Maserati recalls

On affected vehicles the manufacturer’s plate may detach.

Fix: On affected vehicles the manufacturer’s plate will be replaced following a rework of the area which the plate is attached to.

5 vehicles · built 30 Jan 2024 to 8 May 2024

On affected vehicles the pressure/temperature sensor within the short fuel line may cause a possible fuel leakage in engine bay. This may lead to a loss of power and in the worst case a potential fire.

Fix: Replacement of the short fuel line containing the pressure sensor.

1 vehicles · built 25 Jun 2021 to 25 Jun 2021

On affected vehicles the pressure/temperature sensor within the short fuel line may cause a possible fuel leakage in engine bay. This may lead to a loss of power and in the worst case a potential fire.

Fix: Replacement of the short fuel line containing the pressure sensor.

6 vehicles · built 30 Apr 2021 to 24 Aug 2021

On affected vehicles there may be an issue involving the retaining stud in the area of the front windscreen frame.

Fix: A check of the positioning of the retaining pin and application of the sealant.

30 vehicles · built 30 Sep 2022 to 23 Jun 2023

Possible insufficient tightening on electrical connections of 48 volt power system.

Fix: Gain access to the battery system and check tightness of connections to the 48 volt power system. resecure if required.

6 vehicles · built 21 Jul 2021 to 26 Mar 2022

Possible gearbox electrical cable contact with Catalyst thermal shield.

Fix: Check and ensure the correct positioning of the gearbox wiring harness in relation to the catalytic convertor shield if required replace the wiring harness.

1 vehicles · built 14 Apr 2022 to 19 Apr 2022

Supply cables for the 48Volt battery system have an incorrect tightening torque.

Fix: Inspect and retighten cable fixing screws for the 48Volt battery system.

122 vehicles · built 24 Aug 2021 to 24 Sep 2021

When the tail-lamp is receiving a voltage close to the maximum (16V) the tail-lamp may start flickering.

Fix: Check the production date of the tail-lamps if the fitted lamps are within the defective range replacement of the rear lamp/lamps will be required.

20 vehicles · built 24 Jan 2022 to 24 Jan 2022

Wrong TVV (Type-Variant-Version) on statutory plate.

Fix: Replace label located on B Pillar

37 vehicles · built 28 Sep 2021 to 30 Sep 2021

Wrong TVV (Type-Variant-Version) on statutory plate.

Fix: Replace label located on B Pillar

37 vehicles · built 28 Sep 2021 to 30 Sep 2021

A deviation of the P/T sensor moulding process of the plastic housing. Possible Fuel Leakage in engine bay Loss of power potential fire risk in worst case.

Fix: Replacement of the short fuel line containing the pressure sensor.

58 vehicles · built 28 Jan 2021 to 27 Oct 2021

Exhaust active valve cable may short circuit due to contact with the exhaust system.

Fix: Check cable layout reposition and repair if necessary.

56 vehicles · built 24 Aug 2021 to 16 Sep 2021

Incorrect automatic tightening of an electrical cable on production.

Fix: Check and retighten the connection.

3 vehicles · built 13 Jul 2021 to 22 Sep 2021

The Electronic Power Steering function may not be available.

Fix: Replacement of steering rack.

11 vehicles · built 9 Apr 2021 to 9 Apr 2021

Front tyres outer tread may have been damaged.

Fix: Check and replace tyre if required

7 vehicles · built 23 Mar 2021 to 29 Mar 2021

Engine code marked on Diesel engine replaced in aftersales is different from the homologated and Production code

Fix: Documentation will be provided to the customer stating the Italian transport authority confirm this marking is an administration error.

2 vehicles · built 9 Jan 2019 to 3 Feb 2019

Engine code marked on Diesel engine replaced in aftersales is different from the homologated and Production code

Fix: Documentation will be provided to the customer stating the Italian transport authority confirm this marking is an administration error.

2 vehicles · built 9 Jan 2019 to 3 Feb 2019

Incorrect sticker shows data M1561F4 5W correct version is M1561F 4APD.

Fix: Replacement of the sticker label.

1 vehicles · built 9 Jan 2019 to 3 Feb 2019

Front headlamps full LED version headlamp vertical beam out of compliance.

Fix: Check and adjustment of the front headlamp vertical beam.

320 vehicles · built 11 Aug 2017 to 21 Feb 2019

Front headlamps full LED version headlamp vertical beam out of compliance.

