Iveco recalls

The manufacturer has determined that affected vehicles may be fitted with a front-axle braking system that does not fully comply with the regulatory authority’s requirements.

Fix: Modification and optimisation of front axle brake lines on 4x2 vehicles.

• X WAY: vehicle count not given · built 27 Nov 2020 to 19 Nov 2024
• S WAY: 167 vehicles · built 27 Nov 2020 to 19 Nov 2024

The manufacturer has determined that affected vehicles have both an earlier version and a later more advanced version of the AEBS control software installed. This co-occurrence may result in different information being displayed on the diagnostic dashboard and these differences could be mistakenly interpreted as an error or a failure of the AEBS

Fix: Instrument Cluster Software update.

• EUROCARGO: 106 vehicles · built 28 Jul 2023 to 28 May 2025
• EUROCARGO: vehicle count not given · built 28 Jul 2023 to 28 May 2025

​Affected vehicles may have both an earlier version and a later more advanced version of the AEBS control software installed. This co-occurrence may result in different information being displayed on the diagnostic dashboard and these differences could be mistakenly interpreted as an error or a failure of the AEBS.

Fix: ​​Software update of all control units involved in the operation of ADAS systems.​

• EUROCARGO: vehicle count not given · built 23 Jun 2023 to 29 May 2025
• EUROCARGO: 84 vehicles · built 23 Jun 2023 to 29 May 2025

Affected vehicles may have been built with a fixation of the steering gearbox on the frame which can get loose due to an incorrect tightening torque.

Fix: Inspection of the steering gearbox fixation and a potential retightening or a substitution of the steering gearbox including the support and screws.

• S WAY: 30 vehicles · built 11 Jan 2024 to 2 Jun 2025
• X WAY: 2 vehicles · built 11 Jan 2024 to 2 Jun 2025

On affected vehicles the half shaft screws to rear axle may not be properly tightened. The screws could therefore loosen up to a partial or total decoupling of the half-shaft from the rear axle with possible loss of direction and control of the vehicle.

Fix: Re-tightening of the screws of the rear axle half shafts to the required value.

244 vehicles · built 1 Oct 2024 to 31 May 2025

On affected vehicles the Anti-lock Braking System (ABS) connections to the front wheels maybe be inverted this may result in an increased stopping distance and/or reduced vehicle stability control during braking that requires ABS intervention.

Fix: Check and reposition ABS cable connectors as required.

• EUROCARGO: vehicle count not given · built 1 Jul 2023 to 31 Mar 2025
• EUROCARGO: vehicle count not given · built 1 Jul 2023 to 31 May 2025

The manufacturer has determined that affected vehicles may have missing or incorrect rear suspension brackets and buffer installed onto the vehicle. This could result in increased roll with a possible loss of control that could result in a roll-over of the vehicle in extreme cases.

Fix: The remedial action is to replace the bracket with correct buffer.

21 vehicles · built 1 Jul 2023 to 30 Nov 2024

The vehicle may potentially be affected by an air leakage from the trailer hose due to detachment of the hose from the trailer hose coupling. If this event occurs it may result in an unexpected brakes activation on the trailer only.�

Fix: Installing 2 security hose clamps on both trailer hoses to avoid the potential detachment of hose/hoses from the trailer hose coupling.�

• S WAY RIGID: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023
• X WAY ARTIC: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023
• X WAY RIGID: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023
• S WAY ARTIC: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023
• T WAY RIGID: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023
• T WAY ARTIC: 1,914 vehicles · built 1 Mar 2022 to 30 Sep 2023

There is the potential for the rear axle pinion flange nut to loosen over time.

Fix: Inspect the condition of the pinion flange nut and if required rework the flange nut with the correct adjustment and crimping.

• T WAY RIGID: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023
• T WAY ARTIC: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023
• X WAY RIGID: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023
• S WAY RIGID: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023
• S WAY ARTIC: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023
• X WAY ARTIC: 90 vehicles · built 1 Feb 2022 to 31 Jan 2023

There is a potential that breakage of the steering lever brackets may occur due to defective welds.

Fix: Replace the steering lever bracket.

7 vehicles · built 1 Sep 2022 to 1 Dec 2022

The engine dataset may not comply with OBD (On board diagnostic) regulations.

