Aston Martin recalls

On affected vehicles in a combination of very specific conditions the seal within one of the brake master cylinders can deform. This can lead to brake fluid not being released back into the reservoir causing drag and leading to an increase in temperature increasing the risk of a localised fire.

Fix: The revised remedy parts are not yet available. Aston Martin will contact owners to schedule a time date and location for brake master cylinder replacement when parts are available.

6 vehicles · built 9 Dec 2022 to 16 Jun 2023

On affected vehicles in a combination of very specific conditions the seal within one of the brake master cylinders can deform. This can lead to brake fluid not being released back into the reservoir causing drag and leading to an increase in temperature increasing the risk of a localised fire.

Fix: The revised remedy parts are not yet available. Aston Martin will contact owners to schedule a time date and location for brake master cylinder replacement when parts are available.

2 vehicles · built 6 Apr 2023 to 12 Jul 2024

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

505 vehicles · built 26 Apr 2020 to 30 Oct 2021

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

161 vehicles · built 25 Nov 2021 to 6 May 2022

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

192 vehicles · built 9 May 2022 to 16 Nov 2022

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

246 vehicles · built 17 Nov 2022 to 25 Apr 2025

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

362 vehicles · built 28 Apr 2023 to 29 Jun 2024

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

428 vehicles · built 9 Jul 2024 to 12 Sep 2025

On affected vehicles a reduced diameter shank bolt can cause the pin for the torque reaction link to move within the joint causing excessive wear and potential early failure. In a worst-case scenario failure of the rear lower suspension arm can affect vehicle handling and braking with an increased risk of a crash.

Fix: Replace the rear torque reaction bolts and if necessary replace the rear lower suspension arms.

9 vehicles · built 5 Jun 2025 to 24 Jul 2025

On affected vehicles under specific conditions the brake vacuum pump may not generate vacuum reducing brake assistance. This may result in increased stopping distances and increase the risk of a crash.

Fix: Update ESP (Electronic Stability Program) with modified software.

98 vehicles · built 14 Aug 2024 to 26 Jun 2025

On affected vehicles under specific conditions the brake vacuum pump may not generate vacuum reducing brake assistance. This may result in increased stopping distances and increase the risk of a crash.

Fix: Update ESP (Electronic Stability Program) with modified software.

13 vehicles · built 7 Jan 2025 to 22 May 2025

On affected vehicles incorrect length screws may have been used to attach the rear fuse box closing panel which could cause damage to the wiring harness and in a worst-case scenario a risk of fire.

Fix: Replace rear fuse box closing panel screws and inspect and if necessary replace any damaged parts.

19 vehicles · built 16 Jun 2020 to 22 Sep 2024

On affected vehicles incorrect length screws may have been used to attach the rear fuse box closing panel which could cause damage to the wiring harness and in a worst-case scenario a risk of fire.

Fix: Replace rear fuse box closing panel screws and inspect and if necessary replace any damaged parts.

6 vehicles · built 29 Sep 2023 to 25 Oct 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

234 vehicles · built 30 Sep 2022 to 11 Mar 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

6 vehicles · built 19 Jun 2024 to 9 Jul 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

358 vehicles · built 16 Feb 2023 to 30 Jun 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

23 vehicles · built 13 Oct 2023 to 30 Jun 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

10 vehicles · built 30 Sep 2022 to 11 Mar 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

10 vehicles · built 19 Jun 2024 to 9 Jul 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

153 vehicles · built 16 Feb 2023 to 30 Jun 2024

On affected vehicles the oil hoses for the engine oil cooler may be prone to split with a resulting loss of oil and oil pressure.