Fix: Check and adjustment of the front headlamp vertical beam.

320 vehicles · built 11 Aug 2017 to 21 Feb 2019

Internal malfunction of the air bag control unit

Fix: Replacement of the air bag control unit

84 vehicles · built 5 Nov 2014 to 29 Apr 2019

Internal malfunction of the air bag control unit

Fix: Replacement of the air bag control unit

84 vehicles · built 5 Nov 2014 to 29 Apr 2019

Blind spot detection system has been marked with the wrong ECE certification labelling.

Fix: Attaching the correct label to the left and right rear blind spot sensors and within the owners quick reference guide.

11 vehicles · built 10 Oct 2018 to 12 Oct 2018

There is a possibility that a leak may occur in the fuel line.

Fix: Replacement of the fuel delivery line.

126 vehicles · built 29 Aug 2017 to 4 Dec 2017

There is a possibility that a leak may occur in the fuel line.

Fix: Replacement of the fuel delivery line.

126 vehicles · built 29 Aug 2017 to 4 Dec 2017

Possible incorrect welding due to human error of the 4 sections of the front engine under frame. This has been caused by an interruption in the welding process Possible brake of the welds Sub-frame can lost the correct alignment and the vehicle could lose the stability

Fix: Inspection of the welded points if welding Is defective replacement of the front sub-frame required

1 vehicles · built 4 Dec 2017 to 4 Dec 2017

The resistor for the low pressure fuel pump may fail which can cause loss of power and eventually the engine to shut down.

Fix: Recall the vehicles that are likely to be affected and replace the low pressure fuel pump resistor.

26 vehicles · built 31 Oct 2014 to 28 Jun 2017

Due to material imperfections the fuel delivery line may leak at line unions. This is more likely after prolonged use.

Fix: On affected vehicles replace the fuel delivery line.

53 vehicles · built 29 Aug 2017 to 4 Dec 2017

Due to material imperfections the fuel delivery line may leak at line unions. This is more likely after prolonged use.

Fix: On affected vehicles replace the fuel delivery line.

53 vehicles · built 29 Aug 2017 to 4 Dec 2017

The short hose on the pipe between the turbocharger and the intercoolers could break during the normal use of the vehicle. This could result in loss of performance and cause the check engine light to illuminate as the hose material may not conform to manufacturers specification.

Fix: Replace the short hose on the pipe between the turbocharger and the intercoolers. In some cases the replacement of the entire intercooler pipe will be necessary; this will be determined by the VIN number.

125 vehicles · built 19 Sep 2016 to 2 Jan 2017

Some vehicles may have been manufactured with an incorrect driver seat wiring harness layout which can cause the seat wiring harness to rub against metal points on the seat/seat frame assembly through normal seat adjustment operation. Over time this can lead to an inoperative seat adjustment system and in rare cases a potential risk of fire due to an electrical short to ground between the seat wiring harness and the seat adjustment motor assembly.

Fix: Replace 2 seat circuit breakers with 25 amp mini-fuses check harness apply protective barrier and reposition if undamaged. If damaged replace harness and then ensure repositioned and protective barrier applied.

3,844 vehicles · built 7 Feb 2013 to 24 Nov 2016

Some vehicles may have been manufactured with an incorrect driver seat wiring harness layout which can cause the seat wiring harness to rub against metal points on the seat/seat frame assembly through normal seat adjustment operation. Over time this can lead to an inoperative seat adjustment system and in rare cases a potential risk of fire due to an electrical short to ground between the seat wiring harness and the seat adjustment motor assembly.

Fix: Replace 2 seat circuit breakers with 25 amp mini-fuses check harness apply protective barrier and reposition if undamaged. If damaged replace harness and then ensure repositioned and protective barrier applied.

3,844 vehicles · built 7 Feb 2013 to 24 Nov 2016

Some vehicles may have been manufactured with an incorrect driver seat wiring harness layout which can cause the seat wiring harness to rub against metal points on the seat/seat frame assembly through normal seat adjustment operation. Over time this can lead to an inoperative seat adjustment system and in rare cases a potential risk of fire due to an electrical short to ground between the seat wiring harness and the seat adjustment motor assembly.

Fix: Replace 2 seat circuit breakers with 25 amp mini-fuses check harness apply protective barrier and reposition if undamaged. If damaged replace harness and then ensure repositioned and protective barrier applied.

