caliper will be replaced.

1,023 vehicles · built 24 Oct 2005 to 17 Jan 2006

It has been identified that the risk of a short circuit exists between individual wires of the engine wiring loom.

Fix: Recalled vehicles will have the engine wiring loom checked for condition and wear and will proceed as follows. If no wiring cores are visible a protective sheath will be fitted to the wiring loom. If the core of one or more of the wires is visible the wiring loom will be replaced.

1,100 vehicles

It has been identified that the possibility exists that the stop for the foot brake pedal collapse system is missing. This can result in the loss of braking efficiency when the brake pedal is at full travel.

Fix: Recalled vehicles will be inspected for the presence of the brake pedal collapse system stop and where this is found to be missing the brake pedal will be replaced.

57,995 vehicles · built 1 Sep 2002 to 12 Feb 2004

It has been identified that the possibility exists that the stop for the foot brake pedal collapse system is missing. This can result in the loss of braking efficiency when the brake pedal is at full travel.

Fix: Recalled vehicles will be inspected for the presence of the brake pedal collapse system stop and where this is found to be missing the brake pedal will be replaced.

57,995 vehicles · built 1 Sep 2003 to 21 Jan 2004

It is possible under certain conditions for the seatbelt stalk fixings on the first row of rear seats to become loose.

Fix: Recall the vehicles that are likely to be affected to remove the bolts retaining the stalks of the affected seatbelts. Thread adhesive is to be applied to the bolts then the bolts are to be refitted and torqued.

93,289 vehicles · built 1 Feb 2003 to 12 Dec 2005

The parking brake control levers on the rear calipers may not be to specification

Fix: Recall the vehicles that are likely to be affected to check the parking brake control levers on the rear calipers. Where the levers are not to specification replace the calipers.

105 vehicles · built 23 Oct 2005 to 26 Jan 2006

It has been identified that due to a heat treatment problem premature wear of the steering linkage ball joints may take place.

Fix: Recalled vehicles will have the subject components replaced with quality certified parts.

497 vehicles

Due to the possible non-conformity of the gearbox control there is a risk that the transmission may disengage from the parking position (without the footbrake having first been applied)

Fix: Recalled vehicles will have the conformity of the gearbox control checked and replaced as necessary.

55 vehicles · built 10 Nov 2004 to 25 Nov 2004

The possibility exists that due to an electrical overload within the ECU of the night heater there is a risk of a fire within the cab.

Fix: Recalled vehicles will have a supplementary fused wiring harness fitted.

505 vehicles · built 1 Jun 2002 to 15 Jul 2005

Due to a manufacturing error an excess of paint has been applied to the wheel mounting faces. In consequence the possibility exists that there may be a loss of wheel fixing torque.

Fix: Recalled vehicles will have any excess paint removed from the mating and locating surfaces of the wheels.

101 vehicles · built 16 Aug 2005 to 13 Oct 2005

It is possible that the steering wheel may become loose on the steering column mounting splines which could eventually damage the splines.

Fix: Recall affected vehicles replace the steering wheel and mounting bolt with quality assured items.

19 vehicles · built 14 Apr 2004 to 28 May 2004

It has been identified on a pre series vehicle that the fuel pre-heater may over heat with the result that a fire might ensue.

Fix: Recalled vehicles will have the pre-heater circuit connected and a heat insulator fitted.

65 vehicles · built 23 Feb 2005 to 28 Sep 2005

There is a possiblility that a voltage surge may overload the independent cab heater electronic control which could damage the circuit card which could lead to a fire.

Fix: Recall the affected vehicles and replace the fuse with one of a lower rating.

55 vehicles · built 23 Feb 2005 to 28 Sep 2005

A risk exists that the steering column intermediate shaft has been incorrectly fitted.

Fix: Recalled vehicles will have the position of the mounting yolk of the intermediate shaft checked and modified as necessary.

9,514 vehicles · built 1 Aug 2004 to 5 Apr 2005

Potential of an odour and smoke emission from the dashboard

Fix: Affected vehicles will have a resistor removed from the wiring circuit

398 vehicles · built 15 Nov 2003 to 2 Apr 2004

In certain cases the risk exists that there may be a faulty contact between the accelerator pedal sensor and the injection computer. In such cases the SERV warning light will illuminate on the dashboard.The situation remains under control by simply by applying the brake pedal.