Fix: On the affected vehicles the oil cooler hoses will be replaced

14 vehicles · built 13 Oct 2023 to 30 Jun 2024

On affected vehicles it is possible the fixings for the fuses are not correctly torqued

Fix: On affected vehicles check and replace fuse fixings as required

655 vehicles · built 16 Jul 2020 to 6 May 2022

On affected vehicles it is possible the fixings for the fuses are not correctly torqued

Fix: On affected vehicles check and replace fuse fixings as required

137 vehicles · built 5 May 2022 to 4 Sep 2022

On affected vehicles it is possible the fixings for the fuses are not correctly torqued

Fix: On affected vehicles check and replace fuse fixings as required

503 vehicles · built 27 Jan 2022 to 21 Sep 2023

On affected vehicles it is possible the fixings for the fuses are not correctly torqued

Fix: On affected vehicles check and replace fuse fixings as required

11 vehicles · built 28 Dec 2022 to 4 Sep 2023

On affected vehicles it is possible the fixings for the fuses are not correctly torqued

Fix: On affected vehicles check and replace fuse fixings as required

7 vehicles · built 14 Jul 2022 to 7 Sep 2023

On affected vehicles oil cooler hoses may be prone to leak resulting in loss of oil and oil pressure

Fix: On affected vehicles oil cooler hoses will be replaced

317 vehicles · built 28 Sep 2022 to 4 Jul 2023

On affected vehicles oil cooler hoses may be prone to leak resulting in loss of oil and oil pressure

Fix: On affected vehicles oil cooler hoses will be replaced

2 vehicles · built 6 Jun 2023 to 27 Jun 2023

Certain fixings on the front seat airbag may not have been �tightened� to the correct torque.

Fix: Examine the front seat airbag fixings and if necessary secure the fixings.

20 vehicles · built 17 Aug 2016 to 8 May 2019

Certain fixings on the front seat airbag may not have been �tightened� to the correct torque.

Fix: Examine the front seat airbag fixings and if necessary secure the fixings.

20 vehicles · built 17 Aug 2016 to 8 May 2019

Certain fixings on the front seat airbag may not have been �tightened� to the correct torque.

Fix: Examine the front seat airbag fixings and if necessary secure the fixings.

20 vehicles · built 17 Aug 2016 to 8 May 2019

Vehicles may not have had their passenger airbag fixings �tightened� to the correct torque specification

Fix: Examine the passenger airbag fixings and if necessary secure the fixings.

15 vehicles · built 6 Nov 2017 to 18 Feb 2019

Vehicles may not have had their passenger airbag fixings �tightened� to the correct torque specification

Fix: Examine the passenger airbag fixings and if necessary secure the fixings.

15 vehicles · built 6 Nov 2017 to 18 Feb 2019

Vehicles may not have had their passenger airbag fixings �tightened� to the correct torque specification

Fix: Examine the passenger airbag fixings and if necessary secure the fixings.

15 vehicles · built 6 Nov 2017 to 18 Feb 2019

When combined with a damaged steering column control module clock spring and insufficient grounding of the steering column an electrostatic discharge may lead to an inadvertent deployment of the driver's airbag. Drivers will be alerted to a potential fault by the airbag warning in the instrument cluster and an additional warning message.

Fix: On affected vehicles install a contact bridge and a contact spring that will provide a suitable ground for the steering column.

1,069 vehicles · built 16 Nov 2015 to 30 Oct 2017

Due to a communication error between the Engine Control Module (ECM) software and the Transmission Control Module (TCM) the transmission park pawl may not engage. In certain circumstances such as when the park brake is not applied the vehicle may roll away.

Fix: On affected vehicles update the software for the Transmission Control Module.

3,849 vehicles · built 18 Dec 2007 to 11 Jan 2017

Due to a communication error between the Engine Control Module (ECM) software and the Transmission Control Module (TCM) the transmission park pawl may not engage. In certain circumstances such as when the park brake is not applied the vehicle may roll away.

Fix: On affected vehicles update the software for the Transmission Control Module.

3,849 vehicles · built 18 Dec 2007 to 11 Jan 2017

In some circumstances when the right side front seat is operated to its fully reward position the seat runner can compress the battery supply cable and cause the seat to damage the battery supply cable. This may cause an open circuit and/or ground the supply cable which may then overheat.

Fix: On affected vehicles examine the battery supply cable for damage and install a routing block to ensure that the seat runner cannot compress the battery supply cable. If necessary replace the cable.