3,844 vehicles · built 7 Feb 2013 to 24 Nov 2016

There is a possibility that a leak may occur in the fuel delivery line. Prolonged use of the car could result in the possibility of a fuel leak at the engine end of the pipe where the quick release connector is fitted.

Fix: Recall the vehicles that are likely to be affected and replace the complete fuel delivery line.

283 vehicles · built 27 Jul 2013 to 31 Oct 2014

There is a possibility that a leak may occur in the fuel delivery line. Prolonged use of the car could result in the possibility of a fuel leak at the engine end of the pipe where the quick release connector is fitted.

Fix: Recall the vehicles that are likely to be affected and replace the complete fuel delivery line.

283 vehicles · built 27 Jul 2013 to 31 Oct 2014

It has been identified that the gearshift lever resting position may mislead drivers into believing the vehicle's transmission is in the park position when actually the it is still in a drive gear. This could result in the vehicle moving off without the driver being in the vehicle.

Fix: Recall all affected vehicles to replace the driver's door lock and update the software to introduce a drive away inhibition strategy.

1,039 vehicles · built 25 Nov 2013 to 9 Jul 2014

It has been identified that the gearshift lever resting position may mislead drivers into believing the vehicle's transmission is in the park position when actually the it is still in a drive gear. This could result in the vehicle moving off without the driver being in the vehicle.

Fix: Recall all affected vehicles to replace the driver's door lock and update the software to introduce a drive away inhibition strategy.

1,039 vehicles · built 25 Nov 2013 to 9 Jul 2014

It has been identified that the locking nut of the differential pinion may not have been tightened to the correct specification. This will be identified to the driver by noise generated from the differential and also possible vibration. If these warning signs are ignored and with prolonged use in this condition then it could result in a possible failure/locking of the differential and the subsequent loss of control of the vehicle.

Fix: Recall all affected vehicle to check the tightness of the locking nut on the differential pinion. If it is found to be incorrect then the differential will be replaced and possibly the drive-shaft if projections or metal contaminates are found in the differential rear cover.

30 vehicles · built 26 Sep 2016 to 30 Sep 2016

It has been identified that the locking nut of the differential pinion may not have been tightened to the correct specification. This will be identified to the driver by noise generated from the differential and also possible vibration. If these warning signs are ignored and with prolonged use in this condition then it could result in a possible failure/locking of the differential and the subsequent loss of control of the vehicle.

Fix: Recall all affected vehicle to check the tightness of the locking nut on the differential pinion. If it is found to be incorrect then the differential will be replaced and possibly the drive-shaft if projections or metal contaminates are found in the differential rear cover.

30 vehicles · built 26 Sep 2016 to 30 Sep 2016

Due to a manufacturing issue the front wheel bearing can become noisy and vibrate. If the driver does not take notice of these warnings then the bearing could fail and cause loss of control of the vehicle.

Fix: Recall all affected vehicles to check and if required replace the front wheel bearing.

5 vehicles · built 13 Apr 2015 to 24 Apr 2015

Due to a manufacturing issue the front wheel bearing can become noisy and vibrate. If the driver does not take notice of these warnings then the bearing could fail and cause loss of control of the vehicle.

Fix: Recall all affected vehicles to check and if required replace the front wheel bearing.

5 vehicles · built 13 Apr 2015 to 24 Apr 2015

In extreme and hard driving conditions it is possible for the rear tie rod fixing bolt to become loose which can ultimately result in loss of vehicle control.

Fix: Recall the vehicles that are likely to be affected and replace both rear toe in tie rod bolts and washers fixing points will be inspected and rear hub assembly replaced if unserviceable.

2,453 vehicles · built 21 Dec 2013 to 23 Sep 2015

In extreme and hard driving conditions it is possible for the rear tie rod fixing bolt to become loose which can ultimately result in loss of vehicle control.

Fix: Recall the vehicles that are likely to be affected and replace both rear toe in tie rod bolts and washers fixing points will be inspected and rear hub assembly replaced if unserviceable.

2,453 vehicles · built 21 Dec 2013 to 23 Sep 2015

Throttle pedal may jam in any position. This can lead to a heightened risk of a collision.

Fix: Recall the vehicles that are likely to be affected and replace the throttle pedal cover carpet mats carpet mat fixings modify floor covering depending on VIN list and inspection.

2,773 vehicles · built 25 Apr 2013 to 17 Dec 2015

Throttle pedal may jam in any position. This can lead to a heightened risk of a collision.

