Toyota Yaris recalls

For certain vehicles equipped with the combination meter system (where various information is displayed) that due to an improper programming of the combination meter unnecessarily repetitive data is written to a memory device. This may cause the memory device to deteriorate and the monitor to not display during the meter at start up and remain in this state permanently.

Fix: Reprogram or replace the combination meter.

7,210 vehicles · built 23 Mar 2023 to 26 Feb 2025

On affected vehicles there is a possibility that the DCM may not complete the shutdown process within a specific period of time when the ignition is turned off causing the DCM to not restart at the next ignition cycle and making the e-Call function unavailable. As a result the vehicles do not comply with relevant regulations.

Fix: The software of the DCM (Data Communication Module) will be updated via an Over the Air (OTA) wireless update.

27,327 vehicles · built 30 Jun 2021 to 28 Jul 2023

Affected vehicles have wheel nuts on the right-side front and rear wheels may not have been torqued correctly due to improper tightening of the nuts when installing the wheels at the vehicle assembly plant.

Fix: Check and tighten wheel nuts.

63 vehicles · built 13 Jun 2023 to 21 Jun 2023

The initialization of the radar sensor may not have been completed correctly.

Fix: Inspect the radar sensor and if necessary properly initialize the radar sensor.

42,554 vehicles · built 6 Jul 2020 to 21 Jun 2021

The emergency calling system (eCall) may not function when required.

Fix: Inspect the emergency calling system and update DCM software. If the DCM is found to be damaged replace it with updated software.

• YARIS: 26,575 vehicles · built 16 Jul 2020 to 26 Mar 2021
• YARIS: 26,575 vehicles · built 30 Sep 2020 to 5 Mar 2021

There is a possibility that the centre rear seat belt may be damaged a sharp edge of the bracket.

Fix: Add a protective material to the seat belt anchor bracket.

4,015 vehicles · built 8 Jul 2020 to 2 Oct 2020

It may not be possible to switch headlights from high beam to low beam or low beam to high beam.

Fix: Replace the Headlamp Units

106 vehicles · built 2 Jun 2020 to 19 Jun 2020

The absorption of moisture into the driver�s airbag propellant could lead to slow deployment or inflator rupture

Fix: Replace the airbag inflator or the airbag assembly. Toyota is still preparing for the development and production of the remedy parts

37,586 vehicles · built 28 Sep 1998 to 31 May 1999

A loss of injector sealing and resulting in fuel leakage.

Fix: Replace the injector spacer and bolts with new ones of the correct specification

99 vehicles · built 18 Jul 2017 to 12 Apr 2018

Vehicles may be equipped with front passenger airbag inflators not appropriate for the vehicles

Fix: Inspect and replace the affected parts if necessary

725 vehicles · built 10 Feb 2003 to 4 Oct 2005

The hybrid system could shut down resulting in loss of motive power

Fix: Inspect and replace the DC-DC converter with new one if necessary

3,274 vehicles · built 6 Feb 2018 to 2 Apr 2019

The front seat side airbags could be deactivated and/or the curtain airbags may not operate as intended.

Fix: Inspect the front door wire harness and replace if necessary.

1,472 vehicles · built 30 Jun 2014 to 17 Feb 2017

Passenger air bag may cause injury if activated.

Fix: Replace affected air bag assembly.

99,588 vehicles · built 24 Jan 2001 to 4 Nov 2004

On affected vehicles the drivers front airbag inflator could produce excessive internal pressure. If an affected airbag deploys the increased internal pressure may cause the inflator to rupture. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.

Fix: Recall the vehicles that are likely to be affected and replace the inflator inside the drivers airbag module with a new one.

449 vehicles · built 19 Dec 2002 to 1 Dec 2003

There is a possibility that a strut top mounting bearing could be damaged when a high load is applied to the strut such as when the vehicle is driven over a large bump. If this occurs there could be abnormal noise when driving on uneven roads or when turning the steering wheel. If the vehicle continues to be operated the upper side of the strut rod could separate causing a loss of vehicle stability which could increase the risk of a crash.

Fix: Recall the vehicles that are likely to be affected and replace the strut mounting bearings with improved ones. If a strut mounting bearing is found to be damaged the dealer will replace the strut and front suspension support sub-assembly with a new one.