6,542 vehicles · built 19 Dec 2003 to 17 Nov 2015

Due to a communication error between the Engine Control Module (ECM) software and the Transmission Control Module (TCM) the transmission park pawl may not engage. In certain circumstances such as when the park brake is not applied the vehicle may roll away.

Fix: On affected vehicles update the software for the Transmission Control Module.

3,849 vehicles · built 18 Dec 2007 to 11 Jan 2017

Due to a communication error between the Engine Control Module (ECM) software and the Transmission Control Module (TCM) the transmission park pawl may not engage. In certain circumstances such as when the park brake is not applied the vehicle may roll away.

Fix: On affected vehicles update the software for the Transmission Control Module.

3,849 vehicles · built 18 Dec 2007 to 11 Jan 2017

In some circumstances when the right side front seat is operated to its fully reward position the seat runner can compress the battery supply cable and cause the seat to damage the battery supply cable. This may cause an open circuit and/or ground the supply cable which may then overheat.

Fix: On affected vehicles examine the battery supply cable for damage and install a routing block to ensure that the seat runner cannot compress the battery supply cable. If necessary replace the cable.

6,542 vehicles · built 19 Dec 2003 to 17 Nov 2015

In some circumstances when the right side front seat is operated to its fully reward position the seat runner can compress the battery supply cable and cause the seat to damage the battery supply cable. This may cause an open circuit and/or ground the supply cable which may then overheat.

Fix: On affected vehicles examine the battery supply cable for damage and install a routing block to ensure that the seat runner cannot compress the battery supply cable. If necessary replace the cable.

6,542 vehicles · built 19 Dec 2003 to 17 Nov 2015

In some circumstances when the right side front seat is operated to its fully reward position the seat runner can compress the battery supply cable and cause the seat to damage the battery supply cable. This may cause an open circuit and/or ground the supply cable which may then overheat.

Fix: On affected vehicles examine the battery supply cable for damage and install a routing block to ensure that the seat runner cannot compress the battery supply cable. If necessary replace the cable.

6,542 vehicles · built 19 Dec 2003 to 17 Nov 2015

Due to a communication error between the Engine Control Module (ECM) software and the Transmission Control Module (TCM) the transmission park pawl may not engage. In certain circumstances such as when the park brake is not applied the vehicle may roll away.

Fix: On affected vehicles update the software for the Transmission Control Module.

3,849 vehicles · built 18 Dec 2007 to 11 Jan 2017

The Tyre Pressure Monitoring System (TPMS) on the affected vehicles was calibrated incorrectly and as a result does not illuminate the low tyre pressure warning tell-tale at the required minimum activation pressure.

Fix: Recalibrate the TPMS on affected vehicles.

628 vehicles · built 28 Nov 2016 to 12 Jun 2017

A hydraulic connector may fail and cause a transmission oil leak. This may have an adverse effect on gear selection.

Fix: Add a support bracket which will be installed to hold the pipe securely in position and prevent movement of the assembly.

10 vehicles · built 19 Sep 2011 to 26 Oct 2011

A hydraulic connector may fail and cause a transmission oil leak. This may have an adverse effect on gear selection.

Fix: On affected vehicles replace the clutch pipe connector assembly related brackets and parts

165 vehicles · built 23 Jul 2010 to 23 Sep 2013

As part of a software update the stored adjustment settings for the automatic clutch were not deleted and re-taught. These stored settings are incompatible with the updated software and can result in incorrect operation in certain circumstances. This may adversely affect gear changes including uncommanded selection of neutral. If neutral is selected manual gear selection will be available.

Fix: On affected vehicles the clutch software will be re-installed and the system re-taught.

290 vehicles · built 23 Jul 2010 to 15 Aug 2012

On affected vehicles the right fron seat can compress the battery supply cable. Prolonged occurences coulld cause damage to the insulation and the cable may short out

Fix: Fit new cable guide to reroute supply cable. Check condition of supply cable and where necessary reinforce insulation . In rare instances the cable may require replacement.