Fix: Perform a software update of the engine dataset

4,837 vehicles · built 1 Nov 2018 to 30 Sep 2021

The mounting screws of the steering rack may become loose.

Fix: Replace the fastening screws of the hydraulic steering rack assembly to the front driving axle including an additional application of specific Loctite adhesive 243 to the securing screws.

63 vehicles · built 1 May 2019 to 30 Apr 2022

The cab tilt support may need to be replaced for its noncompliance of mating sub-assemblies (welding) on certain batch of vehicles.

Fix: Upgrade the cab tilt ram mounting bracket and in some cases apply corrective actions to replace the support.

393 vehicles · built 1 Jul 2022 to 30 Nov 2022

Potential damage to the front brake hose caused by an incorrect layout of the pipes

Fix: Visual check on the condition of the flexible pipe located in the area on the left front wheel side and in case of interference with the electric cable the pipe will be to be repositioned or replaced if worn / damaged.

1,547 vehicles · built 16 May 2019 to 29 Apr 2022

The Front axle leave spring retainers (U-Bolts) could work loose or may be lost during a driving cycle.

Fix: Retighten front axle U-Bolt with an increased torque

• STRALIS: 2,078 vehicles · built 1 Oct 2018 to 30 Sep 2022
• S WAY: 2,078 vehicles · built 1 Oct 2018 to 30 Sep 2022
• X WAY: 2,078 vehicles · built 1 Oct 2018 to 30 Sep 2022
• T WAY: 2,078 vehicles · built 1 Oct 2018 to 30 Sep 2022

Front suspension ball joint may not be to specification.

Fix: Check the front suspension ball joint play and if necessary replace the component.

179 vehicles · built 1 May 2022 to 31 May 2022

Incorrect monitoring of the urea tank temperature and Insufficient protection of the engine dataset in case of tampering.

Fix: Update of the ECU through a new software and update of the calibration software of the diagnosis of the urea tank temperature sensor.

6,483 vehicles · built 7 Dec 2018 to 6 Aug 2021

Incorrect monitoring of the urea tank temperature and Insufficient protection of the engine dataset in case of tampering.

Fix: Update of the ECU through a new software and update of the calibration software of the diagnosis of the urea tank temperature sensor.

3,989 vehicles · built 7 Dec 2018 to 6 Aug 2021

Poor performance of the fuel injection system due to a fuel contamination (not linked with a quality of the fuel itself).

Fix: Replacement of the fuel filter cartridge increasing the filtration system and testing the injectors. In case of checks with negative result the electro-injectors will be replaced.

6,728 vehicles · built 4 Apr 2016 to 13 Jun 2019

Possible lack of cotter pin on steering axle or possible wrong cotter pin assembly on steering axle.

Fix: Check and re-torque the nut and replacement of the cotter pin on the steering track rod.

11 vehicles · built 18 Dec 2020 to 12 Mar 2021

Possible incorrect or missing cotter pin on steered axle joint.

Fix: Check and re-torque the nut and replacement of the cotter pin on the steering rod.

• STRALIS: 75 vehicles · built 1 Dec 2020 to 31 Mar 2021
• S WAY: 75 vehicles · built 1 Dec 2020 to 31 Mar 2021
• X WAY: 75 vehicles · built 1 Dec 2020 to 31 Mar 2021

Driver's airbag warning light doesn't switch on in case of problems relating to the airbag system and related wiring.

Fix: Update vehicle software.

1,417 vehicles · built 18 Dec 2018 to 15 Oct 2019

A short circuit in the ABS can occur without warning when the engine is switched off.

Fix: Installing of a switch off relays to interrupt the power supply to the ABS ECU in vehicle key off condition.

• DAILY 4 X 2: 22 vehicles · built 8 Jun 1999 to 8 Nov 2010
• DAILY 4 X 4: 22 vehicles · built 17 Apr 2008 to 13 Feb 2014

Repeated interruptions of the particulate filter regeneration could lead to overheating of surrounding components.

Fix: Engine software update

4,588 vehicles · built 28 Apr 2016 to 10 Sep 2019

The Nox emission levels are higher than approval limits declared and repeated interruptions of the particulate filter regeneration could lead to overheating of surrounding components.

Fix: Engine software update.