Fix: Recalled vehicles will undergo preventive reprogramming of the injection computer

469 vehicles · built 1 Sep 2002 to 22 Jun 2004

In certain cases the front brake flexible hoses may be located too close to the front discs and become worn through contact with them. This poses the risk of a deterioration of brake performance.

Fix: Recalled vehicles will have the front brake flexible hose retaining brackets replaced.

300 vehicles · built 20 Mar 2003 to 20 Apr 2004

In certain cases the risk exists that there may be a faulty contact between the accelerator pedal sensor and the injection computer. In such cases the SERV warning light will illuminate on the dashboard.The situation remains under control by simply by applying the brake pedal.

Fix: Recalled vehicles will undergo preventive reprogramming of the injection computer

469 vehicles · built 1 Sep 2002 to 22 Jun 2004

In certain cases the risk exists that there may be a faulty contact between the accelerator pedal sensor and the injection computer. In such cases the SERV warning light will illuminate on the dashboard.The situation remains under control by simply by applying the brake pedal.

Fix: Recalled vehicles will undergo preventive reprogramming of the injection computer

469 vehicles · built 1 Sep 2002 to 22 Jun 2004

It is possible that the steering wheel may become loose on the steering column mounting splines which could eventually damage the splines.

Fix: Recall affected vehicles replace the steering wheel and mounting bolt with quality assured items.

964 vehicles · built 2 Sep 2003 to 14 Apr 2004

It has been established that in certain cases the tightness of the steering wheel mounting may not be to specification.

Fix: Likely to be affected vehicles will be recalled at which time as a preventative measure the steering wheel will be replaced and it's mounting strengthened.

3,513 vehicles · built 2 Sep 2003 to 28 May 2004

There is a possibility that due to a manufacturing defect the high pressure fuel delivery pipes may rupture and leak fuel

Fix: Recall affected vehicles and replace fuel pipes with quality assured type

111 vehicles · built 16 Oct 2003 to 23 Feb 2004

Potential smell and emission of smoke from the dashboard vents

Fix: Recall affected vehicles for reprogramming and configuration of the air conditioning software

1,040 vehicles · built 1 Jun 2002 to 5 Nov 2003

Potential smell and emission of smoke from the dashboard vents

Fix: Recall affected vehicles for reprogramming and configuration of the air conditioning software

3,071 vehicles · built 1 Jun 2002 to 5 Nov 2003

There is a possibility that the seat belt may not lock when required

Fix: Recall affected vehicles to check and replace if necessary the lap safety belt reel on the dual passenger seat

76 vehicles · built 16 Jul 2003 to 17 Oct 2003

The engine may intermittently accelerate by itself and/or suffer instability of the idle speed.

Fix: Reprogramme the fuel injection computer software.

12,819 vehicles · built 1 May 2001 to 31 Oct 2002

The engine may intermittently accelerate by itself and/or suffer instability of the idle speed.

Fix: Reprogramme the fuel injection computer software.

2,198 vehicles · built 1 Jan 2001 to 31 Jul 2002

Due to a manufacturing defect there is a potential risk of the front right or left suspension arm breaking if subjected to an impact.

Fix: Check the manufacturing markings on the suspension arms and replace where found necessary.

1,887 vehicles · built 7 Oct 2002 to 9 Oct 2002

It is possible that the handbrake may not be fully effective when the vehicle is parked.

Fix: Reprogramme the parking brake computer software.

359 vehicles · built 1 Jan 2003 to 4 Mar 2003

The pipe connection on the non return valve fitted to the park brake circuit may separate from the connector due to a manufacturing defect. This could cause unintended application of the parking brake.

Fix: Fit a replacement quality assured non return valve.

233 vehicles · built 17 Feb 2003 to 24 May 2003

The studs securing the front and rear brake chambers may have received the incorrect heat treatment. As a consequence a brake chamber could become detached from it's mounting bracket.

Fix: Check and replace the front and rear brake chambers where found necessary.

408 vehicles · built 13 Jan 2003 to 24 Apr 2003

The studs securing the front and rear brake chambers may have received the incorrect heat treatment. As a consequence a brake chamber could become detached from it's mounting bracket.

Fix: Check and replace the front and rear brake chambers where found necessary.

408 vehicles · built 13 Jan 2003 to 24 Apr 2003

The studs securing the front and rear brake chambers may have received the incorrect heat treatment. As a consequence a brake chamber could become detached from it's mounting bracket.

Fix: Check and replace the front and rear brake chambers where found necessary.

408 vehicles · built 13 Jan 2003 to 24 Apr 2003

Brake servo may fail resulting in a hard brake pedal due to the loss of power assistance.