691 vehicles · built 8 Mar 2007 to 17 May 2007

On affected vehicles the right fron seat can compress the battery supply cable. Prolonged occurences coulld cause damage to the insulation and the cable may short out

Fix: Fit new cable guide to reroute supply cable. Check condition of supply cable and where necessary reinforce insulation . In rare instances the cable may require replacement.

691 vehicles · built 10 Jul 2007 to 27 Jan 2011

On affected vehicles the right fron seat can compress the battery supply cable. Prolonged occurences coulld cause damage to the insulation and the cable may short out

Fix: Fit new cable guide to reroute supply cable. Check condition of supply cable and where necessary reinforce insulation . In rare instances the cable may require replacement.

691 vehicles · built 3 Sep 2012 to 14 Nov 2015

On affected vehicles the right fron seat can compress the battery supply cable. Prolonged occurences coulld cause damage to the insulation and the cable may short out

Fix: Fit new cable guide to reroute supply cable. Check condition of supply cable and where necessary reinforce insulation . In rare instances the cable may require replacement.

691 vehicles · built 19 Jan 2011 to 31 Jan 2011

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles The control module for the front heated seats mail fail and when the ignition is switched on allow a permanent feed to the heater element(s). In this condition it may not be possible to switch off the heater element and over a period of time this may cause a seat to overheat and smouldering to occur. Occupants will notice an inability to switch the seat heater off using the designated switch and over longer periods a higher than normal temperature of the seat squab.

Fix: Fit additional seat heater monitoring modules. Where necessary seat elements may also be replaced.

8,299 vehicles · built 15 Jun 2006 to 6 Nov 2014

On affected vehicles the transmission switches have a chrome plating surround. This can interact with the printed circuit board within the switches and create an intermittent earth path to other surrounding parts In the subject vehicles this can cause the transmission to default to neutral without any driver input for gear selection resulting in a loss drive.

Fix: Replace existing switches with updated version. Brakes and steering are not affected.

313 vehicles

On affected vehicles the transmission switches have a chrome plating surround. This can interact with the printed circuit board within the switches and create an intermittent earth path to other surrounding parts In the subject vehicles this can cause the transmission to default to neutral without any driver input for gear selection resulting in a loss drive.

Fix: Replace existing switches with updated version. Brakes and steering are not affected.

313 vehicles

The throttle pedal may fail resulting in the driver being unable to accelerate or maintain speed. The throttle pedal arm on the affected vehicles is not to specification.

Fix: Recall the vehicles that are likely to be affected to replace the throttle pedal with one of the correct specification.

1,289 vehicles · built 14 May 2012 to 10 Apr 2013

It has been established that the Tyre Pressure Management System (TPMS) ECU had been installed with incorrect specification software for the front axle. The software allows for a greater tyre pressure difference between tyres on the front axle. If this occurs it could in extreme circumstances affect the stability and directional control of the vehicle.

Fix: Recall all affected vehicles and install the correct software.

307 vehicles · built 1 Apr 2009 to 30 Sep 2012

It has been established that the front suspension bottom suspension arm cam-bolt may be out of specification. It is possible that these bolts could crack and fail. This could in extreme cases affect the directional control of the vehicle.

Fix: Recall all affected vehicles for the replacement of the cam-bolt.

1,035 vehicles · built 1 Mar 2007 to 30 Sep 2007

It has been established that the front suspension bottom suspension arm cam-bolt may be out of specification. It is possible that these bolts could crack and fail. This could in extreme cases affect the directional control of the vehicle.

Fix: Recall all affected vehicles for the replacement of the cam-bolt.

1,035 vehicles · built 1 Mar 2007 to 30 Sep 2007

It has been established that the front suspension bottom suspension arm cam-bolt may be out of specification. It is possible that these bolts could crack and fail. This could in extreme cases affect the directional control of the vehicle.

Fix: Recall all affected vehicles for the replacement of the cam-bolt.