2,463 vehicles · built 4 Apr 2016 to 15 Mar 2019

Exhaust gas temperatures may drop below the optimal operational level for the selective catalyst reduction affecting its efficiency when reducing nitrogen oxides.

Fix: Engine software update

• EUROCARGO: 1,632 vehicles · built 1 Aug 2013 to 1 Jul 2018
• EUROMIDI: 1,632 vehicles · built 1 Aug 2013 to 1 Jul 2018
• EUROFIRE: 1,632 vehicles · built 1 Aug 2013 to 1 Jul 2018

It has been identified that the Central Brake Unit and Rear Axle Modulator units may not function as intended. This can cause a higher braking retardation or quicker braking than anticipated. This can result in the vehicle stopping quicker that expected.

Fix: Recall all affected vehicles to check the production dates of the Central Brake Unit and Rear Axle Modulator units and change the units if found to be within the affected production range.

26 vehicles · built 1 Sep 2015 to 23 Aug 2016

On affected vehicles the eyelet connection of the parking brake secondary cable could break. If this happens the parking brake function can be affected

Fix: Inspect and where necessary replace cables.

1,702 vehicles

It is possible that under certain conditions the Momentum Stability Regulator (MSR) may not engage if the vehicle is driven too harshly. This could have an adverse affect on the stability of the vehicle and an unexperienced driver may loss control of the vehicle.

Fix: Recall all affected vehicle and upload a new version of the software.

1,649 vehicles

Possible fitting of a non-conforming fixing screw on the front axle of vehicles with Mecbal suspension systems. If the non-conforming screws are fitted in the worst case it is possible that the front axle could become insecure and the control of the vehicle lost.

Fix: Recall the vehicles that are likely to be affected to carry out checks of fixing screws and replace where necessary.

19 vehicles

It has been identified that the swivel head on the hydraulic operating cylinder for the second steer axle may not have been installed to IVECO's specification. This can cause fouling of other components which may affect the directional control of the vehicle.

Fix: Recall all affected vehicles to check and if required reposition the hydraulic operating cylinder swivel head.

258 vehicles

On-going research and quality checks have revealed that vehicles may be affected by possible interference between the brake hoses and the gearbox leading to potential brake hose abrasions and dispersion of brake fluid with decreased braking efficiency.

Fix: Vehicles will be inspected and brake hoses checked for damage. The retaining clips will be repositioned and if required brake hoses replaced.

1,384 vehicles

During one of the periodical design reviews an issue has been identified that theoretically could affect the vehicle in very particular circumstances. Should a fault in the parking braking system occur a degree of braking action could be applied by the system. This condition could potentially not be highlighted in the vehicle as the specific warning light could not be activated.

Fix: The cluster reprogramming rectifies the issue and ensures that even in particular conditions the information is correctly displayed through the warning light in the cluster.

6,412 vehicles

Some vehicles of the Eurocargo Euro 3 and MY2008 range may be subject to breakage of the rear shock absorber bottom support when used in demanding work situations. This will result in failed operation of the shock absorber.

Fix: To replace the defective rear shock absorber bottom support bracket within the listed chassis range with support brackets of correct conformity.

87 vehicles

Due to continuous quality control it has shown on a limited number of vehicles it may be necessary to replace a component of the brake valve EBS2 in order to ensure perfect efficiency of the braking system.Failure to replace the component described could compromise the correct operation of the braking system.

Fix: Replacement of the relay piston / sealing ring on the brake value of the EBS2 (CBU) tractor.

• STRALIS: 751 vehicles
• TRAKKER: 751 vehicles

On a number of vehicles the torque setting value of the retaining screws of the A frame guide rod joint to the axle could be wrong.

Fix: Checks to be carried out to ensure that the correct torque is applied.

• STRALIS: 605 vehicles · built 1 Jan 2011 to 31 Dec 2012
• TRAKKER: 605 vehicles · built 1 Jan 2011 to 31 Dec 2012

On vehicles equipped with electric cab tilting mechanism it is possible that water may enter the control relay for the system. This can cause a short circuit in the pump control relay which will operate the tilt pump and if the driver has failed to leave the control valve in the lowered position then an involuntary tilting of the cab may occur.

Fix: Recall all affected vehicles for the fitment of a water tight protection to be fitted to the control relay.