Fix: Replace the brake servo unit.

2,803 vehicles

There is a risk of a loss of brake servo assistance due to the incorrect positioning of the air pressure sensor in the inlet manifold.

Fix: Check the position of the air pressure sensor and correct where necessary.

1,861 vehicles · built 16 Apr 2002 to 27 Jun 2002

There is a risk of a loss of brake servo assistance due to the incorrect positioning of the air pressure sensor in the inlet manifold.

Fix: Check the position of the air pressure sensor and correct where necessary.

1,861 vehicles · built 16 Apr 2002 to 27 Jun 2002

Risk of loss of service brake due to securing clips missing from the brake pedal to servo cross shaft linkage.

Fix: Examine brake pedal cross shaft installation and replace any missing clips.

816 vehicles

The engine speed may surge intermittently when first started from cold when the outside temperature is between 0 degrees centigrade and plus 5 degrees centigrade.

Fix: Reprogramme the fuel injection computer.

1,646 vehicles · built 1 May 2002 to 31 Jul 2002

The spare wheel winch cable may seize or break and allow the wheel to fall onto the road.

Fix: Fit a modified spare wheel support cross member and winch unit.

6,597 vehicles · built 1 Sep 1996 to 11 Dec 1998

It is possible for water to enter the braking system via the cap of the brake fluid reservoir or via a vent hole between the boosters and master cylinders. Resultant vapour locks and/or corrosion of internal components could render the footbrake ineffective under arduous operating conditions.

Fix: Modify the brake fluid reservoir filler caps and master cylinder/booster venting arrangements to prevent the ingress of water.

1,209 vehicles

It is possible for water to enter the braking system via the cap of the brake fluid reservoir or via a vent hole between the boosters and master cylinders. Resultant vapour locks and/or corrosion of internal components could render the footbrake ineffective under arduous operating conditions.

Fix: Modify the brake fluid reservoir filler caps and master cylinder/booster venting arrangements to prevent the ingress of water.

1,209 vehicles

The engine may stall at idle and/or when lifting off the throttle following a period of hard acceleration.

Fix: Check the serial number on the fuel pressure regulator and replace it if it is within the affected range.

1,861 vehicles · built 1 Nov 2000 to 31 May 2001

The electrical connections to the side air bags may be transposed. This could result in the air bag on the opposite side to an impact being deployed.

Fix: Check side air bag wiring for transposed connections and correct where necessary.

3,609 vehicles · built 1 Oct 1999 to 1 May 2000

The air bag control electrical wiring attached to the drivers swivelling seat may become damaged and cause unscheduled deployment of the drivers' air bag.

Fix: Examine wiring for damage and re-route and secure as necessary

467 vehicles · built 1 Jan 1999 to 30 Jul 1999

1) Accelerator pedal may stick in the open position. (Petrol and diesel engine models). 2) Engine may stall at idle or after hard acceleration. (Diesel engine models).

Fix: 1) Reposition pad at base of accelerator. 2) Repalce the pressure regulator valve on the diesel fuel pump.

1,646 vehicles

Laguna II's fitted with the 1.6 16v engine may cut out and stall at idle/lift off when the air conditioning is switched on.

Fix: Rectified by recalibrating the injection computer.

4,838 vehicles · built 1 Oct 2000 to 27 Jun 2001

Danger of leakage from the Diesel injection high pressure pipes which can result in destruction of the Emergency Brake Assist connector located on the Brake Booster.

Fix: Replace diesel fuel injection high pressure rail and pipes and Emergency Brake Assist connector seal at Brake Booster Unit.

2,249 vehicles

Non air conditioned Megane and Scenics equipped with K4J or K4M engines with a pre-catalytic convertor fitted may have a hard brake pedal (lack of braking assistance). This is caused by the deterioration of the braking assistance pipe as it passes too close to the source of heat emitted by the pre-catalytic convertor.

Fix: Recall affected vehicles and replace and/or reroute the brake assistance (vacuum) pipe.

11,960 vehicles

Vehicles fitted with 1.4 16v engines and having the MGI motorised throttle housing and Sirius 34 injection computer may have engine hesitation and idling speed instability. This due to incorrect locking of the connector to the throttle housing causing instability in the operation of the injection system.

Fix: Rectified by replacing the motorised throttle housing connector.