1,035 vehicles · built 1 Mar 2007 to 30 Sep 2007

It has been identified that during the build process of the subject vehicles a safety critical action to check the torque of the front sub frame assembly bolts was omitted. Should the situation be ignored the driver would become aware of an unusual steering response.

Fix: Recalled vehicles will have the subject bolts inspected to ascertain whether they have been paint marked to indicate that the torque has been checked during production. Should this not be the case the bolts will be re-torqued.

18 vehicles · built 6 Apr 2009 to 22 Jul 2009

It has been identified that during the build process of the subject vehicles a safety critical action to check the torque of the front sub frame assembly bolts was omitted. Should the situation be ignored the driver would become aware of an unusual steering response.

Fix: Recalled vehicles will have the subject bolts inspected to ascertain whether they have been paint marked to indicate that the torque has been checked during production. Should this not be the case the bolts will be re-torqued.

18 vehicles · built 6 Apr 2009 to 22 Jul 2009

It has been identified that during the build process of the subject vehicles a safety critical action to check the torque of the front sub frame assembly bolts was omitted. Should the situation be ignored the driver would become aware of an unusual steering response.

Fix: Recalled vehicles will have the subject bolts inspected to ascertain whether they have been paint marked to indicate that the torque has been checked during production. Should this not be the case the bolts will be re-torqued.

18 vehicles · built 6 Apr 2009 to 22 Jul 2009

The engine may not start because the power train to chassis primary earth stud may have intermittent high resistance. This condition may occur when electrical items that draw high current are utilised in which case the electrical path could route through the rear braided hoses causing them to heat up and possibly melt leading to a soft pedalillumination of the brake warning lamp and poor starting.

Fix: Recall the vehicles that are likely to be affected so the primary earth stud can be moved to a new location and fit a secondary earth strap between the transmission and chassis.

125 vehicles · built 23 May 2005 to 27 Oct 2005

Some vehicles may have been manufactured with an automatic transmission parking brake component which may not have been hardened to the correct specification. This could result in the transmission parking brake not engaging when park on the transmission is selected.

Fix: Recalled vehicles will have the parking brake pawl guide plate replaced with a quality assured item.

3 vehicles

It has been identified that a number of vehicles have been assembled with two in-line rear brake pressure reducing valves installed to one of the rear brake lines instead of one valve in each rear brake line. This condition can cause the vehicle to pull slightly to one side under heavy braking efficiency however is maintained as the system is regulated by the ABS.

Fix: Recall likely to be affected vehicles and modify to one brake pressure reducing valve to each rear brake line.

59 vehicles

The electronic throttle pedal assembly cross shaft can become displaced from its housing following involuntary displacement of an ultrasonically domed head (LHS end). This is designed to keep the cross shaft in place along with a secondary retaining cross pin at the opposite side of the housing. With the cross shaft displaced throttle control is lost. If ignored a failed cross shaft would lead to loss of throttle control whilst driving.

Fix: Likely to be affected vehicles will be recalled at which time the throttle assembly will be checked for compliance with specification. Should a non-compliance be identified the throttle pedal assembly will be replaced.

473 vehicles · built 10 Nov 2001 to 9 Nov 2004

Power assisted steering high pressure flexible hose may contact the left hand exhaust manifold and burn through leading to a progressive loss of hydraulic fluid and power assistance.

Fix: Check the position of the high pressure hose in relation to the exhaust manifold. If the hose is touching the manifold or there is insufficient air gap fit a new high pressure hose and reposition and clip as specified.

62 vehicles · built 1 May 1999 to 31 Mar 2003

The steering column lighting switchgear wires can potentially become trapped leading to partial loss of lighting functionality during operation.

Fix: Recall affected vehicles and fit a quality assured steering column switchgear assembly

1,609 vehicles · built 1 Apr 1996 to 28 Feb 2001

The steering column lighting switchgear wires can potentially become trapped leading to partial loss of lighting functionality during operation.