5,526 vehicles · built 13 Jan 2015 to 27 Feb 2015

The vehicles are equipped with 3-point lap-shoulder belt assemblies in all-three rear seating positions. The inner belt (buckle portion) of each of the rear three seat belt assemblies is secured to the floor of the vehicle with an anchor plate. The anchor plate might have been manufactured with a sharp edge around the punched portion. In the event of a collision there is a possibility that the inner seat belt webbing could become cut and separate at the anchor plate. If this occurs the inner seat belt may not properly restrain the occupant which could increase the risk to injury.

Fix: Recall the vehicles that are likely to be affected and check the Lot number of the anchor plate. Where necessary the rear inner belt assembly will be replaced with a new one.

3,709 vehicles · built 30 Aug 2011 to 26 Jan 2016

Affected vehicles are equipped with a driver�s side Power Window Master Switch (PWMS) containing sliding electrical contact modules. These modules may not have been incorrectly coated during the manufacturing process. This may cause a short circuit which could cause the switch to overheat and melt

Fix: Inspect switch and apply coating. If switch indicates signs of malfunction it should be replaced.

123,306 vehicles · built 13 Jun 2005 to 31 Dec 2010

Subject vehicles are fitted with driver's air bag assemblies with single stage inflators. There is an increases potential for moisture ingress which could make the inflator more susceptible to rupture during deployment. Fragments may injure occupants.

Fix: Recall the vehicles that are likely to be affected to replace the airbag.

• YARIS: 63,332 vehicles · built 5 Jan 2015 to 22 Feb 2017
• YARIS: 1 vehicle · built 24 Aug 2011 to 30 Dec 2014
• YARIS: vehicle count not given · built 2 Jul 2003 to 30 Dec 2005
• YARIS: vehicle count not given · built 30 Dec 2005 to 14 Nov 2008

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to replace the airbag.

• YARIS: 542,751 vehicles · built 5 Jan 2009 to 30 Dec 2009
• YARIS: 542,751 vehicles · built 6 Jan 2010 to 30 Jul 2011
• YARIS: 542,751 vehicles · built 2 Apr 2007 to 25 Aug 2008
• YARIS: 542,751 vehicles · built 2 Apr 2007 to 14 Dec 2008
• YARIS: 542,751 vehicles · built 1 Feb 2001 to 30 Mar 2007

One or more of the rear hub retaining bolts may have not been tightened to the correct specification. A bolt or bolts may work loose and could have an adverse affect on the braking performance or could cause a wheel to lock unintentionally.

Fix: Recall affected vehicles. Check bolts for tightness and if required tighten to correct specification. Where necessary replace bolts.

• YARIS: 135 vehicles · built 12 Sep 2014 to 11 Dec 2014
• YARIS: 135 vehicles · built 10 Sep 2014 to 22 Dec 2014
• YARIS: 135 vehicles · built 17 Sep 2014 to 14 Oct 2014
• YARIS: 135 vehicles · built 15 Sep 2014 to 8 Nov 2014
• YARIS: 135 vehicles · built 16 Sep 2014 to 5 Jan 2015
• YARIS: 135 vehicles · built 8 Sep 2014 to 9 Jan 2015
• YARIS: 135 vehicles · built 11 Sep 2014 to 7 Jan 2015
• YARIS: 135 vehicles · built 9 Sep 2014 to 8 Jan 2015
• YARIS: 135 vehicles · built 12 Sep 2014 to 12 Dec 2014
• YARIS: 135 vehicles · built 10 Sep 2014 to 7 Jan 2015
• YARIS: 135 vehicles · built 23 Sep 2014 to 23 Sep 2014
• YARIS: 135 vehicles · built 13 Sep 2014 to 7 Jan 2015

Oil may accumulate in the turbo charger and in certain circumstances flow into the combustion chamber. This may cause engine damage. In extreme cases oil can be ejected from the engine and if it comes in contact with an ignition source may result in a fire.

Fix: Depending vehicle diagnosis modify intercooler layout to improve air flow; upgrade ECU software; upgrade turbo charger and/or vacuum pump

7,884 vehicles · built 13 Nov 2008 to 7 Sep 2013

On affected vehicles the drivers front airbag inflator could produce excessive internal pressure. If an affected airbag deploys the increased internal pressure may cause the inflator to rupture. In the event of an inflator rupture metal fragments could be propelled into the passenger compartment potentially causing injury to a vehicle occupant.

Fix: Recall the vehicles that are likely to be affected and replace the inflator inside the drivers airbag module with a new one.