338 vehicles · built 1 Jan 2008 to 31 Dec 2011

On-going product and quality checks have shown that there may be defects in the Air suspension supports.

Fix: Check the supports for the air bellow manufacturing and casting numbers and replace i required.

366 vehicles

Bolts may be missing from the rear bumper support brackets which in a collision may cause the bumper not to function as intended and result in additional injuries.

Fix: Recall the vehicles that are likely to be affected to check and where necessary restore the correct fastening of the rear bumper support brackets.

22 vehicles · built 1 Jan 2008 to 31 Dec 2008

Fuel pipes may fail causing a leakage of fuel.

Fix: Replace all engine fuel pipes

• IRISBUS - ARWAY: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• EURORIDER: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• IRISBUS - CROSSWAY: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• IRISBUS - CITELIS: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• IRISBUS - EVADYS: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• IRISBUS - RECREO: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011
• IRISBUS - ACCESS-BUS: 100 vehicles · built 1 Jan 2008 to 31 Dec 2011

The hand brake release button can become detached from the ratchet control rod which prevents the pawl at the rear of the lever from engaging the ratchet. the hand brake must then be applied by the driver holding the lever in the engaged position.

Fix: Two solutions have been developed. a. re-fitment of using high strength loctite adhesive. b. Replacement of the button.

2,120 vehicles

It is possible that the side lights may extinguish within 30 seconds of the ignition being turned off even when the side lights have been selected. This could affect vehicle visibility during darkness.

Fix: Recall all affected vehicles to check side light function and if required modify the electrical wiring in the CVM unit.

1,131 vehicles

The second axle steering ram and/or clevis assembly may not be to specification which will result in some movement between the mounting and the ram. If ignored the movement will increase with usage and could eventually lead to separation of the ram and mounting resulting in the steering control being impaired.

Fix: Recall the vehicles that are likely to be affected to check and where necessary replace parts as indicated by the repair procedure issued by the manufacturer.

1,722 vehicles

Ingress of dirt into the steering shaft sliding joint will cause the splines to wear prematurely. As the joint wears play at the steering will become apparent and over time the play will increase leading to some pulsing when the steering wheel is turned and the vehicle wandering. If all these warning signs are ignored and the vehicle is still used there will be increased difficulty in maintaining steering control.

Fix: Recall the vehicles that are likely to be affected to replace the steering shaft with a modified type.

137 vehicles

Incorrectly fitted panhard rod mounting bolts may fail and lead to the rear axle developing lateral movement.

Fix: Recall the vehicles that are likely to be affected to fit new panhard rod mounting bolts to the correct torque.

11 vehicles

It has been identified that due to insufficient clearance between the prop shaft centre bearing flange and the cross member a foul condition may exist between the two. It is therefore possible that the flange could break with possible loss of drive and vehicle control.

Fix: Recalled vehicles will be fitted with new nuts and bolts and additional spacers fitted under the centre bearing which will give increased clearance between the prop shaft flange and the cross member.

12 vehicles · built 1 Jul 2008 to 31 Mar 2009

Steering control maybe affected by loose cab to chassis mountings.

Fix: Recall the vehicles that are likely to be affected to check and where necessary re-torque the bolts securing the cab to the chassis.

156 vehicles · built 1 Oct 2008 to 31 Oct 2008

Under extreme conditions the fifth wheel bed plate may flex and damage the fifth wheel base.

Fix: Recall affected vehicles replace the fifth wheel and bed plate if manufactured by GF

9 vehicles · built 1 Jul 2008 to 30 Sep 2008

It has been identified that the possibility exists that the Duo-Duplex brake adjusting mechanism may non operate correctly. Should this be the case possible loss of front and rear brake adjustment may occur which can result in loss of braking efficiency on both the service and parking brake systems.

Fix: Recalled vehicles will have the brake stations of both the front and rear axles fitted with a modified brake adjuster kit.

• TRAKKER: 291 vehicles · built 28 Jun 2005 to 31 Jan 2008
• TRAKKER: 291 vehicles
• TRAKKER: 291 vehicles · built 29 Jun 2007 to 29 Mar 2008

It has been identified that; the possibility exists that the fuel injector pipes may fracture leading to spillage of fuel within the engine bay and the risk of fire.