1,574 vehicles

Non air conditioned Megane and Scenics equipped with K4J or K4M engines with a pre-catalytic convertor fitted may have a hard brake pedal (lack of braking assistance). This is caused by the deterioration of the braking assistance pipe as it passes too close to the source of heat emitted by the pre-catalytic convertor.

Fix: Recall affected vehicles and replace and/or reroute the brake assistance (vacuum) pipe.

11,960 vehicles

Vehicles fitted with 1.4 16v engines and having the MGI motorised throttle housing and Sirius 34 injection computer may have engine hesitation and idling speed instability. This due to incorrect locking of the connector to the throttle housing causing instability in the operation of the injection system.

Fix: Rectified by replacing the motorised throttle housing connector.

1,574 vehicles

Vehicles fitted with 1.4 16v engines and having the MGI motorised throttle housing and Sirius 34 injection computer may have engine hesitation and idling speed instability. This due to incorrect locking of the connector to the throttle housing causing instability in the operation of the injection system.

Fix: Rectified by replacing the motorised throttle housing connector.

1,574 vehicles

Customers may find that they are unable to secure the front and side doors of their vehicles due to wear of the locking bolt due to omission of heat treatment.

Fix: Rectified by replacing both the front and side door locks.

1,445 vehicles · built 23 May 2001 to 30 Jun 2001

Customers may find that they are unable to secure the front and side doors of their vehicles due to wear of the locking bolt due to omission of heat treatment.

Fix: Rectified by replacing both the front and side door locks.

1,445 vehicles · built 23 May 2001 to 30 Jun 2001

The front suspension stabiliser bar brackets may fracture.

Fix: Replace both front stabiliser bar brackets.

205 vehicles · built 1 Jun 2001 to 18 Jul 2001

There is a risk of the diesel return pipe rubbing against the alternator and there is a risk of leakage from the connections of the high pressure pipes to the injectors. It is possible that the high pressure pump supply pipe may wear against the acoustic protector.

Fix: Reposition or replace any chafing fuel pipes as appropriate. Check the union connections for correct tightness on the high pressure pipes to the injectors.

3,586 vehicles

There is a risk of the diesel return pipe rubbing against the alternator and there is a risk of leakage from the connections of the high pressure pipes to the injectors. It is possible that the high pressure pump supply pipe may wear against the acoustic protector.

Fix: Reposition or replace any chafing fuel pipes as appropriate. Check the union connections for correct tightness on the high pressure pipes to the injectors.

3,586 vehicles

There is a possibility that one of the four securing bolts may be missing which could cause incorrect deployment of the air bag during operation.

Fix: Recall affected vehicles and replace any missing air bag securing bolts.

894 vehicles · built 27 Jul 2000 to 29 Jul 2000

The towing ball mounting panel may flex under load and eventually crack causing the towing ball to become insecure.

Fix: Recall affected vehicles to fit towing ball mounting panel reinforcement kit.

226 vehicles · built 27 Nov 2000 to 25 Dec 2000

The accelerator cable may break and cause a sudden loss of engine power.

Fix: Recall affected vehicles and fit a modified accelerator cable.

105,883 vehicles · built 1 Jan 1998 to 28 Dec 1999

Quality inspections by the manufacturer have revealed the possibility of a faulty connection between the high tension leads and the ignition coil. The connector could overheat if not replaced.

Fix: Recall affected vehicles and replace the ignition harness and ignition coil.

771 vehicles · built 15 Sep 1999 to 8 Feb 2001

The camshaft sensor may fail and cause the engine to cut out

Fix: Affected vehicles are being recalled for replacement of the camshaft sensor.

771 vehicles · built 15 Sep 1999 to 8 Feb 2001

Engine exhaust gas recirculation pipe may fail and cause the vehicle to hesitate when pulling away.

Fix: Recall affected vehicles and replace the exhaust gas recirculation pipe.

771 vehicles · built 15 Sep 1999 to 8 Feb 2001

Fuel leakage from the fuel pipes and common rail may occur at high pressure.

Fix: Affected vehicles are being recalled for replacement of the fuel pipes and rail with quality assured components.

771 vehicles · built 15 Sep 1999 to 8 Feb 2001

There is a possibility of the fastener attaching the brake caliper to the Stub Axle coming loose on the rear wheels due to a mismatch between the Stub Axle and the fastener. This can adversely affect the performance of the fastener and may lead to a loss of efficiency in the braking system.

Fix: Recall affected vehicles and replace original fastener with a modified type and a lock washer to prevent it coming loose.