Fix: Recall the vehicles that are likely to be affected and replace the throttle pedal cover carpet mats carpet mat fixings modify floor covering depending on VIN list and inspection.

2,773 vehicles · built 25 Apr 2013 to 17 Dec 2015

Insufficient heat treatment may have been applied to the ratchet in the right hand door latch mechanism which may cause the Right Hand door to open inadvertently during driving and/or in an accident.

Fix: Recall the vehicles that are likely to be affected and replace the right hand door latch assembly.

12 vehicles · built 7 Jul 2015 to 26 Aug 2015

Insufficient heat treatment may have been applied to the ratchet in the right hand door latch mechanism which may cause the Right Hand door to open inadvertently during driving and/or in an accident.

Fix: Recall the vehicles that are likely to be affected and replace the right hand door latch assembly.

12 vehicles · built 7 Jul 2015 to 26 Aug 2015

Due to incorrect installation the power lead from the alternator to the starter motor may become damaged. This may cause the engine to stall and in extreme cases cause a fire in the engine compartment.

Fix: On affected vehicles replace the alternator to starter motor loom.

13 vehicles · built 15 Mar 2013 to 8 Jan 2015

The protection on the treaded portion of the tie-rod may not be to the manufacturer's specification. If the owner continues to use the vehicle in this condition it can result in damage occurring on the threaded portion of the tie-rod and may cause loss of control of the vehicle.

Fix: Recall all the affected vehicles and replace both tie-rods with quality assured items.

1,603 vehicles · built 25 Feb 2004 to 2 Sep 2008

The protection on the treaded portion of the tie-rod may not be to the manufacturer's specification. If the owner continues to use the vehicle in this condition it can result in damage occurring on the threaded portion of the tie-rod and may cause loss of control of the vehicle.

Fix: Recall all the affected vehicles and replace both tie-rods with quality assured items.

1,603 vehicles · built 25 Feb 2004 to 2 Sep 2008

It is possible that due to an internal issue within the ECU of the Tyre Pressure Management System (TPMS) an incorrect warning to the driver could appear on the instrument panel even when there is not an issue with the tyre pressures on the vehicle. This could cause the driver to panic and take avoiding action when it is not required. In extreme circumstances this could cause a safety risk to the occupants of the vehicle.

Fix: Recall affected vehicles to check the ECU. If found to be one of the affected components it will be replaced with a new unit.

12 vehicles · built 29 Nov 2011 to 13 Dec 2011

It is possible that due to an internal issue within the ECU of the Tyre Pressure Management System (TPMS) an incorrect warning to the driver could appear on the instrument panel even when there is not an issue with the tyre pressures on the vehicle. This could cause the driver to panic and take avoiding action when it is not required. In extreme circumstances this could cause a safety risk to the occupants of the vehicle.

Fix: Recall affected vehicles to check the ECU. If found to be one of the affected components it will be replaced with a new unit.

12 vehicles · built 29 Nov 2011 to 13 Dec 2011

It is possible that due to an internal issue within the ECU of the Tyre Pressure Management System (TPMS) an incorrect warning to the driver could appear on the instrument panel even when there is not an issue with the tyre pressures on the vehicle. This could cause the driver to panic and take avoiding action when it is not required. In extreme circumstances this could cause a safety risk to the occupants of the vehicle.

Fix: Recall affected vehicles to check the ECU. If found to be one of the affected components it will be replaced with a new unit.

12 vehicles · built 29 Nov 2011 to 13 Dec 2011

The seat belt warning lamp could illuminate even if the seat belts are correctly fastened causing distraction to the driver.

Fix: Recall the vehicles that are likely to be affected to replace both the front seat belt buckle branches.

4 vehicles

Due to a non-conformance with the outer tail light assembly it is possible the rear brake and/or the brake light may not operate. If this happens other drivers will be unaware the vehicle is intending to turn or stop and the rear lights will not be illuminated at night.

Fix: Affected vehicles will be recalled to have the tail light assembly checked. Where necessary the outer tail light will be replaced.

525 vehicles · built 17 Jun 2008 to 5 Mar 2010

Due to a non-conformance with the outer tail light assembly it is possible the rear brake and/or the brake light may not operate. If this happens other drivers will be unaware the vehicle is intending to turn or stop and the rear lights will not be illuminated at night.

Fix: Affected vehicles will be recalled to have the tail light assembly checked. Where necessary the outer tail light will be replaced.

