Iveco Eurocargo recalls

The manufacturer has determined that affected vehicles have both an earlier version and a later more advanced version of the AEBS control software installed. This co-occurrence may result in different information being displayed on the diagnostic dashboard and these differences could be mistakenly interpreted as an error or a failure of the AEBS

Fix: Instrument Cluster Software update.

• EUROCARGO: 106 vehicles · built 28 Jul 2023 to 28 May 2025
• EUROCARGO: vehicle count not given · built 28 Jul 2023 to 28 May 2025

​Affected vehicles may have both an earlier version and a later more advanced version of the AEBS control software installed. This co-occurrence may result in different information being displayed on the diagnostic dashboard and these differences could be mistakenly interpreted as an error or a failure of the AEBS.

Fix: ​​Software update of all control units involved in the operation of ADAS systems.​

• EUROCARGO: vehicle count not given · built 23 Jun 2023 to 29 May 2025
• EUROCARGO: 84 vehicles · built 23 Jun 2023 to 29 May 2025

On affected vehicles the Anti-lock Braking System (ABS) connections to the front wheels maybe be inverted this may result in an increased stopping distance and/or reduced vehicle stability control during braking that requires ABS intervention.

Fix: Check and reposition ABS cable connectors as required.

• EUROCARGO: vehicle count not given · built 1 Jul 2023 to 31 Mar 2025
• EUROCARGO: vehicle count not given · built 1 Jul 2023 to 31 May 2025

Possible lack of cotter pin on steering axle or possible wrong cotter pin assembly on steering axle.

Fix: Check and re-torque the nut and replacement of the cotter pin on the steering track rod.

11 vehicles · built 18 Dec 2020 to 12 Mar 2021

Exhaust gas temperatures may drop below the optimal operational level for the selective catalyst reduction affecting its efficiency when reducing nitrogen oxides.

Fix: Engine software update

1,632 vehicles · built 1 Aug 2013 to 1 Jul 2018

During one of the periodical design reviews an issue has been identified that theoretically could affect the vehicle in very particular circumstances. Should a fault in the parking braking system occur a degree of braking action could be applied by the system. This condition could potentially not be highlighted in the vehicle as the specific warning light could not be activated.

Fix: The cluster reprogramming rectifies the issue and ensures that even in particular conditions the information is correctly displayed through the warning light in the cluster.

6,412 vehicles

Some vehicles of the Eurocargo Euro 3 and MY2008 range may be subject to breakage of the rear shock absorber bottom support when used in demanding work situations. This will result in failed operation of the shock absorber.

Fix: To replace the defective rear shock absorber bottom support bracket within the listed chassis range with support brackets of correct conformity.

87 vehicles

On vehicles equipped with electric cab tilting mechanism it is possible that water may enter the control relay for the system. This can cause a short circuit in the pump control relay which will operate the tilt pump and if the driver has failed to leave the control valve in the lowered position then an involuntary tilting of the cab may occur.

Fix: Recall all affected vehicles for the fitment of a water tight protection to be fitted to the control relay.

338 vehicles · built 1 Jan 2008 to 31 Dec 2011

Bolts may be missing from the rear bumper support brackets which in a collision may cause the bumper not to function as intended and result in additional injuries.

Fix: Recall the vehicles that are likely to be affected to check and where necessary restore the correct fastening of the rear bumper support brackets.

22 vehicles · built 1 Jan 2008 to 31 Dec 2008

Incorrectly fitted panhard rod mounting bolts may fail and lead to the rear axle developing lateral movement.

Fix: Recall the vehicles that are likely to be affected to fit new panhard rod mounting bolts to the correct torque.

11 vehicles

It has been identified that due to insufficient clearance between the prop shaft centre bearing flange and the cross member a foul condition may exist between the two. It is therefore possible that the flange could break with possible loss of drive and vehicle control.

Fix: Recalled vehicles will be fitted with new nuts and bolts and additional spacers fitted under the centre bearing which will give increased clearance between the prop shaft flange and the cross member.

12 vehicles · built 1 Jul 2008 to 31 Mar 2009

Steering control maybe affected by loose cab to chassis mountings.

Fix: Recall the vehicles that are likely to be affected to check and where necessary re-torque the bolts securing the cab to the chassis.

156 vehicles · built 1 Oct 2008 to 31 Oct 2008

It has been identified that the possibility exists that the contacts in the cab wiring loom may oxidize and cause overheating of the connector block. In the worst case this may result in a fire.

Fix: Recalled vehicles will have the suspect wires removed from the connector block. Theses will then be reconnected using heat shrink terminals.

12,045 vehicles · built 1 Jun 2001 to 31 May 2003

Steering control could be lost on vehicles that have been fitted with none quality assured steering column shafts.