1,090 vehicles · built 17 Jul 2000 to 20 Sep 2000

A fault within the control unit may cause unintentional deployment of the front air bags and or seat belt pre-tensioners.

Fix: Recall affected vehicles and fit a quality assured control unit.

14,046 vehicles · built 23 Dec 1998 to 26 May 2000

A fault within the control unit may cause unintentional deployment of the front air bags and/or seat belt pre-tensioners.

Fix: Recall affected vehicles and fit a quality assured control unit.

14,046 vehicles · built 23 Dec 1998 to 26 May 2000

There is a possibility of a rapid loss of tyre pressure on Kleber C100 165/70 R14 85 R tyres due to low inner rubber thickness on casing ply cord in tyre shoulder zone. This may affect the vehicle's road holding.

Fix: Recall affected vehicle's and replace tyres with quality assured tyre.

969 vehicles · built 1 Apr 2000 to 30 Jul 2000

The computer which controls the deployment of the Airbags may be incorrectly programmed. The Airbags may inadvertently deploy.

Fix: Recall affected vehicles and change the computer which controls the deployment of the Airbags.

17 vehicles

A specific batch of vacuum pumps may have a potential defect (blockage) which may cause a reduction in servo assistance.

Fix: Recall affected vehicles and replace vacuum pump.

10,425 vehicles · built 1 Feb 2000 to 30 Apr 2000

A specific batch of vacuum pumps may have a potential defect (blockage) which may cause a reduction in servo assistance.

Fix: Recall affected vehicles and replace vacuum pump.

10,425 vehicles · built 1 Feb 2000 to 30 Apr 2000

A specific batch of vacuum pumps may have a potential defect (blockage) which may cause a reduction in servo assistance.

Fix: Recall affected vehicles and replace vacuum pump.

10,425 vehicles · built 1 Feb 2000 to 30 Apr 2000

A specific batch of vacuum pumps may have a potential defect (blockage) which may cause a reduction in servo assistance.

Fix: Recall affected vehicles and replace vacuum pump.

10,425 vehicles · built 1 Feb 2000 to 30 Apr 2000

The roof bars may fail when loaded to the limit of their carrying capacity. Failure could result in loss of luggage.

Fix: Affected vehicles are being recalled to have the original roof bars replaced with quality assured examples.

4,000 vehicles · built 1 Jun 1997 to 30 Sep 1997

There is a possibility of a restriction in a plastic double pipe union on the brake master cylinder. This could prevent or reduce the operation of the hydraulic braking circuit.

Fix: Affected vehicles are being recalled to have the plastic union examined for evidence of any restriction. If a restriction is found the plastic pipe union will be replaced with a quality assured version.

7,434 vehicles · built 1 Jul 1997 to 30 Sep 1997

There is a possibility of a restriction in a plastic double pipe union on the brake master cylinder. This could prevent or reduce the operation of the hydraulic braking circuit.

Fix: Affected vehicles are being recalled to have the plastic union examined for evidence of any restriction. If a restriction is found the plastic pipe union will be replaced with a quality assured version.

7,434 vehicles · built 1 Jul 1997 to 30 Sep 1997

Wear in the area of the support bearings may lead to failure of the primary steering shaft and cause loss of directional control.

Fix: The affected vehicles are being recalled to have the original shaft replaced with a complete assembly.

12,500 vehicles · built 1 Mar 1989 to 30 Apr 1995

The ball joints on the steering track rods and on the suspension rear parallelism adjustment may not be fully secure.

Fix: The affected vehicles are being recalled to have the original securing bolts for the components concerned replaced with new examples.

34 vehicles · built 1 Jan 1996 to 31 Dec 1997

Under certain operating conditions the steering universal joint locking bolt may detach. This would affect directional control of the vehicle.

Fix: Recall the affected vehicles for replacement of the steering universal joint.

39 vehicles

On vehicles equipped with both driver and passenger air bags unscheduled illumination of the air bag warning light may occur in conditions of low ambient temperature.

Fix: Recall the affected vehicles for the fitment of a modified computer to the air bag system

551 vehicles · built 1 Jul 1995 to 31 Dec 1995

On vehicles equipped with both driver and passenger air bags unscheduled illumination of the air bag warning light may occur in conditions of low ambient temperature.

Fix: Recall the affected vehicles for the fitment of a modified computer to the air bag system

551 vehicles · built 1 Jul 1995 to 31 Dec 1995

There is a risk of scalding to occupants of the front seats as a result of hot coolant leaking from the heater matrix into the passenger compartment.