• YARIS: 449 vehicles · built 19 Dec 2002 to 19 Dec 2002
• YARIS: 449 vehicles · built 2 Apr 2003 to 8 Dec 2003
• YARIS: 449 vehicles · built 19 Dec 2002 to 1 Dec 2003

Some front right hand brake callipers were produced with an incorrect chamfer dimension. With an incorrect chamfer it is possible that the oil seal gets damaged and that a brake fluid leak occurs. If a leak occurs the driver will notice the illumination of the brake warning lamps.

Fix: Recall the vehicles that are likely to be affected to replace the front right hand brake calliper.

22 vehicles · built 10 Apr 2014 to 15 Apr 2014

The steering column mounting bracket may not be of sufficient strength if the steering is repeatedly and forcibly turned on full lock. This over a prolonged period can result in the failure of the bracket and ultimate detachment of the steering column.

Fix: Recall all affected vehicles and replace the steering column mounting bracket.

• YARIS: 1,335 vehicles · built 19 Jul 2006 to 26 Feb 2009
• YARIS: 1,335 vehicles · built 22 Aug 2005 to 25 Dec 2008
• YARIS: 1,335 vehicles · built 19 Jul 2006 to 18 Feb 2009
• YARIS: 1,335 vehicles · built 21 Jan 2006 to 25 Jun 2009
• YARIS: 1,335 vehicles · built 8 Nov 2005 to 26 Jun 2009
• YARIS: 1,335 vehicles · built 24 Jun 2005 to 29 Jun 2006
• YARIS: 1,335 vehicles · built 7 Nov 2005 to 26 Jun 2009

The drivers and front passengers seat forward/rearward adjustment mechanism locking spring could fail under repeated operation of the mechanism. The seat may not lock into the adjusted position. If the vehicle is operated with a broken seat rail spring the seat could move in the event of a crash

Fix: Recall all affected vehicles and replace the spring.

10,317 vehicles · built 13 Jun 2005 to 12 May 2010

It is possible for condensation water droplets to form within the relay in the electric power steering control module. This can cause a short circuit across terminals within the relay. If this occurs and abnormally high voltage is detected by the control module it will shut down the power to the EPS which will coincide with a warning buzzer and light illuminating on the dash. This will result in the loss of power assistance to the steering.

Fix: Recall all affected vehicles and replace the power control module.

• YARIS: 5,409 vehicles · built 20 Jul 2011 to 23 Nov 2011
• YARIS: 5,409 vehicles · built 12 Sep 2011 to 24 Oct 2011
• YARIS: 5,409 vehicles · built 6 Sep 2011 to 2 Nov 2011
• YARIS: 5,409 vehicles · built 26 Jul 2011 to 16 Nov 2011
• YARIS: 5,409 vehicles · built 29 Jul 2011 to 16 Nov 2011
• YARIS: 5,409 vehicles · built 22 Jul 2011 to 18 Nov 2011
• YARIS: 5,409 vehicles · built 4 Oct 2011 to 25 Oct 2011
• YARIS: 5,409 vehicles · built 21 Jul 2011 to 21 Nov 2011
• YARIS: 5,409 vehicles · built 6 Oct 2011 to 27 Oct 2011
• YARIS: 5,409 vehicles · built 21 Jul 2011 to 21 Mar 2012
• YARIS: 5,409 vehicles · built 26 Jul 2011 to 23 Nov 2011
• YARIS: 5,409 vehicles · built 10 Nov 2010 to 5 Sep 2011

It is possible that a brake fluid leak could develop on brake pipe unions of either of the rear brake calipers or rear brake cylinders. If this occurs then the driver will receive a warning in the form of a warning light illuminating on the instrument panel. However if the driver does not heed this warning the braking efficiency of the vehicle could be impaired and the stopping distance increased.

Fix: Recall all affected vehicles to check re-tighten the unions and if required replace any damaged/defective components.

• YARIS: 1,504 vehicles · built 4 Apr 2013 to 26 Apr 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 19 Apr 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 17 May 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 2 Apr 2013
• YARIS: 1,504 vehicles · built 4 Apr 2013 to 22 Apr 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 23 May 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 22 Apr 2013
• YARIS: 1,504 vehicles · built 3 Apr 2013 to 17 May 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 25 Apr 2013
• YARIS: 1,504 vehicles · built 3 Apr 2013 to 4 Apr 2013
• YARIS: 1,504 vehicles · built 3 Apr 2013 to 18 Apr 2013
• YARIS: 1,504 vehicles · built 2 Apr 2013 to 18 Apr 2013
• YARIS: 1,504 vehicles · built 3 Apr 2013 to 12 May 2013

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Fix: Recall the vehicles that are likely to be affected to replace the airbag.