525 vehicles · built 17 Jun 2008 to 5 Mar 2010

internal breakage inside the gearbox may cause the rear wheels to lock up.

Fix: Replace gearbox

15 vehicles · built 27 Sep 2010 to 29 Oct 2011

The rear tie-rods may not confirm to the correct manufacturing specification. Therefore depending on its usage and the road conditions it is possible that the tie-rod may become damaged and may fail which will result in the loss of control of the vehicle.

Fix: Recall the affected vehicles and replace the tie-rods.

131 vehicles

It has been identified that due to the installation of incorrect software the seatbelt warning buzzer may not sound when the seatbelts are not engaged.

Fix: Recalled vehicles will have the current software upgraded.

282 vehicles · built 1 Aug 2008 to 28 Feb 2009

It has been identified that due to the installation of incorrect software the seatbelt warning buzzer may not sound when the seatbelts are not engaged.

Fix: Recalled vehicles will have the current software upgraded.

282 vehicles · built 1 Aug 2008 to 28 Feb 2009

It has been identified that during manufacture an incorrect tightening torque may have been applied to the front suspension ball joint retaining nuts. This can result in the ball joint becoming loose in it's taper and in extreme circumstances an increase in wear may cause the suspension arm to break.

Fix: Recalled vehicles will have the subject ball joint retaining nuts checked for correct torque. Should this not be the case both suspension levers and the hub carrier will be changed.

1,577 vehicles · built 1 Sep 2003 to 30 Jun 2008

It has been identified that during manufacture an incorrect tightening torque may have been applied to the front suspension ball joint retaining nuts. This can result in the ball joint becoming loose in it's taper and in extreme circumstances an increase in wear may cause the suspension arm to break.

Fix: Recalled vehicles will have the subject ball joint retaining nuts checked for correct torque. Should this not be the case both suspension levers and the hub carrier will be changed.

1,577 vehicles · built 1 Sep 2003 to 30 Jun 2008

Due to an anomaly in the ABS/ASR software the Electronic Stability Programme may be disabled. The condition only occurs with the ignition in Key on position and the vehicle battery in a low state of charge

Fix: Recall affected vehicles and replace ABS/ASR ECU.

96 vehicles · built 1 Jan 2007 to 23 Aug 2007

Due to a printing error in the Owner's Manual and Quick Reference Guide the operation of the rear door child safety locks is incorrectly detailed. As a consequence the driver may not operate the door child safety locks correctly.

Fix: Recalled vehicles will have the information pertaining to the operation of the rear door child safety locks updated.

420 vehicles

The steering rack sub-frame may develop a crack in the area of the two fixing points nearest the steering column. This could result in the steering rack becoming loose and a reduction of vehicle control. Potential early symptoms noticed by the driver could be vibrations noises and unusual feeling through the steering wheel.

Fix: Recall the vehicles that are likely to be affected and weld brackets of improved design to the sub-frame.

884 vehicles · built 1 Jun 1998 to 1 Jun 2002

Due to a possible manufacturing defect there is a risk that the internal wiring harness of the door handle may short circuit and trigger the electrical door opening switch of the door. This may result in the door opening without intervention although onboard software of the central locking does not allow this situation to occur over 6mph.

Fix: Recall the vehicles that are likely to be affected and replace the outside door handles.

115 vehicles · built 1 Feb 2004 to 1 Feb 2004

Due to a possible manufacturing defect there is a risk that the fuel hose may separate where the rubber hose joins the metal connector. this may result in fuel leaking into the engine bay with the attendant fire risk.

Fix: Recall affected vehicles and replace pipe with modified type

350 vehicles · built 1 Mar 2001 to 1 Mar 2004

The possibility exists that steering rack fixing bolts may become loose which may result in impaired steering control

Fix: Affected vehicles will be recalled and the subject bolts replaced with quality assured items.

780 vehicles · built 1 Apr 2001 to 1 Apr 2003

The fixing bolts holding the steering idler arms to the chassis may not conform to specification. This may cause the bolts to loosen and result in a loss of steering control.

Fix: Fit quality assured replacement fixing bolts.

69 vehicles · built 1 Jan 1999 to 30 Sep 2000

There is a possibility of a crack appearing in the ninety degree union connecting the vacuum hose to the brake servo unit which may result in loss of servo assistance.

Fix: Recall affected vehicles and replace union with modified type.

84 vehicles · built 1 Jan 1999 to 31 Dec 1999