Fix: Recall the vehicles that are likely to be affected to check and if necessary replace the steering column shaft.

2,876 vehicles · built 19 Mar 2004 to 4 Nov 2004

It has been identified that if the incorrect type of cold start element is fitted frequent use under extreme weather conditions may lead to overheating of the control relay.

Fix: Recalled vehicles will have the part number of the cold start element checked which will be replaced as necessary.

693 vehicles · built 1 Jun 2006 to 31 Dec 2006

It is possible that the rear seat belt for the rear seats may be too small and not possible to fasten by certain persons

Fix: Recall affected vehicles and replace Seat Belts with correct type.

197 vehicles · built 1 Aug 2003 to 31 Mar 2006

It has been identified that an insufficient tightening torque mat have been applied to the bolts of the cab to chassis front mountings. This can cause the mounting bolts to work loose and the cab to shudder which may affect steering control.

Fix: Recalled vehicles will have the cab front mounting bolts checked for the correct tightening torque.

12 vehicles · built 1 Apr 2005 to 30 Jun 2005

It is possible in an emergency braking situation with fully laden vehicle the rear axle brakes will not be applied as expected giving a rise of extended braking distance.

Fix: Recall the vehicles that are likely to be affected and check the brake pressure regulator type fitted to the vehicle is the same as that list on the vehicle plate. If necessary fit a new plate. Check and if necessary adjust the load sensing valve linkage.

4 vehicles · built 1 Oct 2004 to 30 Nov 2004

There is insufficient surface area on the removable link between the two 30 amp heated windscreen fuses. This can resulting in the fuses being overheated.

Fix: Recalled vehicles will have a new connection made between the fuse holder pins.

57 vehicles · built 31 May 2000 to 29 Jul 2003

It is possible for the Grid Heater Control Unit not to function correctly and cause overheating of the units mounting compound.

Fix: Recall the vehicles that are likely to be affected and fit a modified Engine Grid Heater Relay and bracket.

5,081 vehicles · built 24 Aug 2004 to 13 Jun 2005

The possibility exists that water may ingress the ADR battery main relay. This may cause corrosion and the engine to stall.

Fix: Recalled vehicles will be fitted with a new battery connecting lead.

3 vehicles

There is a possibility that the airlines have been connected incorrectly which may lead to the emergency braking system becoming inoperative.

Fix: Recall the vehicles that are likely to be affected and check the airline position of the airline connections. If the connections are incorrect they will be connected to the correct positions.

1,492 vehicles · built 15 Oct 2002 to 29 Nov 2004

The possibility exists that a footvalve securing bolt is missing or has been incorrectly tightened which can lead to pedal operation being hindered thus affecting braking.

Fix: Recall likely to be affected vehicles and check that all the footvalve securing bolts are in place. If this is not the case a replacement bolt will be fitted. In any event the bolts will be checked for the correct torque.

768 vehicles

Possibility that contacts within the CAD loom may oxidize and cause overheating of the connectors

Fix: Recall likely to be affected vehicles check the connectors and reposition them within the wiring loom.

12,656 vehicles · built 1 May 2001 to 1 Mar 2003

The possibility exists for the ABS warning lamp not to illuminate despite there being a fault in the circuit

Fix: Recall likely to be affected vehicles and update instrument cluster with new software

6 vehicles · built 29 Jul 2003 to 7 Oct 2003

There is a possibility of loss of engine performance

Fix: Recall affected vehicles and reprogramme new software for Engine Control unit

47 vehicles · built 1 Feb 2003 to 2 Feb 2003

There is a possibility of the wiring terminal to the earth lead connections in the cab coming loose. This could cause intermittent electrical faults.

Fix: Check and where necessary tighten the earth connection.

118 vehicles · built 1 May 2003 to 30 Jun 2003

It is possible for the electrical cable between the battery and the starter motor to foul on the exhaust system.

Fix: Fasten the cable to the vehicle chassis with a dedicated bracket.

86 vehicles · built 1 Apr 2000 to 30 Jun 2001

Power steering flexible return hose may chafe on the engine crankshaft pulley.

Fix: Recall affected vehicles and fit a bracket to hold the return hose away from the pulley.

185 vehicles · built 1 Jan 2001 to 30 Jun 2001

The rear brake caliper retaining bolts may have been under torqued.

Fix: Recall affected vehicles and check the tightness of the relevant bolts. Renew any bolts found to be under torqued.

87 vehicles · built 1 Jan 1999 to 31 Dec 2000

The front brake cylinder may have been installed with the chamber breather hole uppermost. This could lead to the ingress of water and subsequent corrosion of the brake cylinder.

Fix: Recall affected vehicles and renew all front brake cylinders installed with the breather holes uppermost.

443 vehicles · built 1 Jan 1999 to 31 Dec 2000