Fix: Recall affected vehicles and fit a quality assured steering column switchgear assembly

1,609 vehicles · built 1 Apr 1996 to 28 Feb 2001

A fault in the ignition software may result in misfiring and power loss on one bank of cylinders. This situation could also cause overheating of the exhaust catalyst.

Fix: Affected Vehicles are being recalled for replacement of the power train control module.(PCM)

481 vehicles · built 1 Jun 1999 to 30 Sep 2000

A fault in the ignition software may result in misfiring and power loss on one bank of cylinders. This situation could also cause overheating of the exhaust catalyst.

Fix: Affected Vehicles are being recalled for replacement of the power train control module.(PCM)

481 vehicles · built 1 Jun 1999 to 30 Sep 2000

A fault in the ignition software may result in misfiring and power loss on one bank of cylinders. This situation could also cause overheating of the exhaust catalyst.

Fix: Affected Vehicles are being recalled for replacement of the power train control module.(PCM)

481 vehicles · built 1 Jun 1999 to 30 Sep 2000

One of the three variants of de Dion rear axle tube assemblies may suffer from stress cracks between the rear hub to axle tube interface following extended use. This could result in impeded rear road wheel stability should failure occur.

Fix: Recall affected vehicles to check and/or replace rear axle.

110 vehicles · built 1 Jan 1994 to 31 Dec 1996

There is a possibility that stress cracking of the steering rack mounting brackets may occur which could impede steering action.

Fix: Recall affected vehicles and replace brackets with modified type.

204 vehicles · built 1 Jan 1993 to 31 Dec 1999

There is a possibility that stress cracking of the steering rack mounting brackets may occur which could impede steering action.

Fix: Recall affected vehicles and replace brackets with modified type.

204 vehicles · built 1 Jan 1993 to 31 Dec 1999

There is a possibility that stress cracking of the steering rack mounting brackets may occur which could impede steering action.

Fix: Recall affected vehicles and replace brackets with modified type.

204 vehicles · built 1 Jan 1993 to 31 Dec 1999

There is a possibility that the front damper lower mounting bracket may detach due to insufficient welding and displaced damper may restrict steering action.

Fix: Recall affected vehicles and check that damper mounting bracket is butt welded on all three sides. If not replace bracket.

358 vehicles · built 1 Jun 1999 to 30 Nov 1999

There is a possibility that the front damper lower mounting bracket may detach due to insufficient welding and displaced damper may restrict steering action.

Fix: Recall affected vehicles and check that damper mounting bracket is butt welded on all three sides. If not replace bracket.

358 vehicles · built 1 Jun 1999 to 30 Nov 1999

There is a possibility that the front damper lower mounting bracket may detach due to insufficient welding and displaced damper may restrict steering action.

Fix: Recall affected vehicles and check that damper mounting bracket is butt welded on all three sides. If not replace bracket.

358 vehicles · built 1 Jun 1999 to 30 Nov 1999

The seat belt B pillar anchorage may disengage from it's index plate during a frontal impact.

Fix: Potentially affected vehicles are being recalled to have the marking on the index plate inspected. Where the marking indicates that the plate is not the correct type it will be replaced with a quality assured example.

43 vehicles · built 1 Feb 1997 to 30 Nov 1997

The seat belt B pillar anchorage may disengage from it's index plate during a frontal impact.

Fix: Potentially affected vehicles are being recalled to have the marking on the index plate inspected. Where the marking indicates that the plate is not the correct type it will be replaced with a quality assured example.

43 vehicles · built 1 Feb 1997 to 30 Nov 1997

Should the low brake fluid warning lamp bulb fail the bulb check facility is not enabled to check this condition.

Fix: The affected vehicles are being recalled by the manufacturer for a minor wiring modification to the circuit concerned.

139 vehicles · built 1 Apr 1996 to 30 Nov 1996

Should the low brake fluid warning lamp bulb fail the bulb check facility is not enabled to check this condition.

Fix: The affected vehicles are being recalled by the manufacturer for a minor wiring modification to the circuit concerned.

139 vehicles · built 1 Apr 1996 to 30 Nov 1996