Fix: Recalled vehicles will be fitted with a new design of injector pipe manufactured from a different steel alloy.

198 vehicles · built 1 Oct 1998 to 31 May 2001

It has been identified that a brake pipe may have been incorrectly secured to the bulkhead with a plastic clip. As a consequence; under certain circumstancesthe brake pipes can vibrate out of the clips and could fracture resulting in a loss of braking efficiency.

Fix: Recalled vehicles will be fitted with a steel securing bracket which will have the addition of rubber insulation.

146 vehicles · built 6 Apr 2006 to 5 Feb 2008

It has been identified that the possibility exists; for the engine compartment cover seal to become dislodged during service. Should this occur the seal could fall onto the engine causing a fire.

Fix: Recalled vehicles will have the engine compartment cover seal checked for security and condition. It will be renewed as necessary or refitted using an adhesive.

95 vehicles · built 1 Nov 2001 to 30 Jun 2006

The Track Rod clamping bracket gaps may have closed before the correct torque has been reached which may allow the track rod to gradually work loose.

Fix: Recall affected vehicles to check and if action is required new clamping brackets will be fitted and bolts tightened to correct torque.

• A SERIES: 42 vehicles · built 13 Oct 2007 to 27 Oct 2007
• A SERIES: 42 vehicles · built 4 Dec 2007 to 4 Dec 2007

It is possible that the material used for the rear anti roll bar supports may be incorrect and could collapse causing serious stability concerns.

Fix: Recall the vehicles that are likely to be affected to replace both the rear anti roll bar supports.

• TRAKKER: 32 vehicles · built 1 Dec 2006 to 31 Jan 2007
• STRALIS: 32 vehicles · built 1 Dec 2006 to 31 Jan 2007

Some vehicles may have been fitted incorrect specification flexible brake hoses which if not checked and replaced could lead to a brake failure.

Fix: Recall all affected vehicles for inspection of the flexible brake hoses and replacement if found to be out of specification.

• DAILY: 996 vehicles · built 16 Oct 2007 to 22 Nov 2007
• DAILY: 996 vehicles · built 22 Oct 2007 to 22 Nov 2007

It has been identified that the possibility exists that the contacts in the cab wiring loom may oxidize and cause overheating of the connector block. In the worst case this may result in a fire.

Fix: Recalled vehicles will have the suspect wires removed from the connector block. Theses will then be reconnected using heat shrink terminals.

12,045 vehicles · built 1 Jun 2001 to 31 May 2003

It has been identified that the possibility exists that the driver will not receive a warning signal should the trailer direction indicator lamp/s fail.

Fix: Recalled vehicles will have the trailer lighting control unit replaced.

• DAILYBUS: 22 vehicles · built 1 Dec 2006 to 31 Mar 2007
• DAILYBUS: 22 vehicles · built 1 Sep 2006 to 30 Apr 2007

It has been identified that on a limited number of vehicles the rear axle leaf spring mountings may crack or fracture. Should this occur vehicle stability could be affected.

Fix: Recalled vehicles will be inspected and repaired as required.

• DAILY: 287 vehicles · built 1 Nov 2000 to 30 Sep 2005
• DAILY: 287 vehicles · built 1 Nov 2003 to 31 May 2006

There is a possibility that the side repeater lamps may not work.

Fix: Recall the vehicles that are likely to be affected and reprogramme the computer to allow the side repeater lamps to activate.

• BUS: 22 vehicles · built 1 Sep 2006 to 31 Dec 2006
• DAILY: 22 vehicles · built 1 Sep 2006 to 31 Dec 2006

It is possible for the for the exhaust silencer strap bolts to slacken which if not rectified could lead to the total failure of the silencer mounting.

Fix: Recall the vehicles that are likely to be affected to replace the mounting bolts with new pre-coated bolts (locking compound) and tighten to the correct torque.

• STRALIS: 152 vehicles · built 1 Nov 2005 to 31 Jan 2007
• EUROTREKKER: 152 vehicles · built 1 Nov 2005 to 31 Jan 2007
• EUROTREKKER: 152 vehicles · built 1 Nov 2005 to 31 Dec 2006
• STRALIS: 152 vehicles · built 1 Nov 2005 to 31 Dec 2006