85,405 vehicles · built 8 Jan 2001 to 15 Nov 2003

It is possible moisture or other fluids may enter the drivers window and contaminate the main power window switch. If this occurs and the switch is damaged it could overheat and cause it to melt and/or smoke. If this situation is not identified it could result in a vehicle fire.

Fix: Recall all affected vehicles and check the switch. If the switch is not damaged a waterproof cover will be fitted. If the switch is damaged it will be replaced and a waterproof cover will be fitted.

• YARIS: 138,049 vehicles · built 1 Sep 2008 to 22 Dec 2008
• YARIS: 138,049 vehicles · built 1 Sep 2006 to 2 Dec 2008

Due to the improper installation of the left A-pillar trim there ia a possibility that the trim may become detached when the curtain shield airbag would deploy during a crash. If this happens the loose garnish could injure the LH seat occupant of the vehicle.

Fix: Inspection of the installation and repair if needed.

10,587 vehicles · built 12 Apr 2010 to 4 Jan 2011

The combustion rate of the airbag propellant may be too fast causing excessive internal pressure in the inflator during airbag deployment. In an extreme case the inflator casing may rupture leading to a scattering of metal fragments.

Fix: Recall the vehicles that are likely to be affected to replace the front passenger airbag assembly.

14 vehicles · built 29 May 2001 to 30 May 2001

It has been identified that on affected vehicles condensation resulting from cold-weather use of the heater or other causes may form on the worn surface of a component within the throttle pedal assembly known as the friction device. If this occurs there is a possibility that in the worst case the accelerator pedal may return slowly or does not return to the engine idle position.

Fix: Recalled vehicles will have a precision-cut steel reinforcing bar fitted into the accelerator pedal assembly which will create a space in order to reduce the surface tension between the friction device and a component referred to as the pedal arm. The subject bar also strengthens the reaction force of the spring that returns the accelerator pedal to it's non-pressed position.

174,426 vehicles · built 1 Nov 2005 to 30 Sep 2009

It has been identified that the possibility exists that the sound insulator beneath the front seatbelt pretensioner may become damaged by the high temperature gas generated when the device is activated during a collision. In the worst case should the insulator ignite a post-collision fire may ensue.

Fix: Recalled vehicles will have the sound insulator removed from beneath the centre body pillars.

• YARIS: 45,335 vehicles · built 13 Jun 2005 to 9 Apr 2007
• YARIS: 45,335 vehicles · built 7 Nov 2005 to 17 Apr 2007

It has been identified that the following seat defects may occur a Front and rear seats - the locking performance of the headrest may be insufficient during an impact and may cause ejection of the headrest from the seat back. b Front seats only- The reliability of the side airbag deployment on the front seats may be insufficient during an impact and may not offer the protection intended.

Fix: Recalled vehicles will have the following remedial actions performed:-a) The rear seat headrest guide springs and buttons will be replaced.b) The front seat headrest supports will be replaced. c) The front seat back pads and covers will be replaced.

19,075 vehicles · built 4 Nov 2005 to 31 Jul 2006

Due to improper moulding of the body of the crankshaft position sensor engine oil may penetrate the seal and enter the sensor wiring connector. In this condition the engine oil within the sensor's wiring connector may expand due to engine heat and could deform the sensor. In the worst case the connector may become disconnected which could cause the engine to stall while driving and restarting would not be possible.

Fix: Recalled vehicles will have the crankshaft position sensor replaced.

7,893 vehicles · built 31 Jan 2001 to 29 Oct 2001

In frequent stop/start conditions in snow and severely cold weather compacted snow/ice may build up on the inner face of the wheel disc. In extreme circumstances the snow/ice may strike and distort the metal pipe that connects to the rear brake cylinder. Impaired braking and a hydraulic fluid leak may result.

Fix: Fit a modified and re-routed brake pipe.

49,470 vehicles · built 10 Oct 2002 to 11 Mar 2002

There is a possibility that under certain conditions when applying the brakes hard and suddenly as in a panic situation a locking of the rear wheels may occur. The vehicle handling will then become unstable.

Fix: Recall affected vehicles and replace brake proportioning valve with a modified type.

19,639 vehicles · built 1 Jan 1999 to 31 Jan 2000