Fix: Recall the affected vehicles for inspection of the heater matrix. Where this is found to be of an unmodified design (visually apparent) it will be replaced with a modified unit.

730 vehicles · built 8 Jul 1991 to 23 Jul 1992

The welding on the front suspension arm locating lug may not be to the manufacturers specification.

Fix: Recall the affected vehicles and inspect the integrity of the subject welding. Where required the welding will be reworked to comply with the manufacturers specification.

28 vehicles · built 1 Jul 1991 to 31 Jan 1993

As a result of a quality problem in the manufacture of the front brake discs the vehicle may pull to the left when the footbrake is applied.

Fix: Recall the affected vehicles and replace both front brake discs with quality assured examples.

8,236 vehicles · built 1 Apr 1993 to 30 Jun 1994

Under certain circumstances the fuel filter outlet pipe union may contact the heating element fitted to the fuel filter body. This will result in a short circuit with possible fire risk.

Fix: Recall the subject vehicles for the inclusion of a fuse link in the fuel filter heating element circuit and the fitment of a clip to ensure that the filter outlet pipe union is held clear of the element body.

3,213 vehicles · built 1 Sep 1992 to 30 Sep 1994

The left hand fog light wiring loom may chafe in the area of the towing eye. This could cause a short circuit with possible risk of fire.

Fix: Recall the affected vehicles and check the condition of the loom adjacent to the towing eye. Where contact damage has occurred this will be repaired and in all cases the wiring loom will be protected by the addition of a foam rubber block

1,284 vehicles · built 1 May 1991 to 30 Jun 1992

Due to the effect of corrosion on the aluminium spacer at the master cylinder mounting it is possible for the brake master cylinder to detach from the airpac unit rendering one half of the service brake system inoperative.

Fix: Recall the affected vehicles for the fitment of a re-designed spacer to the brake master cylinder mounting.

1,110 vehicles · built 1 Jan 1988 to 31 Dec 1993

1) Bonnet catch securing bolts may slacken in service allowing movement of the lock mechanism. This may result in the bonnet lifting. 2) Autoliv-Klippan seat belt pre-tensioners may be faulty.

Fix: 1. Replace the bonnet catch fixing bolts with screws and lock nuts. 2. Substitute any Autoliv-Klippan pre-tensioners with TRW-REPA equipment.

29,661 vehicles · built 1 Apr 1992 to 31 Mar 1994

Incorrect positioning and/or tightening of the fuel pipe clips on the injection bar may cause petrol fumes or smell in the passenger compartment.

Fix: Recall the affected vehicles for inspection. Where the subject pipes have been incorrectly positioned and/or tightened the pipes will be replaced.

579 vehicles · built 1 Mar 1991 to 31 Dec 1991

Incorrect positioning and/or tightening of the fuel pipe clips on the injection bar may cause petrol fumes or smell in the passenger compartment.

Fix: Recall the affected vehicles for inspection. Where the subject pipes have been incorrectly positioned and/or tightened the pipes will be replaced.

579 vehicles · built 1 Mar 1991 to 31 Dec 1991

The front suspension upper mounting plate cups may crack. Under certain conditions this could affect vehicle handling.

Fix: Recall the affected vehicles for replacement of the front suspension upper mounting plates with examples incorporating an alternative metal specification.

4,247 vehicles

A batch of vehicles has been identified where the parking brake pawl teeth have been incorrectly formed and are of insufficient depth. This may result in damage to the pawl teeth as well as those on the handbrake ratchet and could permit spontaneous release

Fix: Recall the affected vehicles for replacement of the parking brake ratchet and pawl mechanisms with quality assured components. This recall supersedes former campaign R1992/17 since Renault have decided to replace the ratchet and pawl mechanisms on

872 vehicles

Possible fracture of the stub axle(s) on high mileage passenger carrying vehicles. This could result in loss of the wheel and hub assembly with attendant loss of vehicle control and braking effort on one brake circuit.

Fix: Recall the affected vehicles for replacement of the stub axle during normal routine servicing or repair with new units incorporating a revised heat treatment requirement.

900 vehicles

The front seat pivoting mechanism may not operate correctly. This may lead to imprecise locking of the front seats which under certain driving conditions may have safety implications if the driving seat is not retained in the normal driving mo

Fix: Recall affected vehicles for replacement of the seat pivot flange and the fitment of an additional ring washer on both front seats.

644 vehicles · built 1 Jan 1991 to 31 Dec 1991